Table Of Contents
Guide to Supported Hardware for Cisco 7600 Series Routers with Cisco IOS Release 12.2SR
Contents
Document Revision History
Supported Hardware
Supervisor Engines
Supervisor Engine 720
Supervisor Engine 32
Route Switching Processor 720
Policy Feature Cards
Policy Feature Card Guidelines and Restrictions
Policy Feature Card 3BXL
Policy Feature Card 3B
Policy Feature Card 3C
Policy Feature Card 3CXL
Distributed and Centralized Forwarding Cards
Centralized Forwarding Card (WS-X6700-CFC)
Distributed Forwarding Card 3BXL
Distributed Forwarding Card 3B
Distributed Forwarding Card 3CXL
Distributed Forwarding Card 3C
10-Gigabit Ethernet Switching Modules
XENPAKs
X2 Modules
Gigabit Ethernet Switching Modules
Small Form-Factor Pluggable Modules (SFPs)
Gigabit Ethernet SFPs
Fast Ethernet SFPs
10-Gigabit Ethernet Transceiver Modules
DWDM-XFP Modules
Gigabit Interface Converters (GBICs)
Power over Ethernet Daughtercards
10/100/1000 Ethernet Switching Modules
Fast Ethernet Switching Modules
Ethernet/Fast Ethernet (10/100) Switching Modules
Ethernet Switching Modules
Optical Services Modules (OSMs)
OSM Guidelines and Restrictions
Gigabit Ethernet WAN
OC-48 Packet over SONET
OC-48 DPT/Packet over SONET
OC-12 Packet over SONET
OC-3 Packet over SONET
OC-12 Channelized
CT3/T1 Channelized/Unchannelized
OC-12 ATM
SPA Interface Processors (SIPs)
SIP-400 Combinations
Shared Port Adapters (SPAs)
Ethernet SPAs
Fast Ethernet SPAs
POS SPAs
ATM SPAs
Serial SPAs
Circuit Emulation over Packet (CEoP) SPAs
Services SPA Carrier (SSC)
Services SPAs
Enhanced FlexWAN Module
Enhanced FlexWAN Module Port Adapters
Ethernet Services 20G Line Cards
Ethernet Services 40G Line Cards
Service Modules
Anomaly Guard Module
Traffic Anomaly Detector Module
Persistent Storage Device (PSD) Module
Multi-Processor WAN Application Module (MWAM)
Content Services Gateway (CSG) Module
Firewall Services Module
Intrusion Detection System Modules (IDSMs)
Network Analysis Modules (NAMs)
Application Control Engine (ACE) Module
Service Application Module for IP
Wireless Services Module (WiSM)
Fan Trays
High-Capacity Fan Trays
Power Supplies
CISCO7606 Power Supplies
CISCO7606-S Power Supplies
WS-C6504-E and CISCO7604 Power Supplies
WS-C6503, WS-C6503-E, and CISCO7603 Power Supplies
CISCO7603-S Power Supplies
All Other Power Supplies
Chassis
13-Slot Chassis
9-Slot Chassis
6-Slot Chassis
4-Slot Chassis
3-Slot Chassis
Unsupported Hardware
Unsupported Service Modules
Unsupported Port Adapters
Unsupported Supervisor Engines
Unsupported Policy Feature Cards and Distributed Forwarding Cards
Unsupported Line Cards
Unsupported Service Modules
Unsupported Chassis
Unsupported Power Supplies
Related Documentation
Cisco.com
Product Documentation DVD
Ordering Documentation
Documentation Feedback
Cisco Product Security Overview
Reporting Security Problems in Cisco Products
Product Alerts and Field Notices
Obtaining Technical Assistance
Cisco Support Website
Submitting a Service Request
Definitions of Service Request Severity
Obtaining Additional Publications and Information
Guide to Supported Hardware for Cisco 7600 Series Routers with Cisco IOS Release 12.2SR
This publication lists the supported hardware for Cisco 7600 series routers with Cisco IOS Release 12.2SR.
Use this publication with the Cross-Platform Release Notes for Cisco IOS Release 12.2SR.
Contents
This publication contains these sections:
•
Document Revision History
•Supported Hardware
•Unsupported Hardware
•Related Documentation
•Obtaining Documentation
•Documentation Feedback
•Cisco Product Security Overview
•Product Alerts and Field Notices
•Obtaining Technical Assistance
•Obtaining Additional Publications and Information
Document Revision History
Revision
|
Date
|
Change Summary
|
OL-10362-7
|
October, 2008
|
Added the following for Cisco IOS release 12.2(33)SRD:
•7600-ES+2TGCXL
•7600-ES+2TG3C
•7600-ES+4TGCXL
•7600-ES+4TG3C
•7600-ES+40G3C
•7600-ES+20G3CXL
•7600-ES+20G3C
•7600-ES+40G3CXL
•CWDM SFP Support
•DWDM SFP Support
•XFP-10GER-OC192IR= Version 2 XFP support
•SFP-GE-T= with ES40 Line Card Support
•XFP-10GZR-OC192LR+= XFP Support
•support BX optics (GLC-BX-U=, GLC-BX-D=) with GE SPA (SIP line cards), ES20 & ES40 line cards
•DWDM XFP support
•SPA-8X1FE-TX-V2 and SPA-4X1FE-TX-V2 Support on SIP-400
•Network Analysis Modules (NAMs) Support for RSP720-10GE
|
OL-10362-6
|
May, 2008
|
Added the following for Cisco IOS release 12.2(33)SRC1:
•SPA-4XT-Serial SPA support on SIP-200
•Additional DWDM XFP support for ES20 line card, SIP-400, and SIP-600
|
OL-10362-5
|
April, 2008
|
Added the following for Cisco IOS release 12.2(33)SRB3:
•DWDM XFP support on Cisco 7600 ES20 line card and SIP-600
•SFP-GE-T support on Cisco 7600 ES20 line card, SIP-400, and SIP-600
•CWDM SFP support on Cisco 7600 ES20 line card
|
OL-10362-4
|
January, 2008
|
Added the following for Cisco IOS release 12.2(33)SRC:
•SPA-2CHT3-CE-ATM on SIP-400
•WS-X6708-10G-3C, WS-X6708-10G-3CXL
•RSP720-3C-10GE, RSP720-3CXL-10GE
•SPA-1X10GE-L-V2 on the SIP-400
•SPA-1xCHSTM1/OC3 on the SIP-400
•SFP-GE-T Support on the SIP-400, SIP-600, and Ethernet Services 20G line cards
•SPA-2XCT3/DS0, SPA-4XCT3/DS0 support on SIP-400
•SPA-8XCHT1/E1 on the SIP-400
•SPA-2XT3/E3, SPA-4XT3/E3 support on SIP-400
•Wireless Services Module (WiSM)
|
OL-10362-3
|
June, 2007
|
Added the following for Cisco IOS release 12.2(33)SRB1:
•Cisco 7606-S router chassis
•Cisco 7603-S router chassis
•1500 W DC input (PWR-1500-DC) power supply
•XFP-10GZR-OC192LR Gigabit Ethernet Transceiver Module
•Cisco 7600 Series ACE 20 HW for Session Border Controller
|
OL-10362-2
|
February, 2007
|
Added the following for Cisco IOS release 12.2SRB:
•RSP 720
•Policy Feature Card 3C
•Policy Feature Card 3CXL
•Distributed Forwarding Card 3CXL
•SFP-GE-S, SFP-GE-L, SFP-GE-Z
•1-Port and 24-Port Channelized CEoP SPAs
•Ethernet Services 20G line cards
•Application Control Engine (ACE) Module
•Service Application Module for IP
•6000 W DC power supply
•Cisco 7609-S router chassis
|
OL-10362-1
|
May, 2006
|
Initial version
|
Supported Hardware
These sections describe the hardware supported in Cisco IOS Release 12.2SR:
•Supervisor Engines
•RSP720-3C-10GE
•Distributed and Centralized Forwarding Cards
•XENPAKs
•X2 Modules
•Small Form-Factor Pluggable Modules (SFPs)
•10-Gigabit Ethernet Transceiver Modules
•DWDM-XFP Modules
•Power over Ethernet Daughtercards
•10/100/1000 Ethernet Switching Modules
•Fast Ethernet Switching Modules
•Ethernet/Fast Ethernet (10/100) Switching Modules
•Ethernet Switching Modules
•Optical Services Modules (OSMs)
•SPA Interface Processors (SIPs)
•SIP-400 Combinations
•Services SPA Carrier (SSC)
•Services SPAs
•Enhanced FlexWAN Module
•Enhanced FlexWAN Module Port Adapters
•Ethernet Services 20G Line Cards
•Ethernet Services 40G Line Cards
•Service Modules
•Fan Trays
•Power Supplies
•Chassis
Note•Use the values in the "Power Required" column to determine the exact power requirements for your configuration to ensure that you are within the power budget.
•Daughtercard power is shown separately.
•Enter the show power command to display current system power usage.
Supervisor Engines
•Supervisor Engine 720
•Supervisor Engine 32
•Route Switching Processor 720
Supervisor Engine 720
•Supervisor Engine 720 Common Features
•Supervisor Engine 720 with PFC3BXL
•Supervisor Engine 720 with PFC3B
Supervisor Engine 720 Common Features
•Integrated 720-Gbps Switch Fabric
•64-MB bootflash device
•2 CompactFlash Type II slots (disk0 and disk1)
Note Some Supervisor Engine 720 Release 12.2SR images are larger than the bootflash device and must be stored on a CompactFlash card.
•Two Ethernet uplink ports:
–1-MB packet buffer per port
–Port 1—Gigabit Ethernet SFP
–Port 2—Configurable as Gigabit Ethernet SFP or 10/100/1000 Mbps RJ-45
•QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t
•Port grouping:
–Number of ports: 2
–Number of port groups: 1
–Port ranges per port group: 1-2
•Supervisor Engine 720 requires a high-capacity fan tray (see the "Fan Trays" section)
Supervisor Engine 720 with PFC3BXL
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-SUP720-3BXL
|
7.82 A@42 V
|
Supervisor Engine 720 with PFC3BXL:
•1-GB DRAM
•Policy Feature Card 3BXL (PFC3BXL); see the "RSP720-3C-10GE" section
•Multilayer Switch Feature Card 3 (MSFC3):
–1-GB DRAM
–64-MB bootflash
|
12.2(33)SRA
|
| |
Note There are no memory upgrade options for WS-SUP720-3BXL.
|
Supervisor Engine 720 with PFC3B
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-SUP720-3B
|
7.50 A@42 V
|
Supervisor Engine 720 with PFC3B:
•512-MB DRAM
•Policy Feature Card 3B (PFC3B); see the "RSP720-3C-10GE" section
•Multilayer Switch Feature Card 3 (MSFC3):
–512-MB DRAM
–64-MB bootflash
|
12.2(33)SRA
|
| |
Note
•There are no memory-only upgrade options for WS-SUP720-3B.
•Use WS-F6K-PFC3BXL= to upgrade a WS-SUP720-3B with a PFC3BXL. WS-F6K-PFC3BXL= includes 1 GB memory upgrades for the Supervisor Engine 720 and the MSFC3. Refer to this publication for more information:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_16220.htm
|
Supervisor Engine 32
Note Supervisor Engine 32 does not support this hardware:
•WS-SUP720-3B
•WS-F6K-PFC3BXL—Policy Feature Card 3BXL (PFC3BXL)
•Distributed Forwarding Cards (DFCs) (installed DFCs do not power up with a Supervisor Engine 32)
•Switch Fabric Modules
•These switching modules:
–WS-X6704-10GE—4-port 10-Gigabit Ethernet XENPAK
–WS-X6748-SFP—48-port Gigabit Ethernet SFP
–WS-X6724-SFP—24-port Gigabit Ethernet SFP
–WS-X6816-GBIC—16-port Gigabit Ethernet GBIC
–WS-X6748-GE-TX—48-port 10/100/1000 RJ-45
•7600-SIP-600—SPA Interface Processor-600
•Optical Services Modules (OSMs)
•CISCO7603—3-slot chassis
•These service modules:
–WS-SVC-AON-1-K9—Application-Oriented Networking Module
–WS-SVC-AGM-1-K9—Anomaly Guard Module
–WS-SVC-ADM-1-K9—Traffic Anomaly Detector Module
–WS-SVC-MWAM-1—Multi-Processor WAN Application Module
•Supervisor Engine 32 does not support these software features and commands:
–Protocol independent multicast (PIM) snooping designated-router flooding configurability
–NetFlow version 9
–Egress multicast replication
–Multicast replication mode detection
–All fabric configuration commands
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-SUP32-10GE-3B
|
2.39 A@42 V
|
Supervisor Engine 32:
•One 10/100/1000 Mbps RJ-45 port
•WS-SUP32-10GE—two Gigabit Ethernet ports (requires XENPAKs)
•WS-SUP32-GE—eight Gigabit Ethernet SFP ports (requires Gigabit Ethernet SFPs)
•512-MB DRAM
•256-MB bootflash
•Policy Feature Card 3B (PFC3B); see the "RSP720-3C-10GE" section
•Multilayer Switch Feature Card 2A (MSFC2A):
–512-MB DRAM
–64-MB bootflash
|
12.2(33)SRA
|
WS-SUP32-GE-3B
|
1.89 A@42 V
|
| |
Note See this publication for Supervisor Engine 32 hardware information:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/6000hw/supe_gd/index.htm
|
Route Switching Processor 720
RSP 720 Common Features
•Two Gigabit Ethernet uplink ports: port 1 supports a 1-Gbps small form pluggable (SFP) module; port 2 is configurable with either a 1-Gbps SFP module or a 10/100/1000-Mbps RJ-45
•Integrated 720-Gbps switch fabric
•Two CompactFlash Type II slots (on front panel) and 2-GB internal CompactFlash (1 GB each for RP and SP)
•Requires larger power supplies and a high-speed fan tray
•QoS port architecture (Rx/Tx) is 1p1q4t/1p2q2t
RSP720-3C-GE
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
RSP720-3C-GE
|
6.66 A@42 V
|
Route Switch Processor 720 with PFC3C:
•Two Gigabit Ethernet uplink ports: port 1 supports a 1-Gbps small form pluggable (SFP) module; port 2 is configurable with either a 1-Gbps SFP module or a 10/100/1000-Mbps RJ-45
•Integrated 720-Gbps switch fabric
•PFC3C and MSFC4 with 512-MB bootflash, 4-MB NVRAM, 4-MB ROMMON, and several DRAM options:
–Route processor (RP): 1- to 4-GB DRAM (default 1 GB)
–Switch processor (SP): 1- to 2-GB DRAM (default 1 GB)
•2 CompactFlash Type II slots (on front panel) and 2-GB internal CompactFlash (1 GB each for RP and SP)
•Requires larger power supplies and a high-speed fan tray
•QoS port architecture (Rx/Tx) is 1p1q4t/1p2q2t
|
12.2(33)SRB
|
| |
Note
•There are no memory-only upgrade options for RSP720-3C-GE.
•The following hardware and features are not supported by the RSP720-3C-GE:
–CISCO7603 router, OSR-7609 router.
–Optical Service Modules (OSMs), FlexWAN module (Enhanced FlexWAN module is supported).
–In-service software upgrade (ISSU) is not supported in Cisco IOS Release 12.2SRB.
–Server load balancing (SLB) is not supported.
•The RSP720-3C-GE supports the IPSEC-SPA-2G beginning with Cisco IOS Release 12.2(33)SRC.
|
RSP720-3CXL-GE
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
RSP720-3CXL-GE
|
7.33 A@42 V
|
Route Switch Processor 720 with PFC3CXL:
•Two Gigabit Ethernet uplink ports: port 1 supports a 1-Gbps small form pluggable (SFP) module; port 2 is configurable with either a 1-Gbps SFP module or a 10/100/1000-Mbps RJ-45
•Integrated 720-Gbps switch fabric
•PFC3CXL (high-capacity) and MSFC4 with 512-MB bootflash, 4-MB NVRAM, 4-MB ROMMON, and several DRAM options:
–Route processor (RP): 1- to 4-GB DRAM (default 2 GB)
–Switch processor (SP): 1- to 2-GB DRAM (default 1 GB)
•2 CompactFlash Type II slots (on front panel) and 2-GB internal CompactFlash (1 GB each for RP and SP)
•Requires larger power supplies and a high-speed fan tray
•QoS port architecture (Rx/Tx) is 1p1q4t/1p2q2t
|
12.2(33)SRB
|
| |
Note
•There are no memory-only upgrade options for RSP720-3CXL-GE.
•The RSP720-3CXL SP has one miniDIMM socket that accepts any vendor's 2GB DIMM. However, the RSP720-3CXL RP has two miniDIMM sockets. You must use the DIMMs from the same vendor for these sockets.
•The following hardware and features are not supported by the RSP720-3CXL-GE :
–Unsupported chassis: CISCO7603, OSR-7609.
–Unsupported modules: Optical Service Modules (OSMs), FlexWAN module (Enhanced FlexWAN module is supported).
–In-service software upgrade (ISSU) is not supported in Cisco IOS Release 12.2SRB.
–Server load balancing (SLB) is not supported.
•The RSP720-3CXL-GE supports the IPSEC-SPA-2G beginning with Cisco IOS Release 12.2(33)SRC.
|
RSP720-3C-10GE
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
RSP720-3C-10GE
|
7.33 A@42 V
|
Route Switch Processor 720 with uplink ports:
•Two 10 Gigabit Ethernet (10-GE) uplink ports support 10-Gbps X2 modules
•Three Gigabit Ethernet (1-GE) uplink ports: two ports support 1-Gbps small form-factor pluggable (SFP) module; one port supports 10/100/1000-Mbps RJ-45 connector
•Integrated 720-Gbps switch fabric
•PFC3C and MSFC4 with 512-MB bootflash, 4-MB NVRAM, 4-MB ROMmon, and several DRAM options:
–Route processor (RP): 1- to 2-GB DRAM (default 1 GB)
–Switch processor (SP): 1- to 2-GB DRAM (default 1 GB)
•One CompactFlash Type II slot (on front panel) and one 2-GB internal CompactFlash (1 GB each for RP and SP)
•Requires larger power supplies and a high-speed fan tray
•QoS port architecture, 10-GE ports (Rx/Tx): 8q8t/1p7q8t (CoS)
•QoS port architecture, 1-GE ports (Rx/Tx): 2q8t/1p3q8t
|
12.2(33)SRC
|
| |
Note
•There are no memory-only upgrade options for the RSP720-3C-10GE.
•The RSP720-3C-10GE does not support the following chassis and modules:
–Unsupported chassis: Cisco 7603, 7606, and 7613 chassis
–Unsupported modules: Services modules (excluding the Network Analysis Module) , Optical Service Modules (OSMs), FlexWAN module.
•The RSP720-3C-10GE supports the following 10-Gigabit Ethernet optics: X2-10GB-LR, X2-10GB-ER, X2-10GB-SR, X2-10GB-CX4, and X2-10GB-LX4.
•The RSP720-3C-10GE supports the following Gigabit Ethernet optics: GLC-SX-MM, GLC-LH-SM, GLC-ZX-SM, GLC-T, SFP-GE-S, SFP-GE-L, SFP-GE-T, GLC-BX-D, and GLC-BX-U.
In Cisco IOS Release 12.2SRC, the RSP720-10GE does not support the following features, which are supported on the RSP720:
•High-availability features such as NonStop Forwarding with Stateful Switchover (NSF/SSO) and In-Service Software Upgrade (ISSU) are not supported. Only Route Processor Redundancy (RPR) mode is supported.
•The uplinks on the standby RSP720-10GE are not active. This restriction exists because the uplink ports must perform lookups on the active RSP, which is not possible in RPR mode.
•Broadband aggregation features are not supported.
•The RSP720-10GE is on limited orderability. General orderability is expected with the 12.2(33)SRE release.
|
RSP720-3CXL-10GE
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
RSP720-3CXL-10GE
|
7.33 A@42 V
|
Route Switch Processor 720 with PFC3CXL:
•Two 10 Gigabit Ethernet (10-GE) uplink ports support 10-Gbps X2 modules
•Three Gigabit Ethernet (1-GE) uplink ports: two ports support 1-Gbps small form-factor pluggable (SFP) module; one port supports 10/100/1000-Mbps RJ-45 connector
•Integrated 720-Gbps switch fabric
•PFC3CXL (high-capacity) and MSFC4 with 512-MB bootflash, 4-MB NVRAM, 4-MB ROMmon, and several DRAM options:
–Route processor (RP): 1- to 2-GB DRAM (default 2 GB)
–Switch processor (SP): 1- to 2-GB DRAM (default 1 GB)
•One CompactFlash Type II slot (on front panel) and one 2-GB internal CompactFlash (1 GB each for RP and SP)
•Requires larger power supplies and a high-speed fan tray
•QoS port architecture, 10-GE ports (Rx/Tx): 8q8t/1p7q8t (CoS)
•QoS port architecture, 1-GE ports (Rx/Tx): 2q8t/1p3q8t
|
12.2(33)SRC
|
| |
Note
•There are no memory-only upgrade options for the RSP720-3CXL-10GE.
•The RSP720-3CXL-10GE does not support the following chassis and modules:
–Unsupported chassis: Cisco 7603, 7606, and 7613 chassis
–Unsupported modules: Services modules (excluding the Network Analysis Module) , Optical Service Modules (OSMs), FlexWAN module.
•The RSP720-3CXL-10GE supports the following 10-Gigabit Ethernet optics: X2-10GB-LR, X2-10GB-ER, X2-10GB-SR, X2-10GB-CX4, and X2-10GB-LX4.
•The RSP720-3CXL-10GE supports the following Gigabit Ethernet optics: GLC-SX-MM, GLC-LH-SM, GLC-ZX-SM, GLC-T, SFP-GE-S, SFP-GE-L, SSFP-GE-T, GLC-BX-D, and GLC-BX-U.
In Cisco IOS Release 12.2SRC, the RSP720-3CXL-10GE does not support the following features, which are supported on the RSP720:
•High-availability features such as NonStop Forwarding with Stateful Switchover (NSF/SSO) and In-Service Software Upgrade (ISSU) are not supported. Only Route Processor Redundancy (RPR) mode is supported.
•The uplinks on the standby RSP720-10GE are not active. This restriction exists because the uplink ports must perform lookups on the active RSP, which is not possible in RPR mode.
•Broadband aggregation features are not supported.
•The RSP720-10GE is on limited orderability. General orderability is expected with the 12.2(33)SRE release.
|
Policy Feature Cards
•Policy Feature Card Guidelines and Restrictions
•Policy Feature Card 3BXL
•Policy Feature Card 3B
•Distributed and Centralized Forwarding Cards
Policy Feature Card Guidelines and Restrictions
•The PFC3 supports a theoretical maximum of 64,000 MAC addresses (32,000 MAC addresses recommended maximum).
•You cannot use one type of PFC3 (PFC3BXL or PFC3B) on one supervisor engine and a different type on the other supervisor engine for redundancy. You must use identical policy feature cards for redundancy.
•Enter the show platform hardware pfc mode command to display the PFC3 mode.
•Enter the show platform earl-mode command to display the PFC3 mode.
•PFC3B—These restrictions apply to a configuration with a PFC3B and these DFCs:
–PFC3B and DFC3B—No restrictions.
–PFC3B and DFC3BXL—The PFC3B restricts DFC3BXL functionality: after a reload with a DFC3BXL-equipped module installed, the DFC3BXL functions as a DFC3B.
•PFC3BXL—These restrictions apply to a configuration with a PFC3BXL and these DFCs:
–PFC3BXL and DFC3B—PFC3BXL functionality is restricted by the DFC3B: after a reload with a DFC3B-equipped module installed (whether powered up or down), the PFC3BXL functions as a PFC3B.
–PFC3BXL and DFC3BXL—No restrictions.
•The features that require the PFC3BXL or PFC3B are not supported in PFC3A mode (see the Release Notes for Cisco IOS Release 12.2SR on the Cisco 7600 Series Routers).
•To use DFC3B-equipped switching modules with a PFC3BXL, the DFC3B-equipped switching modules must be installed at bootup.
Policy Feature Card 3BXL
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6K-PFC3BXL
|
2.57 A@42 V
|
Policy Feature Card 3BXL (PFC3BXL)
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note
•There are no memory upgrade options for WS-F6K-PFC3BXL.
•Use WS-F6K-PFC3BXL= to upgrade a WS-SUP720 or WS-SUP720-3B with a PFC3BXL. WS-F6K-PFC3BXL= includes 1 GB memory upgrades for the Supervisor Engine 720 and the MSFC3. Refer to this publication for more information:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_16220.htm
|
Policy Feature Card 3B
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6K-PFC3B
|
2.25 A@42 V
|
Policy Feature Card 3B (PFC3B)
|
With Supervisor Engine 720
|
12.2(33)SRA
|
With Supervisor Engine 32
|
12.2(33)SRA
|
Note
•There are no memory upgrade options for WS-F6K-PFC3B.
•Use WS-F6K-PFC3BXL= to upgrade a WS-SUP720-3B with a PFC3BXL. WS-F6K-PFC3BXL= includes 1 GB memory upgrades for the Supervisor Engine 720 and the MSFC3. Refer to this publication for more information:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_16220.htm
|
Policy Feature Card 3C
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6K-PFC3C
|
2.25 A@42 V
|
Policy Feature Card 3C (PFC3C)
|
| |
|
Supported only with RSP 720
|
12.2(33)SRB
|
Note
•There are no memory upgrade options for WS-F6K-PFC3C.
|
Policy Feature Card 3CXL
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6K-PFC3CXL
|
2.57 A@42 V
|
Policy Feature Card 3CXL (PFC3CXL)
|
| |
Supported only with RSP 720
|
12.2(33)SRB
|
Note
•There are no memory upgrade options for WS-F6K-PFC3BXL.
|
Distributed and Centralized Forwarding Cards
•Centralized Forwarding Card (WS-X6700-CFC)
•Distributed Forwarding Card 3BXL
•Distributed Forwarding Card 3B
•Distributed Forwarding Card 3CXL
•Distributed Forwarding Card 3C
Note See the "Route Switching Processor 720" section for Policy Feature Cards (PFC) and Distributed Forwarding Card (DFC) restrictions.
Centralized Forwarding Card (WS-X6700-CFC)
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-X6700-CFC
|
0.75 A@42 V
|
Centralized Forwarding Card (CFC) for use on CEF720 modules
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note There are no memory upgrade options for WS-X6700-CFC.
|
Distributed Forwarding Card 3BXL
•WS-F6700-DFC3BXL
•WS-F6K-DFC3BXL
WS-F6700-DFC3BXL
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6700-DFC3BXL
|
3.30 A@42 V
|
Distributed Forwarding Card 3BXL (DFC3BXL) for use on CEF720 modules
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note
•WS-F6700-DFC3BXL uses memory that is installed on the switching module.
•Refer to this publication for information about WS-F6700-DFC3BXL upgrades:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_15893.htm
|
WS-F6K-DFC3BXL
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6K-DFC3BXL
|
1.47 A@42 V
|
Distributed Forwarding Card 3BXL (DFC3BXL) for use on dCEF256 and CEF256 modules
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note
•Refer to this publication for information about WS-F6K-DFC3BXL memory upgrades:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_12409.htm
•Supervisor Engine 720 supports a WS-F6K-DFC3BXL on these WS-X6516-GBIC switching module hardware revisions:
–Lower than 5.0
–5.5 and higher
•Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 do not power up.
•With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 operate in bus mode.
•Refer to external field notice 24494 for more information about Supervisor Engine 720 and a DFC3 on WS-X6516-GBIC switching modules:
http://www.cisco.com/warp/public/770/fn24494.shtml
|
Distributed Forwarding Card 3B
•WS-F6700-DFC3B
•WS-F6K-DFC3B
WS-F6700-DFC3B
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6700-DFC3B
|
3.00 A@42 V
|
Distributed Forwarding Card 3B (DFC3B) for use on CEF720 modules
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note
•WS-F6700-DFC3B uses memory that is installed on the switching module.
•Refer to this publication for information about WS-F6700-DFC3B upgrades:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_15893.htm
|
WS-F6K-DFC3B
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6K-DFC3B
|
1.67 A@42 V
|
Distributed Forwarding Card 3B (DFC3B) for use on dCEF256 and CEF256 modules
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note
•Refer to this publication for information about WS-F6K-DFC3B memory upgrades:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_12409.htm
•Supervisor Engine 720 supports a WS-F6K-DFC3B on these WS-X6516-GBIC switching module hardware revisions:
–Lower than 5.0
–5.5 and higher
•Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 do not power up.
•With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 operate in bus mode.
•Refer to external field notice 24494 for more information about Supervisor Engine 720 and a DFC3 on WS-X6516-GBIC switching modules:
http://www.cisco.com/warp/public/770/fn24494.shtml
|
Distributed Forwarding Card 3CXL
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6700-DFC3CXL
|
2.35 A@42 V
|
Distributed Forwarding Card 3CXL (DFC3CXL) for use on CEF720 modules
|
| |
Supported with Supervisor Engine 720 and Route Switch Processor 720
|
12.2(33)SRB
|
Distributed Forwarding Card 3C
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-F6700-DFC3C
|
1.65 A@42 V
|
Distributed Forwarding Card 3C (DFC3C) for use on CEF720 modules
|
| |
Supported with Supervisor Engine 720 and Route Switch Processor 720
|
12.2(33)SRB
|
10-Gigabit Ethernet Switching Modules
Product ID
(append "=" for spares)
|
Power
Required
|
Product Description
|
Minimum Software Version
|
WS-X6704-10GE
|
6.28 A@42 V
|
4-port 10-Gigabit Ethernet XENPAK
•CEF720 with WS-X6700-CFC (adds 0.75 A@42 V)
•dCEF720 with WS-F6700-DFC3BXL (adds 3.30 A@42 V)
•dCEF720 with WS-F6700-DFC3B (adds 3.00 A@42 V)
•Supports egress multicast replication
•QoS port architecture (Rx/Tx):
–With DFC3: 8q8t/1p7q8t
–With CFC: 1q8t/1p7q8t
•Number of ports: 4
Number of port groups: 4
Port ranges per port group: 1 port in each group
|
| |
Supported only with Supervisor Engine 720
|
12.2(33)SRA
|
Note
•WS-X6704-10GE requires one of the following:
–WS-F6700-DFC3BXL (3.30 A@42 V)
–WS-F6700-DFC3B (3.00 A@42 V)
–WS-X6700-CFC (0.75 A@42 V)
•WS-X6704-10GE ships with WS-X6700-CFC installed unless ordered with WS-F6700-DFC3BXL or WS-F6700-DFC3B.
•WS-X6704-10GE is supported in the WS-C6503-E chassis.
•WS-X6704-10GE is not supported in the WS-C6503 and CISCO7603 chassis.
•In a |
