This guide lists TL1 commands and autonomous messages by category. It includes basic descriptions and input and output formats supported by the Cisco ONS 15454 SDH, Release 5.0. Refer to the Cisco ONS 15454 SDH TL1 Command Guide, Release 5.0 for a complete description of TL1 commands.
TL1 commands conform to the following syntax: a:b:c:d:e: ...z; where: "a" is the Command Code "b" is the Target Identifier (TID) "c" is the Access Identifier (AID) or the User Identifier (UID) "d" is the Correlation Tag (CTAG) "e: ...z;" are other positions required for various commands The TID, AID, and CTAG route and control the TL1 command. Other parameters provide additional information required to complete the action requested by the command.
1 MS-SPRing
Table 1 MS-SPRing
DLT-<MOD_RING>:[<TID>]:<AID>:<CTAG>[:::];
Deletes the multiplex section-shared protection ring (MS-SPRing) of the NE.
Exercises the algorithm for switching from a working facility to a protection facility without actually performed a switch.
RTRV-<MOD_RING>:[<TID>]:[<AID>]:<CTAG>[::::];
Retrieves all of the MS-SPRing information of the network element (NE).
Output format:
SID DATE TIME M CTAG COMPLD "[<AID>]::[RINGID=<RINGID>,][NODEID=<NODEID>,][MODE=<MODE>,] [RVRTV=<RVRTV>,][RVTM=<RVTM>,][SRVRTV=<SRVRTV>,][SRVTM=<SRVTM>,] [EASTWORK=<EASTWORK>,][WESTWORK=<WESTWORK>,][EASTPROT=<EASTPROT>,] [WESTPROT=<WESTPROT>]" ;
RTRV-TRC-<STM_MSSPR>:[<TID>]:<AID>:<CTAG>;
Retrieves the valid J1 expected trace string, received trace string, trace mode, c2 byte, VC bandwidth of the STM port only if the port has MS-SPring.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[LEVEL=<LEVEL>,][EXPTRC=<EXPTRC>,][INCTRC=<INCTRC>,] [TRCMODE=<TRCMODE>,][C2=<C2>]"
Permit the NE's APC application to force regulation of the optical power to the DWDM ring.
OPR-LASER-OTS:[<TID>]:<AID>:<CTAG>;
Instructs a laser to be switched on.
OPR-LNK:[<TID>]::<CTAG>;
Permits the NE's optical link (OLNK) application to calculate all automatic optical links between points that can be univocally identified by the NE.
OPR-PROTNSW-OCH:[<TID>]:<AID>:<CTAG>::<SW>;
Performs a protection switch on the trunk port of a TXPP_MR_2.5G transponder (protect version only).
OPR-SLV-WDMANS:[<TID>]:<AID>:<CTAG>;
Invokes the calculation of the expected span loss verification.
OPR-WDMANS:[<TID>]::<CTAG>;
Permits the NE's AONS application to force a recompute of the value assigned to all variable optical attenuators (VOAs) representing the optical path inside the node.
SID DATE TIME M CTAG COMPLD "<AID>,<MOD>:<CONDTYPE>,,,<THLEVEL>" ;
RTRV-APC:[<TID>]::<CTAG>;
Retrieves the NE's APC application attributes.
Output format:
SID DATE TIME M CTAG COMPLD "::[APCENABLE=<APCENABLE>,][APCSTATE=<APCSTATE>]" ;
RTRV-DWDM:[<TID>]:<AID>:<CTAG>;
Retrieves DWDM card-level attributes.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<EQPTTYPE>,<EQUIP>,,[<STATUS>]:[PEERID=<PEERID>,][NAME=<NAME>,] [TERMMODE=<TERMMODE>,][PAYLOAD=<PAYLOAD>,] [CARDNAME=<CARDNAME>,][PWL=<PWL>,][TWL1=<TWL>,][TWL2=<TWL1>,] [TWL3=<TWL2>,][TWL4=<TWL3>]:<PST_PSTQ>,[<SSTQ>]" ;
Retrieves any optical link associated with the entered AID(s) or AID range.
Output format:
SID DATE TIME M CTAG COMPLD "<FROM>,<TO>::[OLNKT=<OPTICALLINKTYPE>,][CTYPE=<CREATIONTYPE>,] [RDIRN=<RDIRN>,][BAND=<BAND>,][WLEN=<WLEN>]:<PST_PSTQ>,[<SST>]" ;
RTRV-NE-APC:[<TID>]:[<AID>]:<CTAG>;
Retrieves the NE's APC application ports involved in node setup regulation.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>,<MOD>::[MODIFDAT=<MODIFDAT>,][MODIFTM=<MODIFTM>,] [CHECKDAT=<CHECKDAT>,][CHECKTM=<CHECKTM>]" ;
RTRV-NE-WDMANS:[<TID>]::<CTAG>;
Retrieves the NE's optical node setup (WDMANS) application ports involved in node setup regulation.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>,<AIDTYPE>::[REGULATED=<REGULATED>,][PARAM=<PARAM>]"
;
RTRV-OCH:[<TID>]:<AID>:<CTAG>;
Retrieves the attributes (that is, service parameters) and state of an OCH facility.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>:,,[<ROLE>],[<STATUS>]:[RDIRN=<RDIRN>,][OPTYPE=<OPTICALPORTTYPE>,] [OPWR=<POWER>,][EXPWLEN=<EXPWLEN>,][ACTWLEN=<ACTWLEN>,] [ILOSS=<ILOSS>,][VOAMODE=<VOAMODE>,][VOAATTN=<VOAATTN>,] [VOAPWR=<VOAPWR>,][VOAREFATTN=<VOAREFATTN>,] [VOAREFPWR=<VOAREFPWR>,][REFOPWR=<REFOPWR>,][CALOPWR=<CALOPWR>,] [CHPOWER=<CHPOWER>,][NAME=<PORTNAME>,][SFBER=<SFBER>,] [SDBER=<SDBER>,][COMM=<COMM>,][GCCRATE=<GCCRATE>,][DWRAP=<DWRAP>,] [FEC=<FEC>,][PAYLOADMAP=<PAYLOADMAP>,][OSFBER=<OSFBER>,] [OSDBER=<OSDBER>,][MACADDR=<MACADDR>,][SYNCMSG=<SYNCMSG>,] [SENDDUS=<SENDDUS>,][SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>,][OSPF=<OSPF>,] [LBCL=<LBCL>,][OPT=<OPT>,][OPR=<OPR>]:<PST_PSTQ>,[<SSTQ>]" ;
RTRV-OMS:[<TID>]:<AID>:<CTAG>;
Retrieves the attributes (that is, service parameters) and state of an OMS facility.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::RDIRN=<RDIRN>,OPTYPE=<OPTICALPORTTYPE>,[OPWR=<POWER>,] EXPBAND=<EXPBAND>,[ACTBAND=<ACTBAND>,][ILOSS=<ILOSS>,] [VOAMODE=<VOAMODE>,][VOAATTN=<VOAATTN>,][VOAPWR=<VOAPWR>,] [VOAREFATTN=<VOAREFATTN>,][VOAREFPWR=<VOAREFPWR>,] [REFOPWR=<REFOPWR>,][CALOPWR=<CALOPWR>,][CHPOWER=<CHPOWER>,] [NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>]" ;
RTRV-OPM:[<TID>]:<AID>:<CTAG>;
Retrieves the optical power monitoring parameters present at the OCH layer in a reconfigurable optical add/drop multiplexing (ROADM) node.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[POWEROUT=<POWEROUT>,][POWERADD=<POWERADD>,] [POWERPT=<POWERPT>]" ;
RTRV-OSC:[<TID>]:<AID>:<CTAG>;
Retrieves all OSC information of the NE.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[RINGID=<RINGID>,][NODEID=<NODEID>,][EAST=<EAST>,][WEST=<WEST>]" ;
RTRV-OTS:[<TID>]:<AID>:<CTAG>;
Retrieves the attributes (that is, service parameters) and state of an OTS facility.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>:RDIRN=<RDIRN>,OPTYPE=<OPTICALPORTTYPE>,[OPWR=<POWER>,] [ILOSS=<ILOSS>,][VOAMODE=<VOAMODE>,][VOAATTN=<VOAATTN>,] [VOAPWR=<VOAPWR>,][VOAREFATTN=<VOAREFATTN>,] [VOAREFPWR=<VOAREFPWR>,][OSRI=<OSRI>,][AMPLMODE=<AMPLMODE>,] [CHPOWER=<CHPOWER>,][GAIN=<GAIN>,][EXPGAIN=<EXPGAIN>,] [REFOPWR=<REFOPWR>,][OFFSET=<OFFSET>,][REFTILT=<REFTILT>,] [CALTILT=<CALTILT>,][ASEOPWR=<ASEOPWR>,][DCULOSS=<DCULOSS>,] [AWGST=<AWGST>,][HEATST=<HEATST>,][NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>]" ;
RTRV-PROTNSW-OCH:[<TID>]:<AID>:<CTAG>;
Retrieves the protection switch status of a TXPP_MR_2.5G transponder trunk port (protect version only).
Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<SW>,<SWTYPE>" ;
RTRV-SLV-WDMANS:[<TID>]:<AID>:<CTAG>;
Retrieves the options provisionable by the ED-SLV-WDMASN command.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[HIGHSLVEXP=<HIGHSLVEXP>,][LOWSLVEXP=<LOWSLVEXP>,] [SLVACT=<SLVACT>,][RESOLUTION=<RESOLUTION>]" ;
SID DATE TIME M CTAG COMPLD "<CHANNEL>,<MOD>::[TRCLEVEL=<TRCLEVEL>,][EXPTRC=<EXPTRC>,] [TRC=<TRC>,][INCTRC=<INCTRC>,][TRCMODE=<TRCMODE>,] [TRCFORMAT=<TRCFORMAT>]" ;
RTRV-WDMANS:[<TID>]:<AID>:<CTAG>;
Retrieves the AONS application attributes.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[POWERIN=<POWERIN>,][POWEROUT=<POWEROUT>,] [POWEREXP=<POWEREXP>,][NTWTYPE=<NTWTYPE>,] [OPTICALTYPE=<OPTICALTYPE>,][LASTRUNDAT=<LASTRUNDAT>,] [LASTRUNTM=<LASTRUNTM>]" ;
RTRV-WLEN:[<TID>]:<aid>:<CTAG>;
Retrieves the WLEN provisioning information.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<CCT>:[SIZE=<SIZE>,][CKTID=<CKTID>]:<PST_PSTQ>,[<SSTQ>]" ;
Sets the alarm thresholds on the following cards/ports/channels: MXP_2.5G_10G/TXP_MR_10G, optical service channel, optical amplifier, dispersion compensation units, multiplex/demultiplex and OADM.
4 Environment
Table 4 Environment
OPR-ACO-ALL:[<TID>]::<CTAG>; Operates the cut-off of the office audible alarm indications without changing the local alarm indications.
SID DATE TIME M CTAG COMPLD "<AID>,[<AIDTYPE>]:[<NTFCNCDE>],<TYPEREP>,[<SRVEFF>],[<OCRDAT>], [<OCRTM>],,,[<DESC>]" ;
RTRV-EQPT:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the data parameters and state parameters associated for an equipment unit.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<AIDTYPE>,<EQUIP>,[<ROLE>],[<STATUS>]:[PROTID=<PROTID>,] [PRTYPE=<PRTYPE>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,] [CARDNAME=<CARDNAME>,][IOSCFG=<IOSCFG>,][CARDMODE=<CARDMODE>,] [PEERID=<PEERID>,][REGENNAME=<REGENNAME>,][PWL=<PWL>]:<PST_PSTQ>, <SSTQ>" ;
Uploads startup Cisco IOS configuration files from the network to the node and downloads startup Cisco IOS configuration files from the node to the network (ML-Series Ethernet cards).
Reports changes on the NE that result from TL1 provisioning commands or their graphical user interface (GUI) equivalents or an external event such as a board insertion.
Output format:
SID DATE TIME A ATAG REPT DBCHG "TIME=<TIME>,DATE=<DATE>,[SOURCE=<SOURCE>,][USERID=<USERID>,] DBCHGSEQ=<DBCHGSEQ>:<COMMAND>:[<AID>]:::[<PSTPSTQ>,]<SST>" ;
RTRV-LOG:[<TID>]::<CTAG>::<LOGNM>;
Retrieves the alarm log of the NE.
10 Network
Table 10 Network
RTRV-MAP-NETWORK:[<TID>]::<CTAG>;
Reports all the NE attributes that are reachable from the gateway NE (GNE).
RTRV-NE-IPMAP:[<TID>]:[<AID>]:<CTAG>;
Retrieves the IP address and node name of the NEs that have the data communications channel (DCC) connection with this NE.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<IPADDR>,<NODENAME>" ;
Retrieves the attributes associated with an SDH high/low order path.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[LEVEL=<LEVEL>,][SFBER=<SFBER>,][SDBER=<SDBER>,][RVRTV=<RVRTV>,] [RVTM=<RVTM>,][SWPDIP=<SWPDIP>,][HOLDOFFTIMER=<HOLDOFFTIMER>,] [EXPTRC=<EXPTRC>,][TRC=<TRC>,][INCTRC=<INCTRC>,][TRCMODE=<TRCMODE>,] [TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][SNCPPTHSTATE=<SNCPPTHSTATE>,] [C2=<C2>,][MSSPRPTHSTATE=<MSSPRPTHSTATE>]:<PST_PSTQ>,[<SSTQ>]" ;
RTRV-VT:[<TID>]:<AID>:<CTAG>;
Retrieves the attributes associated with a VT path based on the granularity level of NE/slot/specific VTs.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[LEVEL=<LEVEL>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,] [HOLDOFFTIMER=<HOLDOFFTIMER>,][TACC=<TACC>,][TAPTYPE=<TAPTYPE>,] [SNCPPTHSTATE=<SNCPPTHSTATE>]:[<PST>[,<SST>]]" ;
12 Performance
Table 12 Performance
ALW-PMREPT-ALL:[<TID>]::<CTAG>; Resumes the processing of all performance monitoring (PM) reports that are inhibited.
Sets the thresholds for PMs and the alarm thresholds for a MXP_2.5G_10G/TXP_MR_10G card facility; if used to set alarm thresholds, the time period (tmper) is not applicable.
Modifies the attributes and the state of the STM1E port facility.
ENT-<MOD1PAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];
Creates the specified port.
OPR-ALS:[<TID>]:<AID>:<CTAG>[::::];
Restarts the laser of an STM facility.
RTRV-<MOD1FCPAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the attributes related with the Fibre Channel (FC) port.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::LINKRATE=<LINKRATE>,LINKSTATE=<LINKSTATE>, [LINKRCVRY=<LINKRCVRY>,][DISTEXTN=<DISTEXTN>,] [LINKCREDITS=<LINKCREDITS>,][MFS=<MFS>,][ENCAP=<ENCAP>,][NAME=<NAME>,] [SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>]:<PST_PSTQ>,[<SST>]" ;
RTRV-<MOD1FICONPAYLOAD>:[<TID>]:<AID>:<CTAG>;
Returns Fibre Channel specific settings for ports that have been configured to carry FICON traffic using the ENT-FICON command.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[LINKRATE=<LINKRATE>,][LINKSTATE=<LINKSTATE>,] [LINKRCVRY=<LINKRCVRY>,][DISTEXTN=<DISTEXTN>,] [LINKCREDITS=<LINKCREDITS>,][MFS=<MFS>,][ENCAP=<ENCAP>,] [NAME=<NAME>,][SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>]:<PST_PSTQ>,<SST>" ;
RTRV-<STM_TYPE>:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the attributes (that is, service parameters) and state of an STM facility.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>:,,[<ROLE>],[<STATUS>]:[DCC=<DCC>,][AREA=<AREA>,][TMGREF=<TMGREF>,] [SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,][PJMON=<PJMON>,] [SFBER=<SFBER>,][SDBER=<SDBER>,][MODE=<MODE>,][WVLEN=<WVLEN>,] [RINGID=<RINGID>,][MSSPRTYPE=<MSSPRTYPE>,][MUX=<MUX>,][UNIC=<UNIC>,] [CCID=<CCID>,][NBRIX=<NBRIX>,][SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>,] [SSMRCV=<SSMRCV>,][OSPF=<OSPF>,][LDCC=<LDCC>,][NAME=<NAME>,] [LBCL=<LBCL>,][OPT=<OPT>,][OPR=<OPR>,][EXPTRC=<EXPTRC>,][TRC=<TRC>,] [TRCMODE=<TRCMODE>,][TRCFORMAT=<TRCFORMAT>,][ADMSSM=<ADMSSM>,] [SENDDUSFF=<SENDDUSFF>,][AISONLPBK=<AISONLPBK>]:<PST_PSTQ>,[<SSTQ>]" ;
RTRV-10GIGE:[<TID>]:<AID>:<CTAG>[::::];
Used to retrieve the 10-Gbps-specific parameters for a port configured to support the gigabyte Ethernet payload using the ENT-10GIGE command.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[NAME=<NAME>,][MACADDR=<MACADDR>,][LBCL=<LBCL>,] [OPT=<OPT>,][OPR=<OPR>]:<PST_PSTQ>,[<SST>]" ;
RTRV-ALS:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the ALS attributes of an STM facility and in general for all facilities that support the ALS feature.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>,<AIDTYPE>::[ALSMODE=<ALSMODE>,][ALSRCINT=<ALSRCINT>,] [ALSRCPW=<ALSRCPW>,][LSRSTAT=<LSRSTAT>]" ;
RTRV-DS3I:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the properties of a DS3i-N-12 facility.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::FMT=<FMT>,LINECDE=<LINECDE>,LBO=<LBO>,[INHFELPBK=<INHFELPBK>,] [TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][SFBER=<SFBER>,][SDBER=<SDBER>,] [SOAK=<SOAK>,][NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>]" ;
RTRV-E1:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the attributes and state information of an E1 port facility.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::LINECDE=<LINECDE>,FMT=<FMT>,[TACC=<TACC>,] [TAPTYPE=<TAPTYPE>,][SFBER=<SFBER>,][SDBER=<SDBER>,][SOAK=<SOAK>,] [NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>]" ;
RTRV-E3:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the attributes and state information of an E3 port facility.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[TACC=<TACC>,][TAPTYPE=<TAPTYPE>,][SFBER=<SFBER>,] [SDBER=<SDBER>,][SOAK=<SOAK>,][NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>]" ;
RTRV-E4:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the attributes and state information of an E4 port facility.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[PAYLOAD=<PAYLOAD>,][SFBER=<SFBER>,][SDBER=<SDBER>,] [SOAK=<SOAK>,][NAME=<NAME>]:<PST_PSTQ>,[<SSTQ>]" ;
RTRV-ESCON:[<TID>]:<AID>:<CTAG>;
Retrieves Fibre Channel specific settings for ports that have been configured to carry ESCON traffic using the ENT-ESCON command.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[ENCAP=<ENCAP>]" ;
RTRV-FAC:[<TID>]:<SRC>:<CTAG>[::::];
Retrieves the payload type of the facility.
Output format:
SID DATE TIME M CTAG COMPLD "<SRC>::PAYLOAD=<PAYLOAD>:<PST_PSTQ>,[<SSTQ>]" ;
RTRV-FSTE:[<TID>]:<AID>:<CTAG>;
Retrieves the front end port information of a Fast Ethernet (10/100 Mbps) card.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[ADMINSTATE=<ADMINSTATE>,][LINKSTATE=<LINKSTATE>,] [MTU=<MTU>,][FLOWCTRL=<FLOWCTRL>,][DUPLEX=<DUPLEX>,][SPEED=<SPEED>,] [FLOW=<FLOW>,][EXPDUPLEX=<EXPDUPLEX>,][EXPSPEED=<EXPSPEED>,] [VLANCOS=<VLANCOS>,][IPTOS=<IPTOS>,][NAME=<NAME>,][SOAK=<SOAK>,] [SOAKLEFT=<SOAKLEFT>]:<PST_PSTQ>,[<SSTQ>]" ;
RTRV-G1000:[<TID>]:<AID>:<CTAG>;
Retrieves the G1000 facilities configuration.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[MFS=<MFS>,][FLOW=<FLOW>,][LAN=<LAN>,][OPTICS=<OPTICS>,] [TRANS=<TRANS>,][TPORT=<TPORT>,][LOWMRK=<LOWMRK>,] [HIWMRK=<HIWMRK>,][AUTONEG=<AUTONEG>,][ENCAP=<ENCAP>,] [NAME=<NAME>,][SOAK=<SOAK>,][SOAKLEFT=<SOAKLEFT>]:<PST_PSTQ>,[<SSTQ>]" ;
RTRV-GFP:[<TID>]:<SRC>:<CTAG>;
Retrieves GFP; used for GFP management.
Output format:
SID DATE TIME
M CTAG COMPLD "<AID>::[FCS=<FCS>,][AUTOTHGFPBUF=<AUTOTHGFPBUF>,][GFPBUF=<GFPBUF>,] [FILTER=<FILTER>]" ;
RTRV-GIGE:[<TID>]:<AID>:<CTAG>;
Retrieves front end port information of a 1 Gigabit Ethernet card.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[ADMINSTATE=<ADMINSTATE>,][LINKSTATE=<LINKSTATE>,] [MTU=<MTU>,][ENCAP=<ENCAP>,][FLOWCTRL=<FLOWCTRL>,] [OPTICS=<OPTICS>,][DUPLEX=<DUPLEX>,][SPEED=<SPEED>,][NAME=<NAME>]" ;
RTRV-POS:[<TID>]:<AID>:<CTAG>;
Retrieves the back-end port information for the Ethernet card, when the back-end port is working in POS mode.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[ADMINSTATE=<ADMINSTATE>,][LINKSTATE=<LINKSTATE>,] [MTU=<MTU>,][ENCAP=<ENCAP>,][NAME=<NAME>,][SOAK=<SOAK>,] [SOAKLEFT=<SOAKLEFT>]:<PST_PSTQ>,[<SST>]" ;
RTRV-STM1E:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the attributes and state information of an STM1E facility.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>::[PAYLOAD=<PAYLOAD>,][SYNCMSG=<SYNCMSG>,][SENDDUS=<SENDDUS>,] [SFBER=<SFBER>,][SDBER=<SDBER>,][SOAK=<SOAK>,][NAME=<NAME>]:<PST_PSTQ>, [<SSTQ>]" ;
Instructs an SDH NE to release (clear) an SDH line protection switch request.
RLS-PROTNSW-<PATH>:[<TID>]:<SRC>:<CTAG>[::];
Instructs an SDH NE to release (clear) an SDH path protection switch request that was established with the OPR-PROTNSW-(MOD_PATH) command.
RTRV-FFP-<STM_TYPE>:[<TID>]:<AID>:<CTAG>[::::];
Retrieves the optical facility protection information.
Output format:
SID DATE TIME M CTAG COMPLD "<WORK>,<PROTECT>::[PROTID=<PROTID>,][RVRTV=<RVRTV>,][RVTM=<RVTM>,] [PSDIRN=<PSDIRN>,][VRGRDTM=<VRGRDTM>,][DTGRDTM=<DTGRDTM>,] [RCGRDTM=<RCGRDTM>,][OPOTYPE=<OPOTYPE>]" ;
Adds a user account; can only be performed by a Superuser.
INH-MSG-SECU:[<TID>]::<CTAG>;
Disables the REPT EVT SECU and REPT ALM SECU autonomous messages.
INH-USER-SECU:[<TID>]::<CTAG>::<UID>;
Disables (without deleting) a user account so the user is denied access to the NE.
REPT ALM SECU
Reports the occurrence of an alarmed security event against the NE.
Output format:
SID DATE TIME ** ATAG REPT ALM SECU "<AID>:<NOTIFCODE>,<SECUALMTYPE>" ;
REPT EVT SECU
Reports the occurrence of a non-alarmed user or system security event against the NE.
Output format:
SID DATE TIME A ATAG REPT EVT SECU "<AID>:<DNFIELD>,[<CONDEFF>],,,,,,,:<SECURITY>:<DNFIELD1>" ;
REPT EVT SESSION
Reports a non-alarmed event related to establishing a session with the NE.
Output format:
SID DATE TIME A ATAG REPT EVT SESSION "<AID>:<EXP>,<PCN>" "<WARN>" ;
RTRV-CMD-SECU:[<TID>]:<AID>:<CTAG>;
Retrieves the current command security level of the command specified in the AID field.
Output format:
SID DATE TIME M CTAG COMPLD "<AID>:<CAP>" ;
RTRV-DFLT-SECU:[<TID>]:<AID>:<CTAG>;
Retrieves default security information; used by an administrator to retrieve the system-wide default values associated with several security parameters.
Output format:
SID DATE TIME M CTAG COMPLD "<NE>:PAGE=<PAGE>,PCND=<PCND>,MXINV=<MXINV>,DURAL=<DURAL>, TMOUT=<TMOUT>,UOUT=<UOUT>,PFRCD=<PFRCD>,POLD=<POLD>,PINT=<PINT>, LOGIN=<LOGIN>,PRIVLVL=<UAP>" ;
RTRV-USER-SECU:[<TID>]:<UID>:<CTAG>;
Retrieve user security; retrieves the security information of a specified user or list of users.
Output format:
SID DATE TIME M CTAG COMPLD "<UID>:,<PRIVILEGE>:LOGGEDIN=<LOGGEDIN>,[NUMSESSIONS=<NUMSESS>,] [LOCKEDOUT=<LOCKEDOUT>,][DISABLED=<DISABLED>]" ;
Forces the NE to switch to the reference specified by the synchronization reference number if the reference supplied is valid and of the same quality; otherwise the command will fail.
