Cisco IOS XR System Error Reference Guide for XR12000 Series Platform Specific Messages, Release 3.4 - Quality of Service (QoS) Messages [Cisco IOS XR Software]

Table Of Contents

Quality of Service (QoS) Messages

QALLOC Messages

QOS_CLASSIFY_NETIO Messages

QOS_FIFO Messages

QOS_RC_QOSMGR Messages

QOS_TXM Messages

QOS_WRED Messages

QOS Messages

QOSEA Messages

QOSRM_DLL Messages

QOSRM Messages

Quality of Service (QoS) Messages

This section contains all Quality of Service related System Error Messages. The following facility codes are represented in this module:

•QALLOC Messages

•QOS_CLASSIFY_NETIO Messages

•QOS_FIFO Messages

•QOS_RC_QOSMGR Messages

•QOS_TXM Messages

•QOS_WRED Messages

•QOS Messages

•QOSEA Messages

•QOSRM_DLL Messages

•QOSRM Messages

QALLOC Messages
Error Message     
%QOS-QALLOC-3-ALLOC_BLOCK_ERROR [chars]
Explanation An error has occurred while dealing with blocks on the allocated list.
Recommended Action File a DDTS
Error Message     
%QOS-QALLOC-3-COALESCE_ERROR Error Coalescing free queues
Explanation An error has occurred while coalescing free queues
Recommended Action File a DDTS
Error Message     
%QOS-QALLOC-3-ERROR QoSRM-Err: [chars]
Explanation This is an error message from the QoS RM Process, it indicates that something has gone wrong internally in the QoS RM.
Recommended Action File a DDTS
Error Message     
%QOS-QALLOC-3-FREE_BLOCK_ERROR [chars]
Explanation An error has occurred while dealing with blocks on the free list.
Recommended Action File a DDTS
Error Message     
%QOS-QALLOC-3-QUEUE_SANITY Queue value out of bounds ([chars]) Queue: [unsigned int]
Explanation Queue bounds checking has detected an error with a queue value
Recommended Action File a DDTS
Error Message     
%QOS-QALLOC-4-WARN QoSRM-Warn: [chars]
Explanation This is a warning message from the QoS RM Process
Recommended Action *RECUR*
Error Message     
%QOS-QALLOC-6-INFO QoSRM-Info: [chars]
Explanation This is an informational message from the QoS RM Process
Recommended Action *RECUR*
Error Message     
%QOS-QALLOC-7-DEBUG QoSRM-Debug: [chars]
Explanation This is a debuging message from the QoS RM Process
Recommended Action *NONE*

QOS_CLASSIFY_NETIO Messages
Error Message     
%QOS-QOS_CLASSIFY_NETIO-7-DEBUG_INIT_ERROR A error occurred during debug initialization. Error: [chars]
Explanation The QoS Classify DLL encountered an error while initializing the debug facility. This is not a fatal error. QoS Classify will continue to execute properly, but will not be able to use the debugging facility.
Recommended Action None

QOS_FIFO Messages
Error Message     
%QOS-QOS_FIFO-7-DEBUG_INIT_ERROR An error occurred during debug initialization, err: [chars]
Explanation The FIFO QoSMgr component encountered an error during debug initialization This is not a fatal condition. FIFO queueuing will work properly but will not be able to use any of the debugging facilities.
Recommended Action None
Error Message     
%QOS-QOS_FIFO-7-DEBUG_INIT_ERROR An error occurred during debug initialization. Error: [chars]
Explanation The QoS FIFO dll encountered a problem while initializingg the debug facility. This is not a fatal error. QoS FIFO will continue to execute properly, but will not be able to use the debugging facility.
Recommended Action None

QOS_RC_QOSMGR Messages
Error Message     
%QOS-QOS_RC_QOSMGR-4-INVALID_CFG [chars]
Explanation An invalid or unsupported policer has been configured.
Recommended Action Please correct the configuration as indicated in the message.
Error Message     
%QOS-QOS_RC_QOSMGR-4-INVALID_INTF_TYPE Policer Action [chars] has been configured on an un-supported interface type
Explanation An invalid or unsupported policer has been configured.
Recommended Action Please correct the configuration as indicated in the message.
Error Message     
%QOS-QOS_RC_QOSMGR-4-INVALID_PEAK_RATE Configured peak-rate ([dec] [chars]) should be more than the configured conform rate ([dec] [chars])
Explanation The peak-rate was configured less than the conform rate, which is not allowed.
Recommended Action Increase the peak-rate or reduce the conform rate to satisfy the above requirement.
Error Message     
%QOS-QOS_RC_QOSMGR-4-INVALID_UNIT An invalid or incompatible unit '[chars]' ([dec]) was specified for [chars]
Explanation An invalid unit has been specified for the feature mentioned in the message.
Recommended Action Correct the policy-map so that a correct unit value is specified for the feature being configured
Error Message     
%QOS-QOS_RC_QOSMGR-4-NOT_SUPPORTED Action [chars] not supported on [chars]
Explanation The policy has an action that is not supported .
Recommended Action Correct the policy-map to correct the action to a supported action.
Error Message     
%QOS-QOS_RC_QOSMGR-4-RC_BUNDLE_BW_NOPCT Absolute bw specified for bundle interfaces, use percentage values instead
Explanation For bundle interfaces, the bandwidth must be specified in percentage values of absolute values.
Recommended Action Correct the policy-map so that the bandwidth value is specified as a percentage of the total bandwidth and then reapply the policy-map
Error Message     
%QOS-QOS_RC_QOSMGR-4-RC_BW_EXCEED Policer rate exceeds 100 percent of the interface bandwidth
Explanation The Policer rate in the policy-map exceeds the maximum bandwidth that the interface can support.
Recommended Action Correct the policy-map so that the policer rate is smaller than the maximum of the interface it has been applied to.
Error Message     
%QOS-QOS_RC_QOSMGR-4-TOO_MANY_ACTIONS More than [dec] [chars] actions can not be configured.
Explanation More than the maximum supported actions of the category mentioned in the message have been configured.
Recommended Action Reduce the number of actions so they don't exceed the max allowed.
Error Message     
%QOS-QOS_RC_QOSMGR-4-VALUE_TOO_LARGE The value specified for [chars] is too large and cannot be handled by the system
Explanation The value configured for the feature mentioned in the message is too large.
Recommended Action Use a value which is less than 4294967295 kbps or KBytes (depending on the type of parameter configured).
Error Message     
%QOS-QOS_RC_QOSMGR-7-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The QoSMgr policer component encountered an error during debug initialization This is not a fatal condition. Policing will work properly but will not be able to use any of the debugging facilities.
Recommended Action None

QOS_TXM Messages
Error Message     
%QOS-QOS_TXM-4-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The QOS Mark process encounterd an error while initializing the debug facility. This is not a fatal error. QOS Marking will continue to execute properly, but will not be able to use the debuging facility.
Recommended Action None
Error Message     
%QOS-QOS_TXM-7-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars]
Explanation The QOS TXM process encountered an error while initializing the debug facility. This is not a fatal error. QOS TXM will continue to execute properly, but will not be able to use the debugging facility.
Recommended Action None
Error Message     
%QOS-QOS_TXM-7-UNINITIALISE_ERROR An error occurred in initialization sequence for iface: [chars]
Explanation The QOS TXM process encountered an error in its initialsation sequence. This is a serious error. QOS TXM functioning correctly is not guranteed depending upon the exact problem in initialisation sequence
Recommended Action None

QOS_WRED Messages
Error Message     
%QOS-QOS_WRED-7-DEBUG_INIT_ERROR An error occurred during debug initialization. Error: [chars]
Explanation The QoS WRED dll encountered a problem while initializing the debug facility. This is not a fatal error. QoS WRED will continue to execute properly, but will not be able to use the debugging facility.
Recommended Action None
Error Message     
%QOS-QOS_WRED-7-INVALID_WRED_TYPE The type of random-detect configured under class '[chars]' is invalid or not supported on this platform. Please configure a supported random-detect type.
Explanation An invalid type of random-detect was configured for the class specified in the message.
Recommended Action Please reconfigure the policy-map with a supported type of random-detect. If the configured type of random-detect is supported on this platform and this message is seen, please contact the customer support with the following information.

QOS Messages
Error Message     
%QOS-QOS-2-MALLOC_FAIL Memory alloc error [chars] [chars]
Explanation The router cannot allocate more memory.
Recommended Action It may be necessary to free some memory by exiting a program.
Error Message     
%QOS-QOS-3-BW_BUNDLE_ABSOLUTE Absolute values cannot be used for policies configured on Bundle interfaces. Use percentage values instead
Explanation If the policy is applied on the bundle interface, the policer/shaper values must be configured in percentages.
Recommended Action Reconfigure policy to use percentage values instead of absolute values.
Error Message     
%QOS-QOS-3-BW_SUM_EXCEEDS_100_PC Sum of bandwidth allocated to all classes exceeds 100 percent. Allocated BW : [dec] percent
Explanation Allocated bandiwdth total including the default class can not exceed beyond 100%.
Recommended Action Reconfigure policy to assign appropriate bandiwdth guarantees.
Error Message     
%QOS-QOS-3-CHKPT_GET_DATA_FAIL Failed to get QoS init data during restart. Remove policy [chars] from interface [chars], direction [chars] and re-add to recover.
Explanation Getting init data from qos ma on RP could fail if there are any issues in restart code path in RP.
Recommended Action Remove the policy and add it back
Error Message     
%QOS-QOS-3-CONNECT_FAIL Server connection failed - [chars]. Error code - [chars]
Explanation Connection to some server failed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-DEBUG_FAIL Error occurred while registering for debugging services
Explanation Error occurred while waiting for an event.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-DEF_CLASS_BW_EXCEED_99_PC Sum of bandwidth allocated to non-default classes exceeds 99 percent. Allocated BW : [dec] percent
Explanation Allocated bandiwdth total can not exceed beyond 99% as 1% has to be reserved for the default class.
Recommended Action Reconfigure policy to assign appropriate bandiwdth guarantees.
Error Message     
%QOS-QOS-3-DLL_INIT_FAIL Could not initialize [chars] dll. Error code - [chars]
Explanation An error was encountered while trying to initialize a DLL that supports a given feature. Both the DLL name and the error code are displayed. This is a critical error in the QOS component. It indicates that the DLL that implements a feature does not provide an initializing function. This indicates that some QOS feature is not working properly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-EVM_CREATE_FAIL Failed to create event manager
Explanation Failed to create event manager.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-FEATURE_ADD_FAIL Failed to add policy [chars], class = [chars], feature = [chars].
Explanation Failed to add the specified feature while applying the specified service policy.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-FILE_ERROR File [chars] error: [chars]. Reason: [chars]
Explanation An error was encountered while accessing a file. Both the file name and the error reason are displayed. This is a critical error in the QOS component. It indicates that the file that defines a feature is missing from the system and the related QOS feature will not work properly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-FILE_WRONG_INFO File [chars] [chars] [dec]
Explanation An error was encountered while accessing a file. Both the file name and the error reason are displayed. This is a critical error in the QOS component. It indicates that the file that defines a feature is missing from the system and the related QOS feature will not working properly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-FT_CONFIGURE_FAIL Failed to configure feature [chars]. Error code - [chars]
Explanation The specified feature could not be configured due to the specified reason.
Recommended Action Please turn on debugs using the following command: debug qos control all dev
Error Message     
%QOS-QOS-3-FT_REMOVE_FAIL Failed to remove the feature [chars]. Error code - [chars]
Explanation The QOS Manager process failed to remove the specified feature. The error code is also displayed.
Recommended Action Please turn on debugs using the following command: debug qos control all dev and reenter the configuration command that caused the error. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-FT_SEND_FAIL Sending control to [chars] feature failed
Explanation Failed to send a control feature information to the Execution Agent. The name of the feature is displayed.
Recommended Action Please turn on debugs using the following command: debug qos control all dev and reenter the configuration command that caused the error. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-MAX_CLASS_EXCEEDED_FOR_FABQOS Policy exceeds number of classes allowed for FabQoS
Explanation Fabric QoS policy can only have a maximum of 3 classes. If the number of classes is more than 3, policy map is rejected.
Recommended Action Reconfigure policy map to adjust number of classes
Error Message     
%QOS-QOS-3-MGR_DLL_OPEN_FAIL Could not open [chars] DLL. Error code - [chars]
Explanation An error was encountered while trying to open a DLL that supports a given feature. Both the DLL name and the error code are displayed. This is a critical error in the QOS component. It indicates that the DLL that implements the feature is not present in the system. This indicates that some QOS feature is not working properly.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-MSG_SEND_FAIL Failed to send message to feature [chars] [chars]. Error code - [chars]
Explanation Failed to send the a message to the specified feature due to the error message displayed.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-ONLY_PRI_OR_BW_REM_PERCENT_ALLOWED Can not configure anything other than priority or bandwidth remaining percent for a fabqos policy
Explanation Only priority and bandwidth remaining percent commands are supported for FabQoS policy.
Recommended Action Reconfigure policy to use these two commands.
Error Message     
%QOS-QOS-3-OVER_SUBSCRIPTION_OF_MIN_BW_GAURANTEES There is oversubscription of minimum bandwidth guarantees, taking HP bandwidth into account. Bandwidth guarantees may not be met for this policy. Allocated BW : [dec] percent
Explanation With high priority class configured and the bandwidth guarantee for the HP taken into account, the interface may have been oversubscribed. This could cause some packets from the class that has bandwidth guarantee configured to be dropped.
Recommended Action Reconfigure policy to achieve optimal bandwidth guarantee results.
Error Message     
%QOS-QOS-3-POLICY_CHECK_FAIL Failed to configure policy - [chars]. Error code - [chars]
Explanation The policy could not be configured on the interface as the policy itself or one of its child policies does not exist. The error code is also displayed.
Recommended Action Please turn on debugs using the following command: debug qos control qosmgr dev and reenter the configuration command that caused the error. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-QFIFO_DEBUG_NETIO_INIT_FAIL Failed to Initialize debug netion - [chars] Error : [chars]
Explanation Debug initialization failed for NetIO. Debugs may not be printed.
Recommended Action Try restarting qos_ma_ea process.
Error Message     
%QOS-QOS-3-UNSUPPORTED_IP_OR_MPLS_MATCH_CONFIG match on ip or mpls packet fields is not supported on a policy attached to layer2 interface
Explanation Matching on layer3 packet fields such as dscp, prec, exp on a service policy attached to an Access Circuit is not supported. Packets received and transmitted on an AC are considered layer2 packets, packet headers beyond L2 are not parsed in the hardware
Recommended Action Remove match statements that match on layer3 fields of a packet in the classmaps used by the service policy
Error Message     
%QOS-QOS-3-UNSUPPORTED_L2_MATCH_CONFIG match on mac address is not supported on a policy attached to layer3 interface
Explanation Matching on source or destination mac address on a policy attached to layer-3 interfaces such as routed vlan or POS interfaces is not supported
Recommended Action Remove invalid match statements in the classmaps used by the service policy
Error Message     
%QOS-QOS-3-UNSUPPORTED_MAC_ADDR_MATCH_CONFIG match on src/dst mac is not supported on output/input l2 service policy
Explanation Matching on mac address in an l2 service policy is supported with the following constraints: Match on source mac address is supported only on input l2 service policy Match on destination mac address is supported only on output l2 service policy
Recommended Action Remove unsupported match statements in the classmaps used by the service policy
Error Message     
%QOS-QOS-3-UNSUPPORTED_MARKING_CONFIG Invalid marking configuration in service policy attached to layer2 interface
Explanation On service policy attached to an AC, marking of certain fields is not supported. The following marking configurations are invalid: Ingress/Egress: ip dscp, ip precedence, mpls exp topmost Egress: mpls exp imposition, qos-group, discard-class
Recommended Action Remove invalid 'set' statements from the policymap
Error Message     
%QOS-QOS-3-UNSUPPORTED_MATCH_COS_CONFIG match cos command is not supported on layer-3 interface egress policies. Invalid Configuration.
Explanation 'match cos' command is not supported on service policy applied to layer-3 interfaces since layer2 encapsulations are removed before packets are sent to egress.
Recommended Action Remove invalid 'match cos' command from class-map
Error Message     
%QOS-QOS-3-UNSUPPORTED_MIN_BW_CONFIG Bandwidth command is not supported on the ingress side. Invalid Configuration.
Explanation Bandwidth command is not supported on ingress policies. Instead, configure 'bandwidth remaining' to assign weights for the different queues.
Recommended Action Configure policy without 'bandwidth' on the ingress.
Error Message     
%QOS-QOS-3-UNSUPPORTED_MULTIPLE_POLICER_ACTIONS multiple set commands in a policer action are not supported
Explanation Only one set command is allowed on each of conform, exceed and violate actions of a policer.
Recommended Action Remove multiple set commands on policer conform/exceed/violate action
Error Message     
%QOS-QOS-3-UNSUPPORTED_POLICER_MARKING_CONFIG Invalid policer marking configuration in service policy attached to layer2 interface
Explanation On service policy attached to an AC, policer marking of certain fields is not supported. The following policer marking configurations are invalid: Ingress/Egress: ip dscp, ip precedence, mpls exp topmost Egress: mpls exp imposition
Recommended Action Remove invalid 'police' statements from the policymap
Error Message     
%QOS-QOS-3-UNSUPPORTED_POLICER_MARKING_L2_COS_CONFIG Invalid policer marking configuration in service policy attached to layer3 interface
Explanation On service policy attached to a layer-3 interface, policer marking of layer-2 CoS field is not supported.
Recommended Action Remove 'set cos' action on 'police' command from the policymap
Error Message     
%QOS-QOS-3-UNSUPPORTED_POLICER_RATE Unsupported policer value used in policymap : [dec] kbps. It must be less than 16 Gbps
Explanation Configured policer value can not be more than 16Gbps. Policy map is rejected.
Recommended Action Reconfigure policy map to configure appropriate policer value.
Error Message     
%QOS-QOS-3-UNSUPPORTED_Q_LIMIT_CONFIG In order to configure queue-limit for a class, atleast one feature that allocates a separate queue for that class needs to be configured.
Explanation If queue-limit command for a class is configured, then that class requires a separate queue (due to h/w implementation). Since the user has not configured any feature for this class that allocates a separate queue for that class, the user is not allowed to configure queue-limit for that class.
Recommended Action Configure policy with a feature which allocates a separate queue.
Error Message     
%QOS-QOS-3-UNSUPPORTED_WRED_CONFIG Invalid wred profile type in service policy attached to layer2 interface
Explanation On service policy attached to an AC, valid wred profile types are layer2_cos discard-class and default
Recommended Action Remove invalid 'random-detect' statements from the policymap
Error Message     
%QOS-QOS-3-WAIT_ERR Error occurred while waiting for an event
Explanation Error occurred while waiting for an event.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-3-WRONG_QUANTAS_SPECIFIED Bandwidth remaining should only be specified in multiples of 5
Explanation Bandwidth remaining commnad has a limitation where the percentages can only be specified in multiples of 5. If not, policy map is rejected.
Recommended Action Reconfigure policy to configure quantas in multiples of 5
Error Message     
%QOS-QOS-4-ERR_EVM_EVENT_BLOCK Unrecoverable error in event loop. Error: [chars]
Explanation An error (other than EINTR) occured in the event loop. The process has exited and restarted.
Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-4-NODE_INSTL_FAIL Could not install [chars] feature [chars]
Explanation An error was encountered while trying to add the specified feature node to NetIO. Both the feature name and the error code are displayed. This is a critical error in the QOS component. It indicates that some QOS feature is not working properly.
Recommended Action Please provide the output of the commands: Please provide the output of the commands: show running configuration show qos trace
Error Message     
%QOS-QOS-4-Q_THRESHOLD_EXCEEDS_MAX [chars]
Explanation Ingress and egress queuing asics support a maximum packet buffering capacity of 1 Gbytes. Therefore queue-limit or RED thresholds of greater than 1 Gbytes (1073741824 bytes) cannot be configured and will be automatically set to the maximum permissible value.
Recommended Action Please re-evaluate the value of queue-limit and/or RED thresholds since it is unlikely that such a high value is necessary.
Error Message     
%QOS-QOS-4-WRED_THRESH_MORE_THAN_QUEUE_LIMIT Min or max threshold for one or more RED profiles of class [chars] is greater than queue limit ([dec] bytes)
Explanation Since min or max threshold is greater than queue limit, RED will not take effect or partially take effect for one or more RED profiles of this class.
Recommended Action Set RED min and max threshold to be below queue limit.
Error Message     
%QOS-QOS-5-PARENT_HAS_NO_BW_MIN_CONFIGURED Child class bandwidth minimum is reduced to zero due no minimum bandwidth guarantee in parent
Explanation Bandwidth command in a child class requires similar command in the parent class. Otherwise minimum bandwidth guaranteed for child class would be zero
Recommended Action Reconfigure policy to assign bandwidth guarantee in the parent class before the gaurantee is given to the child class.
Error Message     
%QOS-QOS-6-HPOLICY_ATTACH_FAIL Too many levels of hierarchy in policy [chars].
Explanation The Policy could not be installed because it has more than 2 levels of hierarchy.
Recommended Action Simplify the policy-map to include no more than 2 levels of hierarchy. and reapply it.
Error Message     
%QOS-QOS-6-POLICY_ATTACH_FAIL Service policy [chars] could not be attached to [chars]. Error code - [chars]
Explanation Policy could not be installed. The reason is displayed.
Recommended Action Please verify that the specified policy has been configured with the following command: show running configuration
Error Message     
%QOS-QOS-7-CLASSMAP_NOT_FOUND Class map [chars] not found
Explanation The specified class map was not found. Make sure that it is properly configured. If not, please confifure it.
Recommended Action Verify that the specified class-map name is properly configured by issuing the following command show running class-map
Error Message     
%QOS-QOS-7-CONNECT_FAIL Server connection failed - [chars]. Error code - [chars]
Explanation Connection to IMP server failed during process init.
Recommended Action No action is required. Process will be automatically restarted. If not recovered, it is a fatal condition. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *REDUCE*
Error Message     
%QOS-QOS-7-DLL_REGISTER_CERR_FAIL Could not register error codes for [chars] dll. Error code - [chars]
Explanation Could not get register DLL error codes. This is not a critical error. The QOS Manager will function properly, but will not be able to use any of the debug facilities.
Recommended Action None
Error Message     
%QOS-QOS-7-ENS_ERROR ENS Debug:[chars] rc=[chars]
Explanation The ENS/NRS infrastructure is not available.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-7-ERR_BAG_REGISTER Failed to register bag structures with bag server (Reason: [chars])
Explanation The process could not register the data structures used by QoS statistics and management agents. This is not a critical error Qos will work properly. However show commands may not work.
Recommended Action None
Error Message     
%QOS-QOS-7-ERR_EVM_ASYNC_ATTACH Failed to attach handler for async events: [chars]
Explanation Failed to attach handler for async events.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-7-ERR_EVM_CREATE Failed to create event manager
Explanation Failed to create event manager.
Recommended Action None
Error Message     
%QOS-QOS-7-ERR_EVM_CREATE Failed to create event manager
Explanation Failed to create event manager.
Recommended Action No action is required. Process will be automatically restarted. If not recovered, it is a fatal condition. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. *REDUCE*
Error Message     
%QOS-QOS-7-ERR_MEM_ALLOC [chars]
Explanation The QOS manager process could not get memory for the specified memory usage. This condition will occur if the system is low on memory.
Recommended Action None
Error Message     
%QOS-QOS-7-ERR_SYSDB SysDB error [chars]. Error code - [chars]
Explanation There were problems communicating with the SysDB. The reason and error message are displayed. If this message is displayed, the qosmgr process will restart itself.
Recommended Action None
Error Message     
%QOS-QOS-7-EVENT_CONN_ERR Error in [chars]: [chars]
Explanation Error encountered in opening connection to a required server. If this error occurs, the QoS Manager will restart itself.
Recommended Action None
Error Message     
%QOS-QOS-7-IM_CONNECT_FAIL Interface control server connection failed - [chars]. Error code - [chars]
Explanation Connection to interface manager failed. If this contition occurs, the QOS Manager will restart itself.
Recommended Action None
Error Message     
%QOS-QOS-7-NETIO_SET_PAK_SHAPEQ_FAIL Failed to set packet shape Q - [chars] Error : [chars]
Explanation Could not set the queue where this packet is supposed to be queued. As a consequence the packet is being dropped.
Recommended Action Try removing the policy and reapplying it.
Error Message     
%QOS-QOS-7-OVL_RGST_FAIL Could not register ovl notification handler. Error code - [chars]
Explanation An error was encountered while trying to register the OVL notification handler.
Recommended Action None
Error Message     
%QOS-QOS-7-POLICY_INSTALL_FAIL Policy could not be installed [chars] [chars] Error code - [chars]
Explanation The specified policy could not be attached to an interface due to the specified reason.
Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information.
Error Message     
%QOS-QOS-7-POLICY_NOT_FOUND Policy [chars] not found
Explanation The specified policy name was not found. Make sure that it is properly configured. If not please configure it.
Recommended Action Verify that the specified policy map is properly configured by issuing the following command show running policy-map .
Error Message     
%QOS-QOS-7-POLICY_REMOVE_FAIL Failed to remove policy [chars]. Error= [chars]
Explanation The specified policy could not be removed from an interface due to the specified reason.
Recommended Action Please follow the instructions from the error message.

QOSEA Messages
Error Message     
%QOS-QOSEA-3-ERROR QoSEA-Err: [chars]
Explanation This is an error message from the QoS EA Process, it indicates that something has gone wrong internally in the QoS EA.
Recommended Action File a DDTS
Error Message     
%QOS-QOSEA-3-MSG_CHAN Could not create Msg chan: [chars] error: [chars]
Explanation The QoS EA could not create the necessary message channel due to the given error
Recommended Action *DDTS*
Error Message     
%QOS-QOSEA-3-MSG_HANDLER_ERR An error occurred in the [chars] message handler
Explanation An error occurred during message handling in the indicated message handler
Recommended Action File a DDTS
Error Message     
%QOS-QOSEA-3-POLICY_ERROR QoSEA-Err: class:[chars], [chars]
Explanation This is an error message from the QoS EA Process, it indicates that something has gone wrong while trying to configure a service policy.
Recommended Action *NONE*
Error Message     
%QOS-QOSEA-3-UNHANDLED_MSG The QoS EA received an unhandled message
Explanation The QoS EA received a message that it was unable to handle'
Recommended Action *DDTS*
Error Message     
%QOS-QOSEA-3-UNKNOWN_MSG An unknown message was dispatched to the [chars] message handler: Msg: [hex]
Explanation An incoming message was demuxed to the incorrect message handler
Recommended Action File a DDTS
Error Message     
%QOS-QOSEA-4-WARN QoSEA-Warn: [chars]
Explanation This is a warning message from the QoS EA Process
Recommended Action *RECUR*
Error Message     
%QOS-QOSEA-5-NOTICE QoSEA-Notice: [chars]
Explanation This is a notice message from the QoS EA Process
Recommended Action *NONE*
Error Message     
%QOS-QOSEA-6-INFO QoSEA-Info: [chars]
Explanation This is an informational message from the QoS EA Process
Recommended Action *RECUR*
Error Message     
%QOS-QOSEA-6-MSG_ASYNC An Asynchronous message was received
Explanation The QoS EA received an asynchronous message.
Recommended Action *NONE*
Error Message     
%QOS-QOSEA-6-POLICY_INFO QoSEA-Info: class:[chars], [chars]
Explanation This is an informational message from the QoS EA Process. It indicates that something can not be configure in service policy.
Recommended Action *NONE*
Error Message     
%QOS-QOSEA-7-DEBUG QoSEA-Debug: [chars]
Explanation This is a debuging message from the QoS EA Process
Recommended Action *NONE*

QOSRM_DLL Messages
Error Message     
%QOS-QOSRM_DLL-3-ERROR QoSRM-DLL-Err: [chars]
Explanation This is an error message from the QoS RM DLL, it indicates that something has gone wrong internally in the QoS RM dll.
Recommended Action File a DDTS
Error Message     
%QOS-QOSRM_DLL-3-MSG_CHAN Could not create Msg chan: [chars] error: [chars]
Explanation The QoS RM dll could not create the necessary message channel due to the given error
Recommended Action *DDTS*
Error Message     
%QOS-QOSRM_DLL-3-MSG_HANDLER_ERR An error ([chars]) occurred in the [chars] message handler,Msg:[hex]
Explanation An error occurred during message handling in the indicated message handler
Recommended Action File a DDTS
Error Message     
%QOS-QOSRM_DLL-3-UNHANDLED_MSG The QoS RM dll received an unhandled message
Explanation The QoS RM dll received a message that it was unable to handle'
Recommended Action *DDTS*
Error Message     
%QOS-QOSRM_DLL-3-UNKNOWN_MSG An unknown message was dispatched to the [chars] message handler: Msg: [hex]
Explanation An incoming message was demuxed to the incorrect message handler
Recommended Action File a DDTS
Error Message     
%QOS-QOSRM_DLL-3-UNKNOWN_QTYPE Unknown Q-Type in message: [hex]
Explanation The QoS RM dll received a message, but was unable to determine which resource the message was intended for because the Q-Type field was incorrect.
Recommended Action File a DDTS
Error Message     
%QOS-QOSRM_DLL-4-WARN QoSRM-DLL-Warn: [chars]
Explanation This is a warning message from the QoS RM DLL
Recommended Action *RECUR*
Error Message     
%QOS-QOSRM_DLL-6-INFO QoSRM-DLL-Info: [chars]
Explanation This is an informational message from the QoS RM DLL
Recommended Action *RECUR*
Error Message     
%QOS-QOSRM_DLL-6-MSG_ASYNC An Asynchronous message was received
Explanation The QoS RM dll received an asynchronous message.
Recommended Action *NONE*
Error Message     
%QOS-QOSRM_DLL-7-DEBUG QoSRM-DLL-Debug: [chars]
Explanation This is a debuging message from the QoS RM DLL
Recommended Action *NONE*

QOSRM Messages
Error Message     
%QOS-QOSRM-3-ERROR QoSRM-Err: [chars]
Explanation This is an error message from the QoS RM Process, it indicates that something has gone wrong internally in the QoS RM.
Recommended Action File a DDTS
Error Message     
%QOS-QOSRM-3-MSG_CHAN Could not create Msg chan: [chars] error: [chars]
Explanation The QoS RM could not create the necessary message channel due to the given error
Recommended Action *DDTS*
Error Message     
%QOS-QOSRM-3-MSG_HANDLER_ERR Event: [chars] occurred in the [chars] message handler, Msg:[hex]
Explanation An error occurred during message handling in the indicated message handler
Recommended Action File a DDTS
Error Message     
%QOS-QOSRM-3-UNHANDLED_MSG The QoS RM received an unhandled message
Explanation The QoS RM received a message that it was unable to handle'
Recommended Action *DDTS*
Error Message     
%QOS-QOSRM-3-UNKNOWN_MSG An unknown message was dispatched to the [chars] message handler: Msg: [hex]
Explanation An incoming message was demuxed to the incorrect message handler
Recommended Action File a DDTS
Error Message     
%QOS-QOSRM-3-UNKNOWN_QTYPE Unknown Q-Type in message: [hex]
Explanation The QoS RM received a message, but was unable to determine which resource the message was intended for because the Q-Type field was incorrect.
Recommended Action File a DDTS
Error Message     
%QOS-QOSRM-4-WARN QoSRM-Warn: [chars]
Explanation This is a warning message from the QoS RM Process
Recommended Action *RECUR*
Error Message     
%QOS-QOSRM-6-INFO QoSRM-Info: [chars]
Explanation This is an informational message from the QoS RM Process
Recommended Action *RECUR*
Error Message     
%QOS-QOSRM-6-MSG_ASYNC An Asynchronous message was received
Explanation The QoS RM received an asynchronous message.
Recommended Action *NONE*
Error Message     
%QOS-QOSRM-7-DEBUG QoSRM-Debug: [chars]
Explanation This is a debuging message from the QoS RM Process
Recommended Action *NONE*

	Cisco IOS XR System Error Reference Guide for XR12000 Series Platform Specific Messages, Release 3.4
	Quality of Service (QoS) Messages
Cisco IOS XR System Error Reference Guide for XR12000 Series Platform Specific Messages, Release 3.4 Preface Overview Access Control List (ACL) Messages Diagnostic Messages Forwarding Messages High Availability (HA) Messages Installation Messages Internet Protocol (IP) Messages Layer 1 Messages Layer 2 Messages Manageability (MGBL) Messages Operating System (OS) Messages Packet Infrastructure Messages Platform Messages Quality of Service (QoS) Messages Routing Messages Index	Download this chapter Quality of Service (QoS) Messages Download the complete book Book-level PDF: Cisco IOS XR System Error Reference Guide for XR12000 Series Platform Specific Messages (PDF - 3 MB) Table Of Contents Quality of Service (QoS) Messages QALLOC Messages QOS_CLASSIFY_NETIO Messages QOS_FIFO Messages QOS_RC_QOSMGR Messages QOS_TXM Messages QOS_WRED Messages QOS Messages QOSEA Messages QOSRM_DLL Messages QOSRM Messages Quality of Service (QoS) Messages This section contains all Quality of Service related System Error Messages. The following facility codes are represented in this module: •QALLOC Messages •QOS_CLASSIFY_NETIO Messages •QOS_FIFO Messages •QOS_RC_QOSMGR Messages •QOS_TXM Messages •QOS_WRED Messages •QOS Messages •QOSEA Messages •QOSRM_DLL Messages •QOSRM Messages QALLOC Messages Error Message %QOS-QALLOC-3-ALLOC_BLOCK_ERROR [chars] Explanation An error has occurred while dealing with blocks on the allocated list. Recommended Action File a DDTS Error Message %QOS-QALLOC-3-COALESCE_ERROR Error Coalescing free queues Explanation An error has occurred while coalescing free queues Recommended Action File a DDTS Error Message %QOS-QALLOC-3-ERROR QoSRM-Err: [chars] Explanation This is an error message from the QoS RM Process, it indicates that something has gone wrong internally in the QoS RM. Recommended Action File a DDTS Error Message %QOS-QALLOC-3-FREE_BLOCK_ERROR [chars] Explanation An error has occurred while dealing with blocks on the free list. Recommended Action File a DDTS Error Message %QOS-QALLOC-3-QUEUE_SANITY Queue value out of bounds ([chars]) Queue: [unsigned int] Explanation Queue bounds checking has detected an error with a queue value Recommended Action File a DDTS Error Message %QOS-QALLOC-4-WARN QoSRM-Warn: [chars] Explanation This is a warning message from the QoS RM Process Recommended Action RECUR Error Message %QOS-QALLOC-6-INFO QoSRM-Info: [chars] Explanation This is an informational message from the QoS RM Process Recommended Action RECUR Error Message %QOS-QALLOC-7-DEBUG QoSRM-Debug: [chars] Explanation This is a debuging message from the QoS RM Process Recommended Action NONE QOS_CLASSIFY_NETIO Messages Error Message %QOS-QOS_CLASSIFY_NETIO-7-DEBUG_INIT_ERROR A error occurred during debug initialization. Error: [chars] Explanation The QoS Classify DLL encountered an error while initializing the debug facility. This is not a fatal error. QoS Classify will continue to execute properly, but will not be able to use the debugging facility. Recommended Action None QOS_FIFO Messages Error Message %QOS-QOS_FIFO-7-DEBUG_INIT_ERROR An error occurred during debug initialization, err: [chars] Explanation The FIFO QoSMgr component encountered an error during debug initialization This is not a fatal condition. FIFO queueuing will work properly but will not be able to use any of the debugging facilities. Recommended Action None Error Message %QOS-QOS_FIFO-7-DEBUG_INIT_ERROR An error occurred during debug initialization. Error: [chars] Explanation The QoS FIFO dll encountered a problem while initializingg the debug facility. This is not a fatal error. QoS FIFO will continue to execute properly, but will not be able to use the debugging facility. Recommended Action None QOS_RC_QOSMGR Messages Error Message %QOS-QOS_RC_QOSMGR-4-INVALID_CFG [chars] Explanation An invalid or unsupported policer has been configured. Recommended Action Please correct the configuration as indicated in the message. Error Message %QOS-QOS_RC_QOSMGR-4-INVALID_INTF_TYPE Policer Action [chars] has been configured on an un-supported interface type Explanation An invalid or unsupported policer has been configured. Recommended Action Please correct the configuration as indicated in the message. Error Message %QOS-QOS_RC_QOSMGR-4-INVALID_PEAK_RATE Configured peak-rate ([dec] [chars]) should be more than the configured conform rate ([dec] [chars]) Explanation The peak-rate was configured less than the conform rate, which is not allowed. Recommended Action Increase the peak-rate or reduce the conform rate to satisfy the above requirement. Error Message %QOS-QOS_RC_QOSMGR-4-INVALID_UNIT An invalid or incompatible unit '[chars]' ([dec]) was specified for [chars] Explanation An invalid unit has been specified for the feature mentioned in the message. Recommended Action Correct the policy-map so that a correct unit value is specified for the feature being configured Error Message %QOS-QOS_RC_QOSMGR-4-NOT_SUPPORTED Action [chars] not supported on [chars] Explanation The policy has an action that is not supported . Recommended Action Correct the policy-map to correct the action to a supported action. Error Message %QOS-QOS_RC_QOSMGR-4-RC_BUNDLE_BW_NOPCT Absolute bw specified for bundle interfaces, use percentage values instead Explanation For bundle interfaces, the bandwidth must be specified in percentage values of absolute values. Recommended Action Correct the policy-map so that the bandwidth value is specified as a percentage of the total bandwidth and then reapply the policy-map Error Message %QOS-QOS_RC_QOSMGR-4-RC_BW_EXCEED Policer rate exceeds 100 percent of the interface bandwidth Explanation The Policer rate in the policy-map exceeds the maximum bandwidth that the interface can support. Recommended Action Correct the policy-map so that the policer rate is smaller than the maximum of the interface it has been applied to. Error Message %QOS-QOS_RC_QOSMGR-4-TOO_MANY_ACTIONS More than [dec] [chars] actions can not be configured. Explanation More than the maximum supported actions of the category mentioned in the message have been configured. Recommended Action Reduce the number of actions so they don't exceed the max allowed. Error Message %QOS-QOS_RC_QOSMGR-4-VALUE_TOO_LARGE The value specified for [chars] is too large and cannot be handled by the system Explanation The value configured for the feature mentioned in the message is too large. Recommended Action Use a value which is less than 4294967295 kbps or KBytes (depending on the type of parameter configured). Error Message %QOS-QOS_RC_QOSMGR-7-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars] Explanation The QoSMgr policer component encountered an error during debug initialization This is not a fatal condition. Policing will work properly but will not be able to use any of the debugging facilities. Recommended Action None QOS_TXM Messages Error Message %QOS-QOS_TXM-4-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars] Explanation The QOS Mark process encounterd an error while initializing the debug facility. This is not a fatal error. QOS Marking will continue to execute properly, but will not be able to use the debuging facility. Recommended Action None Error Message %QOS-QOS_TXM-7-DEBUG_INIT_ERROR A error occurred during debug initialization, err: [chars] Explanation The QOS TXM process encountered an error while initializing the debug facility. This is not a fatal error. QOS TXM will continue to execute properly, but will not be able to use the debugging facility. Recommended Action None Error Message %QOS-QOS_TXM-7-UNINITIALISE_ERROR An error occurred in initialization sequence for iface: [chars] Explanation The QOS TXM process encountered an error in its initialsation sequence. This is a serious error. QOS TXM functioning correctly is not guranteed depending upon the exact problem in initialisation sequence Recommended Action None QOS_WRED Messages Error Message %QOS-QOS_WRED-7-DEBUG_INIT_ERROR An error occurred during debug initialization. Error: [chars] Explanation The QoS WRED dll encountered a problem while initializing the debug facility. This is not a fatal error. QoS WRED will continue to execute properly, but will not be able to use the debugging facility. Recommended Action None Error Message %QOS-QOS_WRED-7-INVALID_WRED_TYPE The type of random-detect configured under class '[chars]' is invalid or not supported on this platform. Please configure a supported random-detect type. Explanation An invalid type of random-detect was configured for the class specified in the message. Recommended Action Please reconfigure the policy-map with a supported type of random-detect. If the configured type of random-detect is supported on this platform and this message is seen, please contact the customer support with the following information. QOS Messages Error Message %QOS-QOS-2-MALLOC_FAIL Memory alloc error [chars] [chars] Explanation The router cannot allocate more memory. Recommended Action It may be necessary to free some memory by exiting a program. Error Message %QOS-QOS-3-BW_BUNDLE_ABSOLUTE Absolute values cannot be used for policies configured on Bundle interfaces. Use percentage values instead Explanation If the policy is applied on the bundle interface, the policer/shaper values must be configured in percentages. Recommended Action Reconfigure policy to use percentage values instead of absolute values. Error Message %QOS-QOS-3-BW_SUM_EXCEEDS_100_PC Sum of bandwidth allocated to all classes exceeds 100 percent. Allocated BW : [dec] percent Explanation Allocated bandiwdth total including the default class can not exceed beyond 100%. Recommended Action Reconfigure policy to assign appropriate bandiwdth guarantees. Error Message %QOS-QOS-3-CHKPT_GET_DATA_FAIL Failed to get QoS init data during restart. Remove policy [chars] from interface [chars], direction [chars] and re-add to recover. Explanation Getting init data from qos ma on RP could fail if there are any issues in restart code path in RP. Recommended Action Remove the policy and add it back Error Message %QOS-QOS-3-CONNECT_FAIL Server connection failed - [chars]. Error code - [chars] Explanation Connection to some server failed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-DEBUG_FAIL Error occurred while registering for debugging services Explanation Error occurred while waiting for an event. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-DEF_CLASS_BW_EXCEED_99_PC Sum of bandwidth allocated to non-default classes exceeds 99 percent. Allocated BW : [dec] percent Explanation Allocated bandiwdth total can not exceed beyond 99% as 1% has to be reserved for the default class. Recommended Action Reconfigure policy to assign appropriate bandiwdth guarantees. Error Message %QOS-QOS-3-DLL_INIT_FAIL Could not initialize [chars] dll. Error code - [chars] Explanation An error was encountered while trying to initialize a DLL that supports a given feature. Both the DLL name and the error code are displayed. This is a critical error in the QOS component. It indicates that the DLL that implements a feature does not provide an initializing function. This indicates that some QOS feature is not working properly. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-EVM_CREATE_FAIL Failed to create event manager Explanation Failed to create event manager. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-FEATURE_ADD_FAIL Failed to add policy [chars], class = [chars], feature = [chars]. Explanation Failed to add the specified feature while applying the specified service policy. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-FILE_ERROR File [chars] error: [chars]. Reason: [chars] Explanation An error was encountered while accessing a file. Both the file name and the error reason are displayed. This is a critical error in the QOS component. It indicates that the file that defines a feature is missing from the system and the related QOS feature will not work properly. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-FILE_WRONG_INFO File [chars] [chars] [dec] Explanation An error was encountered while accessing a file. Both the file name and the error reason are displayed. This is a critical error in the QOS component. It indicates that the file that defines a feature is missing from the system and the related QOS feature will not working properly. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-FT_CONFIGURE_FAIL Failed to configure feature [chars]. Error code - [chars] Explanation The specified feature could not be configured due to the specified reason. Recommended Action Please turn on debugs using the following command: debug qos control all dev Error Message %QOS-QOS-3-FT_REMOVE_FAIL Failed to remove the feature [chars]. Error code - [chars] Explanation The QOS Manager process failed to remove the specified feature. The error code is also displayed. Recommended Action Please turn on debugs using the following command: debug qos control all dev and reenter the configuration command that caused the error. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-FT_SEND_FAIL Sending control to [chars] feature failed Explanation Failed to send a control feature information to the Execution Agent. The name of the feature is displayed. Recommended Action Please turn on debugs using the following command: debug qos control all dev and reenter the configuration command that caused the error. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-MAX_CLASS_EXCEEDED_FOR_FABQOS Policy exceeds number of classes allowed for FabQoS Explanation Fabric QoS policy can only have a maximum of 3 classes. If the number of classes is more than 3, policy map is rejected. Recommended Action Reconfigure policy map to adjust number of classes Error Message %QOS-QOS-3-MGR_DLL_OPEN_FAIL Could not open [chars] DLL. Error code - [chars] Explanation An error was encountered while trying to open a DLL that supports a given feature. Both the DLL name and the error code are displayed. This is a critical error in the QOS component. It indicates that the DLL that implements the feature is not present in the system. This indicates that some QOS feature is not working properly. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-MSG_SEND_FAIL Failed to send message to feature [chars] [chars]. Error code - [chars] Explanation Failed to send the a message to the specified feature due to the error message displayed. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-ONLY_PRI_OR_BW_REM_PERCENT_ALLOWED Can not configure anything other than priority or bandwidth remaining percent for a fabqos policy Explanation Only priority and bandwidth remaining percent commands are supported for FabQoS policy. Recommended Action Reconfigure policy to use these two commands. Error Message %QOS-QOS-3-OVER_SUBSCRIPTION_OF_MIN_BW_GAURANTEES There is oversubscription of minimum bandwidth guarantees, taking HP bandwidth into account. Bandwidth guarantees may not be met for this policy. Allocated BW : [dec] percent Explanation With high priority class configured and the bandwidth guarantee for the HP taken into account, the interface may have been oversubscribed. This could cause some packets from the class that has bandwidth guarantee configured to be dropped. Recommended Action Reconfigure policy to achieve optimal bandwidth guarantee results. Error Message %QOS-QOS-3-POLICY_CHECK_FAIL Failed to configure policy - [chars]. Error code - [chars] Explanation The policy could not be configured on the interface as the policy itself or one of its child policies does not exist. The error code is also displayed. Recommended Action Please turn on debugs using the following command: debug qos control qosmgr dev and reenter the configuration command that caused the error. Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-QFIFO_DEBUG_NETIO_INIT_FAIL Failed to Initialize debug netion - [chars] Error : [chars] Explanation Debug initialization failed for NetIO. Debugs may not be printed. Recommended Action Try restarting qos_ma_ea process. Error Message %QOS-QOS-3-UNSUPPORTED_IP_OR_MPLS_MATCH_CONFIG match on ip or mpls packet fields is not supported on a policy attached to layer2 interface Explanation Matching on layer3 packet fields such as dscp, prec, exp on a service policy attached to an Access Circuit is not supported. Packets received and transmitted on an AC are considered layer2 packets, packet headers beyond L2 are not parsed in the hardware Recommended Action Remove match statements that match on layer3 fields of a packet in the classmaps used by the service policy Error Message %QOS-QOS-3-UNSUPPORTED_L2_MATCH_CONFIG match on mac address is not supported on a policy attached to layer3 interface Explanation Matching on source or destination mac address on a policy attached to layer-3 interfaces such as routed vlan or POS interfaces is not supported Recommended Action Remove invalid match statements in the classmaps used by the service policy Error Message %QOS-QOS-3-UNSUPPORTED_MAC_ADDR_MATCH_CONFIG match on src/dst mac is not supported on output/input l2 service policy Explanation Matching on mac address in an l2 service policy is supported with the following constraints: Match on source mac address is supported only on input l2 service policy Match on destination mac address is supported only on output l2 service policy Recommended Action Remove unsupported match statements in the classmaps used by the service policy Error Message %QOS-QOS-3-UNSUPPORTED_MARKING_CONFIG Invalid marking configuration in service policy attached to layer2 interface Explanation On service policy attached to an AC, marking of certain fields is not supported. The following marking configurations are invalid: Ingress/Egress: ip dscp, ip precedence, mpls exp topmost Egress: mpls exp imposition, qos-group, discard-class Recommended Action Remove invalid 'set' statements from the policymap Error Message %QOS-QOS-3-UNSUPPORTED_MATCH_COS_CONFIG match cos command is not supported on layer-3 interface egress policies. Invalid Configuration. Explanation 'match cos' command is not supported on service policy applied to layer-3 interfaces since layer2 encapsulations are removed before packets are sent to egress. Recommended Action Remove invalid 'match cos' command from class-map Error Message %QOS-QOS-3-UNSUPPORTED_MIN_BW_CONFIG Bandwidth command is not supported on the ingress side. Invalid Configuration. Explanation Bandwidth command is not supported on ingress policies. Instead, configure 'bandwidth remaining' to assign weights for the different queues. Recommended Action Configure policy without 'bandwidth' on the ingress. Error Message %QOS-QOS-3-UNSUPPORTED_MULTIPLE_POLICER_ACTIONS multiple set commands in a policer action are not supported Explanation Only one set command is allowed on each of conform, exceed and violate actions of a policer. Recommended Action Remove multiple set commands on policer conform/exceed/violate action Error Message %QOS-QOS-3-UNSUPPORTED_POLICER_MARKING_CONFIG Invalid policer marking configuration in service policy attached to layer2 interface Explanation On service policy attached to an AC, policer marking of certain fields is not supported. The following policer marking configurations are invalid: Ingress/Egress: ip dscp, ip precedence, mpls exp topmost Egress: mpls exp imposition Recommended Action Remove invalid 'police' statements from the policymap Error Message %QOS-QOS-3-UNSUPPORTED_POLICER_MARKING_L2_COS_CONFIG Invalid policer marking configuration in service policy attached to layer3 interface Explanation On service policy attached to a layer-3 interface, policer marking of layer-2 CoS field is not supported. Recommended Action Remove 'set cos' action on 'police' command from the policymap Error Message %QOS-QOS-3-UNSUPPORTED_POLICER_RATE Unsupported policer value used in policymap : [dec] kbps. It must be less than 16 Gbps Explanation Configured policer value can not be more than 16Gbps. Policy map is rejected. Recommended Action Reconfigure policy map to configure appropriate policer value. Error Message %QOS-QOS-3-UNSUPPORTED_Q_LIMIT_CONFIG In order to configure queue-limit for a class, atleast one feature that allocates a separate queue for that class needs to be configured. Explanation If queue-limit command for a class is configured, then that class requires a separate queue (due to h/w implementation). Since the user has not configured any feature for this class that allocates a separate queue for that class, the user is not allowed to configure queue-limit for that class. Recommended Action Configure policy with a feature which allocates a separate queue. Error Message %QOS-QOS-3-UNSUPPORTED_WRED_CONFIG Invalid wred profile type in service policy attached to layer2 interface Explanation On service policy attached to an AC, valid wred profile types are layer2_cos discard-class and default Recommended Action Remove invalid 'random-detect' statements from the policymap Error Message %QOS-QOS-3-WAIT_ERR Error occurred while waiting for an event Explanation Error occurred while waiting for an event. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-3-WRONG_QUANTAS_SPECIFIED Bandwidth remaining should only be specified in multiples of 5 Explanation Bandwidth remaining commnad has a limitation where the percentages can only be specified in multiples of 5. If not, policy map is rejected. Recommended Action Reconfigure policy to configure quantas in multiples of 5 Error Message %QOS-QOS-4-ERR_EVM_EVENT_BLOCK Unrecoverable error in event loop. Error: [chars] Explanation An error (other than EINTR) occured in the event loop. The process has exited and restarted. Recommended Action If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-4-NODE_INSTL_FAIL Could not install [chars] feature [chars] Explanation An error was encountered while trying to add the specified feature node to NetIO. Both the feature name and the error code are displayed. This is a critical error in the QOS component. It indicates that some QOS feature is not working properly. Recommended Action Please provide the output of the commands: Please provide the output of the commands: show running configuration show qos trace Error Message %QOS-QOS-4-Q_THRESHOLD_EXCEEDS_MAX [chars] Explanation Ingress and egress queuing asics support a maximum packet buffering capacity of 1 Gbytes. Therefore queue-limit or RED thresholds of greater than 1 Gbytes (1073741824 bytes) cannot be configured and will be automatically set to the maximum permissible value. Recommended Action Please re-evaluate the value of queue-limit and/or RED thresholds since it is unlikely that such a high value is necessary. Error Message %QOS-QOS-4-WRED_THRESH_MORE_THAN_QUEUE_LIMIT Min or max threshold for one or more RED profiles of class [chars] is greater than queue limit ([dec] bytes) Explanation Since min or max threshold is greater than queue limit, RED will not take effect or partially take effect for one or more RED profiles of this class. Recommended Action Set RED min and max threshold to be below queue limit. Error Message %QOS-QOS-5-PARENT_HAS_NO_BW_MIN_CONFIGURED Child class bandwidth minimum is reduced to zero due no minimum bandwidth guarantee in parent Explanation Bandwidth command in a child class requires similar command in the parent class. Otherwise minimum bandwidth guaranteed for child class would be zero Recommended Action Reconfigure policy to assign bandwidth guarantee in the parent class before the gaurantee is given to the child class. Error Message %QOS-QOS-6-HPOLICY_ATTACH_FAIL Too many levels of hierarchy in policy [chars]. Explanation The Policy could not be installed because it has more than 2 levels of hierarchy. Recommended Action Simplify the policy-map to include no more than 2 levels of hierarchy. and reapply it. Error Message %QOS-QOS-6-POLICY_ATTACH_FAIL Service policy [chars] could not be attached to [chars]. Error code - [chars] Explanation Policy could not be installed. The reason is displayed. Recommended Action Please verify that the specified policy has been configured with the following command: show running configuration Error Message %QOS-QOS-7-CLASSMAP_NOT_FOUND Class map [chars] not found Explanation The specified class map was not found. Make sure that it is properly configured. If not, please confifure it. Recommended Action Verify that the specified class-map name is properly configured by issuing the following command show running class-map Error Message %QOS-QOS-7-CONNECT_FAIL Server connection failed - [chars]. Error code - [chars] Explanation Connection to IMP server failed during process init. Recommended Action No action is required. Process will be automatically restarted. If not recovered, it is a fatal condition. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. REDUCE Error Message %QOS-QOS-7-DLL_REGISTER_CERR_FAIL Could not register error codes for [chars] dll. Error code - [chars] Explanation Could not get register DLL error codes. This is not a critical error. The QOS Manager will function properly, but will not be able to use any of the debug facilities. Recommended Action None Error Message %QOS-QOS-7-ENS_ERROR ENS Debug:[chars] rc=[chars] Explanation The ENS/NRS infrastructure is not available. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-7-ERR_BAG_REGISTER Failed to register bag structures with bag server (Reason: [chars]) Explanation The process could not register the data structures used by QoS statistics and management agents. This is not a critical error Qos will work properly. However show commands may not work. Recommended Action None Error Message %QOS-QOS-7-ERR_EVM_ASYNC_ATTACH Failed to attach handler for async events: [chars] Explanation Failed to attach handler for async events. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-7-ERR_EVM_CREATE Failed to create event manager Explanation Failed to create event manager. Recommended Action None Error Message %QOS-QOS-7-ERR_EVM_CREATE Failed to create event manager Explanation Failed to create event manager. Recommended Action No action is required. Process will be automatically restarted. If not recovered, it is a fatal condition. If the message recurs, copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. REDUCE Error Message %QOS-QOS-7-ERR_MEM_ALLOC [chars] Explanation The QOS manager process could not get memory for the specified memory usage. This condition will occur if the system is low on memory. Recommended Action None Error Message %QOS-QOS-7-ERR_SYSDB SysDB error [chars]. Error code - [chars] Explanation There were problems communicating with the SysDB. The reason and error message are displayed. If this message is displayed, the qosmgr process will restart itself. Recommended Action None Error Message %QOS-QOS-7-EVENT_CONN_ERR Error in [chars]: [chars] Explanation Error encountered in opening connection to a required server. If this error occurs, the QoS Manager will restart itself. Recommended Action None Error Message %QOS-QOS-7-IM_CONNECT_FAIL Interface control server connection failed - [chars]. Error code - [chars] Explanation Connection to interface manager failed. If this contition occurs, the QOS Manager will restart itself. Recommended Action None Error Message %QOS-QOS-7-NETIO_SET_PAK_SHAPEQ_FAIL Failed to set packet shape Q - [chars] Error : [chars] Explanation Could not set the queue where this packet is supposed to be queued. As a consequence the packet is being dropped. Recommended Action Try removing the policy and reapplying it. Error Message %QOS-QOS-7-OVL_RGST_FAIL Could not register ovl notification handler. Error code - [chars] Explanation An error was encountered while trying to register the OVL notification handler. Recommended Action None Error Message %QOS-QOS-7-POLICY_INSTALL_FAIL Policy could not be installed [chars] [chars] Error code - [chars] Explanation The specified policy could not be attached to an interface due to the specified reason. Recommended Action Copy the error message exactly as it appears on the console or in the system log, call your Cisco technical support representative and provide the representative with the gathered information. Error Message %QOS-QOS-7-POLICY_NOT_FOUND Policy [chars] not found Explanation The specified policy name was not found. Make sure that it is properly configured. If not please configure it. Recommended Action Verify that the specified policy map is properly configured by issuing the following command show running policy-map . Error Message %QOS-QOS-7-POLICY_REMOVE_FAIL Failed to remove policy [chars]. Error= [chars] Explanation The specified policy could not be removed from an interface due to the specified reason. Recommended Action Please follow the instructions from the error message. QOSEA Messages Error Message %QOS-QOSEA-3-ERROR QoSEA-Err: [chars] Explanation This is an error message from the QoS EA Process, it indicates that something has gone wrong internally in the QoS EA. Recommended Action File a DDTS Error Message %QOS-QOSEA-3-MSG_CHAN Could not create Msg chan: [chars] error: [chars] Explanation The QoS EA could not create the necessary message channel due to the given error Recommended Action DDTS Error Message %QOS-QOSEA-3-MSG_HANDLER_ERR An error occurred in the [chars] message handler Explanation An error occurred during message handling in the indicated message handler Recommended Action File a DDTS Error Message %QOS-QOSEA-3-POLICY_ERROR QoSEA-Err: class:[chars], [chars] Explanation This is an error message from the QoS EA Process, it indicates that something has gone wrong while trying to configure a service policy. Recommended Action NONE Error Message %QOS-QOSEA-3-UNHANDLED_MSG The QoS EA received an unhandled message Explanation The QoS EA received a message that it was unable to handle' Recommended Action DDTS Error Message %QOS-QOSEA-3-UNKNOWN_MSG An unknown message was dispatched to the [chars] message handler: Msg: [hex] Explanation An incoming message was demuxed to the incorrect message handler Recommended Action File a DDTS Error Message %QOS-QOSEA-4-WARN QoSEA-Warn: [chars] Explanation This is a warning message from the QoS EA Process Recommended Action RECUR Error Message %QOS-QOSEA-5-NOTICE QoSEA-Notice: [chars] Explanation This is a notice message from the QoS EA Process Recommended Action NONE Error Message %QOS-QOSEA-6-INFO QoSEA-Info: [chars] Explanation This is an informational message from the QoS EA Process Recommended Action RECUR Error Message %QOS-QOSEA-6-MSG_ASYNC An Asynchronous message was received Explanation The QoS EA received an asynchronous message. Recommended Action NONE Error Message %QOS-QOSEA-6-POLICY_INFO QoSEA-Info: class:[chars], [chars] Explanation This is an informational message from the QoS EA Process. It indicates that something can not be configure in service policy. Recommended Action NONE Error Message %QOS-QOSEA-7-DEBUG QoSEA-Debug: [chars] Explanation This is a debuging message from the QoS EA Process Recommended Action NONE QOSRM_DLL Messages Error Message %QOS-QOSRM_DLL-3-ERROR QoSRM-DLL-Err: [chars] Explanation This is an error message from the QoS RM DLL, it indicates that something has gone wrong internally in the QoS RM dll. Recommended Action File a DDTS Error Message %QOS-QOSRM_DLL-3-MSG_CHAN Could not create Msg chan: [chars] error: [chars] Explanation The QoS RM dll could not create the necessary message channel due to the given error Recommended Action DDTS Error Message %QOS-QOSRM_DLL-3-MSG_HANDLER_ERR An error ([chars]) occurred in the [chars] message handler,Msg:[hex] Explanation An error occurred during message handling in the indicated message handler Recommended Action File a DDTS Error Message %QOS-QOSRM_DLL-3-UNHANDLED_MSG The QoS RM dll received an unhandled message Explanation The QoS RM dll received a message that it was unable to handle' Recommended Action DDTS Error Message %QOS-QOSRM_DLL-3-UNKNOWN_MSG An unknown message was dispatched to the [chars] message handler: Msg: [hex] Explanation An incoming message was demuxed to the incorrect message handler Recommended Action File a DDTS Error Message %QOS-QOSRM_DLL-3-UNKNOWN_QTYPE Unknown Q-Type in message: [hex] Explanation The QoS RM dll received a message, but was unable to determine which resource the message was intended for because the Q-Type field was incorrect. Recommended Action File a DDTS Error Message %QOS-QOSRM_DLL-4-WARN QoSRM-DLL-Warn: [chars] Explanation This is a warning message from the QoS RM DLL Recommended Action RECUR Error Message %QOS-QOSRM_DLL-6-INFO QoSRM-DLL-Info: [chars] Explanation This is an informational message from the QoS RM DLL Recommended Action RECUR Error Message %QOS-QOSRM_DLL-6-MSG_ASYNC An Asynchronous message was received Explanation The QoS RM dll received an asynchronous message. Recommended Action NONE Error Message %QOS-QOSRM_DLL-7-DEBUG QoSRM-DLL-Debug: [chars] Explanation This is a debuging message from the QoS RM DLL Recommended Action NONE QOSRM Messages Error Message %QOS-QOSRM-3-ERROR QoSRM-Err: [chars] Explanation This is an error message from the QoS RM Process, it indicates that something has gone wrong internally in the QoS RM. Recommended Action File a DDTS Error Message %QOS-QOSRM-3-MSG_CHAN Could not create Msg chan: [chars] error: [chars] Explanation The QoS RM could not create the necessary message channel due to the given error Recommended Action DDTS Error Message %QOS-QOSRM-3-MSG_HANDLER_ERR Event: [chars] occurred in the [chars] message handler, Msg:[hex] Explanation An error occurred during message handling in the indicated message handler Recommended Action File a DDTS Error Message %QOS-QOSRM-3-UNHANDLED_MSG The QoS RM received an unhandled message Explanation The QoS RM received a message that it was unable to handle' Recommended Action DDTS Error Message %QOS-QOSRM-3-UNKNOWN_MSG An unknown message was dispatched to the [chars] message handler: Msg: [hex] Explanation An incoming message was demuxed to the incorrect message handler Recommended Action File a DDTS Error Message %QOS-QOSRM-3-UNKNOWN_QTYPE Unknown Q-Type in message: [hex] Explanation The QoS RM received a message, but was unable to determine which resource the message was intended for because the Q-Type field was incorrect. Recommended Action File a DDTS Error Message %QOS-QOSRM-4-WARN QoSRM-Warn: [chars] Explanation This is a warning message from the QoS RM Process Recommended Action RECUR Error Message %QOS-QOSRM-6-INFO QoSRM-Info: [chars] Explanation This is an informational message from the QoS RM Process Recommended Action RECUR Error Message %QOS-QOSRM-6-MSG_ASYNC An Asynchronous message was received Explanation The QoS RM received an asynchronous message. Recommended Action NONE Error Message %QOS-QOSRM-7-DEBUG QoSRM-Debug: [chars] Explanation This is a debuging message from the QoS RM Process Recommended Action NONE
	© 1992-2008 Cisco Systems, Inc. All rights reserved. Terms & Conditions \| Privacy Statement \| Cookie Policy \| Trademarks of Cisco Systems, Inc.