Table Of Contents
Cisco ICS 7750 FRU Installation and Replacement
Contents
Document Conventions
Required Tools and Equipment
PC Requirements
Safety Precautions and Maintenance Guidelines
General Safety Precautions
ESD Safety Precautions
Safety with Electricity
Telephone Wiring Guidelines
Lifting and Reaching Safety Precautions
System Component Identification
Removing and Replacing Cisco ICS 7750 Components
Hot Swapping Best Practices
Card Replacement Best Practices
Best Practices for Resetting or Removing Cards
Best Practices for Inspecting the Chassis Backplane and Card Connectors Before Installing Cards
Best Practices for Installing Cards
Removing and Replacing SPE 310s
Removing an SPE
Determining the Function of an SPE
Installing an SPE
Verifying SPE Installation
Configuring a New or Replacement SPE
SPE Installation and Replacement Scenarios
Installing a New SPE for Applications
Replacing an Existing SPE for Applications
Replacing the SPE Running System Manager
Removing and Replacing ASIs, MRPs, the SSP, or the SAP
Removing an ASI, MRP, SSP, or SAP
Stopping and Restarting the FMMServer (SSP Replacement Only)
Installing an ASI, MRP, SSP, or SAP
Installing or Replacing ASIs or MRPs
Replacing the SSP
Replacing the SAP
Removing and Replacing Interface Cards in ASI 81s or MRPs
Before You Begin
Installing or Replacing an Interface Card in an ASI 81 or MRP
Removing and Replacing Power Supply Modules
Removing Power Supply Modules
Installing Power Supply Modules
Removing and Replacing the Fan Tray
Removing the Fan Tray
Installing a Fan Tray
Verifying Card Installation
RMA Return Instructions
Checking the Status of Returned RMA Parts
Obtaining Documentation
World Wide Web
Documentation CD-ROM
Ordering Documentation
Documentation Feedback
Obtaining Technical Assistance
Cisco.com
Technical Assistance Center
Cisco TAC Web Site
Cisco TAC Escalation Center
Cisco ICS 7750 FRU Installation and Replacement
April 2, 2002
This document explains how to install and remove field-replaceable units (FRUs) in the Cisco Integrated Communications System 7750 (ICS 7750).
The following Cisco ICS 7750 components are FRUs:
•
Analog station interface (ASI) cards
•Fan tray
•Multiservice route processor (MRP) cards
•Power supply modules
•System alarm processor (SAP) card
•System processing engine (SPE) 310 cards
•System switch processor (SSP) card
•Voice interface cards (VICs), voice WAN interface cards (VWICs), and WAN interface cards (WICs). VICs, VWICs, and WICs are subcomponents of ASIs and MRPs.
Note This document is not intended for use with SPE 200s. If you need assistance with an SPE 200, contact the Cisco Technical Assistance Center (see the "Technical Assistance Center" section).
Note For information about removing and replacing dual in-line memory modules (DIMMs), packet voice data modules (PVDMs), and Virtual Private Networking (VPN) modules, refer to Installing Memory, PVDM, and VPN Modules in ASI Cards, MRP Cards, and SPE Cards in the Cisco ICS 7750. For additional information about system hardware, refer to the
Cisco ICS 7750 System Description.
Contents
This document contains the following sections:
•Document Conventions
•Required Tools and Equipment
•Safety Precautions and Maintenance Guidelines
•System Component Identification
•Removing and Replacing Cisco ICS 7750 Components
•Removing and Replacing SPE 310s
•Removing and Replacing ASIs, MRPs, the SSP, or the SAP
•Removing and Replacing Interface Cards in ASI 81s or MRPs
•Removing and Replacing Power Supply Modules
•Removing and Replacing the Fan Tray
•Verifying Card Installation
•RMA Return Instructions
•Obtaining Documentation
•Obtaining Technical Assistance
Document Conventions
This publication uses the following conventions:
Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual.
Caution Means
reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.
|
Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.
|
Waarschuwing
|
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information (Informatie over naleving van veiligheids- en andere voorschriften) raadplegen dat bij dit toestel is ingesloten.
|
Varoitus
|
Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä julkaisussa esiintyvien varoitusten käännökset löydät laitteen mukana olevasta Regulatory Compliance and Safety Information -kirjasesta (määräysten noudattaminen ja tietoa turvallisuudesta).
|
Attention
|
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers posés par les circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions d'avertissements figurant dans cette publication, consultez le document Regulatory Compliance and Safety Information (Conformité aux règlements et consignes de sécurité) qui accompagne cet appareil.
|
Warnung
|
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unfällen bewußt. Übersetzungen der in dieser Veröffentlichung enthaltenen Warnhinweise finden Sie im Dokument Regulatory Compliance and Safety Information (Informationen zu behördlichen Vorschriften und Sicherheit), das zusammen mit diesem Gerät geliefert wurde.
|
Avvertenza
|
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti. La traduzione delle avvertenze riportate in questa pubblicazione si trova nel documento Regulatory Compliance and Safety Information (Conformità alle norme e informazioni sulla sicurezza) che accompagna questo dispositivo.
|
Advarsel
|
Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til personskade. Før du utfører arbeid på utstyr, må du vare oppmerksom på de faremomentene som elektriske kretser innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker. Hvis du vil se oversettelser av de advarslene som finnes i denne publikasjonen, kan du se i dokumentet Regulatory Compliance and Safety Information (Overholdelse av forskrifter og sikkerhetsinformasjon) som ble levert med denne enheten.
|
Aviso
|
Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos físicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes. Para ver as traduções dos avisos que constam desta publicação, consulte o documento Regulatory Compliance and Safety Information (Informação de Segurança e Disposições Reguladoras) que acompanha este dispositivo.
|
¡Advertencia!
|
Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes. Para ver una traducción de las advertencias que aparecen en esta publicación, consultar el documento titulado Regulatory Compliance and Safety Information (Información sobre seguridad y conformidad con las disposiciones reglamentarias) que se acompaña con este dispositivo.
|
Varning!
|
Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador. Se förklaringar av de varningar som förkommer i denna publikation i dokumentet Regulatory Compliance and Safety Information (Efterrättelse av föreskrifter och säkerhetsinformation), vilket medföljer denna anordning.
|
Required Tools and Equipment
You need the following tools and parts to install and maintain the system. If you need additional equipment, contact a customer service representative for ordering information.
•A number-1 Phillips screwdriver for installing the cable management bracket (recommended) and mounting the system.
•A 6-mm open-end wrench for adjusting the grounding lug.
•ESD-prevention equipment or the disposable ESD-preventive wrist strap included in the hardware accessory kit.
•Antistatic mat, foam pad, or bag for removed cards or modules. (Put removed components inside an antistatic bag if you plan to return them to the factory; if you are replacing components, place them on an antistatic mat or foam pad.)
To remove, install, and replace SPEs, you need the following additional tools and parts:
•Cisco ICS 7750 chassis equipped with one or more SPE 310s.
•One or more spare SPE 310s.
•Windows-based PC or laptop, connected both to the SSP Ethernet port and the (SAP console port. (Specific requirements for this PC are described in the "PC Requirements" section.)
•Software:
–Cisco ICS 7750 System Software CD. The specific CD needed will vary, depending on the System Software version to be installed. See Table 1 for a list of the different software versions.
Note The System Software CD is needed only if you are replacing the SPE running System Manager.
–(Optional) Application CDs for applications to be installed on the SPE(s) (for example, Cisco CallManager Software for the Cisco ICS 7750).
•Cables and adapters:
–1 straight-through Category 5 Ethernet cable.
–1 RJ-45-to-DB-9 adapter.
–1 console (rolled EIA/TIA-232) cable.
PC Requirements
You need a PC (or laptop computer) to complete initial system configuration, to upload and install software bundles, and to perform system management tasks. The PC also needs to be physically near the ICS 7750 chassis, to allow for console (serial) and direct Ethernet connections.
Ensure that the PC meets the following requirements:
•CPU: Pentium-class 233 MHz or faster
•Memory: At least 64 MB of RAM
•Hardware:
–CD-ROM drive
–Network interface card (NIC)
–Available COM port
–PC keyboard with PS/2-style or USB (Universal Serial Bus) connector
–Windows-compatible mouse with PS/2-style or USB or connector
•Monitor: SVGA monitor or LCD display with at least 800 x 600 resolution and at least 256 colors (1024 x 768 resolution is recommended)
•Operating system: Microsoft Windows 98, Windows Me, Windows NT, or Windows 2000
•Web browser: Netscape Communicator 4.7 or later, or Internet Explorer 5.01 or later
•Communication software: Microsoft Terminal Services Client
Note Refer to the Cisco ICS 7750 Getting Started Guide for information about initial hardware installation and software configuration steps.
Safety Precautions and Maintenance Guidelines
This section describes guidelines that you should follow when working on the Cisco ICS 7750.
General Safety Precautions
Read the warnings in this section before working on the system.
Warning Read the installation instructions before you connect the system to its power source.
Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.
Warning This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 16A international) is used on the phase conductors (all current-carrying conductors).
Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use.
Warning Only personnel who are trained and qualified (IP Telephony certified for the Cisco ICS 7750) should be allowed to install or replace this equipment.
Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.
Warning The device is designed to work with TN power systems.
Warning The SPE contains a lithium battery. There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
ESD Safety Precautions
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD occurs when electronic printed circuit cards are improperly handled. ESD can result in complete or intermittent failures. Always follow these ESD-prevention procedures when removing and replacing cards and other system components:
•Ensure that the chassis is electrically connected to earth ground.
•Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact.
•Connect the clip to an unpainted surface of the chassis frame to safely channel unwanted ESD voltages to ground.
•To properly guard against ESD damage and shocks, the wrist strap must be used correctly. If no wrist strap is available, ground yourself by touching the metal part of the chassis.
Caution For safety, periodically check the resistance value of the antistatic strap, which should be between 1 and 10 megohms (Mohms).
Caution Static voltages as low as 30 volts can cause latent damage to circuitry. Be sure to observe all standard antistatic procedures (for example, wear a grounding strap) when handling electronic equipment and components.
Warning Blank faceplates (filler panels) serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards and faceplates are in place.
Safety with Electricity
Follow these guidelines when working on equipment powered by electricity:
•Locate the emergency power-off switch in the room in which you are working. Then, if an electrical accident occurs, you can quickly shut the power off.
•Disconnect all power before installing or removing a Cisco ICS 7750 chassis.
•Do not work alone if potentially hazardous conditions exist.
•Never assume that power is disconnected from a circuit. Always check.
•Look carefully for possible hazards in your work area, such as moist floors, ungrounded power extension cables, and missing safety grounds.
If an electrical accident occurs, proceed as follows:
•Use caution; do not become a victim yourself.
•Turn off power to the chassis.
•If possible, send another person to get medical aid. Otherwise, determine the condition of the victim, and then call for help.
•Determine whether the victim needs rescue breathing or external cardiac compressions; then take appropriate action.
Telephone Wiring Guidelines
Follow these guidelines when working with any equipment that is connected to telephone wiring or to other network cabling:
•Never install telephone wiring during a lightning storm.
•Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
•Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
•Use caution when installing or modifying telephone lines.
•Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
•Use caution when installing or modifying telephone lines.
Lifting and Reaching Safety Precautions
Follow these guidelines when lifting or moving the chassis:
Warning To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to support the weight of the unit. Lift the unit only by using handles that are an integral part of the chassis, or by grasping the chassis underneath its lower edge.
Warning Two people are required to lift the chassis. To prevent injury, keep your back straight and lift with your legs, not your back.
System Component Identification
Figure 1 shows the major components in a typical Cisco ICS 7750:
•Slots 1 through 6 can contain a combination of SPEs, ASIs, and MRPs.
•Slot 7 must contain only an SSP.
•Slot 8 must contain only an SAP.
•The Power Supply 1 and Power Supply 2 slots can each contain a power supply module (only one power supply module is required to operate the system).
•The system contains one fan tray, at the bottom of the chassis.
Note By factory-installed default, the Cisco ICS 7750chassis comes with the SPE running System Manager installed in slot 6, and with SPEs populated from right to left. Other system cards (such as MRPs and ASIs) are populated from left to right in the chassis.
Figure 1 Cisco ICS 7750
Removing and Replacing Cisco ICS 7750 Components
This section provides general information about removing and replacing the Cisco ICS 7750 components. This section contains the following subsections:
•Hot Swapping Best Practices
•Card Replacement Best Practices
For detailed instructions for removing and replacing system components, see the following sections:
•Removing and Replacing SPE 310s
•Removing and Replacing ASIs, MRPs, the SSP, or the SAP
•Removing and Replacing Power Supply Modules
•Removing and Replacing the Fan Tray
Warning When performing the procedures in this section, wear grounding wrist straps to avoid ESD damage to the Cisco ICS 7750. Do not directly touch the backplane with your hand or any metal tool to prevent personal injury or equipment damage.
Warning Removing cards, fans, and power supply modules can expose you to high-energy (high-amperage) circuits and possible ejection of molten metal or to the shock hazard of telephony circuit voltages. Be sure to remove all rings, watches, and other jewelry from fingers, wrists, and arms before removing panels and devices.
Note If the chassis has any empty slots, they are covered with blank panels when the Cisco ICS 7750 is shipped to you. Do not remove the panel covering an empty slot until you are ready to install a card in the slot.
Note You do not have to disassemble any system component or remove the chassis from the rack to perform any of the procedures described in this section.
Hot Swapping Best Practices
You can hot swap cards while the Cisco ICS 7750 is operating. With hot swapping, you do not need to power down the system. However, be sure to read and follow the best practices in this section, in the "Card Replacement Best Practices" section, and the specific instructions for removing and replacing each type of card or module before you hot swap it.
Warning Only trained and qualified (IP Telephony certified for the Cisco ICS 7750) personnel should be allowed to install or replace this equipment.
Caution When replacing a hot-swappable system card, you do not need to power down the entire chassis by using the chassis power supply switch or by unplugging the power supply. Powering down the entire chassis may cause the Cisco ICS 7750 to lose important configuration data and will interrupt any applications or functions running on other cards in the chassis. (The one exception to this is an electrical accident, in which case turning off the power is recommended; see the
"Safety with Electricity" section.)
Caution You can install only one SAP and one SSP in a single Cisco ICS 7750 chassis. If you must hot swap the SAP, the cooling fans do not operate; the system's ability to detect alarms associated with the operating environment, fans, and power supply modules is degraded; and applications using the COM ports on the SAP lose their access to those ports, until an operational SAP is properly reinserted in the chassis. If you must hot swap the SSP, the system loses LAN connectivity, and calls being made from or to Cisco IP phones that are switched through that SSP are disconnected until an operational SSP is properly reinserted in the chassis.
Note Depending on your system configuration, hot swapping of SPEs, ASIs, or MRPs can adversely affect users connected to the system. For example, if Cisco CallManager is running on only one SPE, hot swapping that SPE disconnects calls to or from the Public Switched Telephone Network (PSTN) and prevents the system from processing further PSTN traffic until an operational SPE is properly reinserted into the chassis. Similarly, hot swapping an ASI or MRP that is in the process of routing voice or WAN traffic prevents that traffic from reaching its destination. Contact your Cisco sales representative for guidelines on installing cards and software on your system for maximum availability and redundancy.
Card Replacement Best Practices
This section provides best practices for replacing system cards:
•Best Practices for Resetting or Removing Cards
•Best Practices for Inspecting the Chassis Backplane and Card Connectors Before Installing Cards
•Best Practices for Installing Cards
Best Practices for Resetting or Removing Cards
Consult these guidelines (and the instructions in "Hot Swapping Best Practices") before resetting or removing cards:
•Check card LEDs before attempting to reset or remove a card.
•Do not press the SHTDN button on any card in the Cisco ICS 7750 chassis unless you are directed to do so.
Caution Always use the extractor levers to disengage cards from the chassis. Failure to use the levers can cause system error messages that indicate a card failure. However, do not use the extractor levers to lift or support the weight of the cards.
Best Practices for Inspecting the Chassis Backplane and Card Connectors Before Installing Cards
Before you install a card, perform the following inspections:
•Inspect the backplane for bent pins or bent dividers between pin rows (see Figure 2).
If the backplane has bent pins, do not install a card in that slot. Installing a card into a damaged backplane slot will damage the connector on the card.
Figure 2 Backplane Inspection Check Points
•Inspect the card for damaged holes on the connector (see Figure 3).
If the connector has damaged holes, do not install the card. Installing a card that has a damaged connector will damage the backplane. Return damaged cards to Cisco (see the "RMA Return Instructions" section).
Figure 3 Card Connector Check Points
Best Practices for Installing Cards
When installing cards, consult these guidelines, and follow the card-specific instructions:
•Do not force the card faceplate into its slot. This action can damage the pins on the backplane if they are not aligned properly with the module or card.
•Before installing a card, be sure to align its top and bottom edges with the upper and lower card guides in the chassis slot. Do not attempt to push the card into its slot until its top and bottom edges are in proper alignment.
•When installing a card, carefully slide it all the way into the slot, and press both extractor levers inward (toward the center of the card) as far as they will go, as shown in Figure 5. The front of the card should now be flush with the other cards in the chassis. Using this method ensures that the card connector correctly mates with the backplane.
If the card is particularly tight in its slot, or if the extractor lever engagement hooks are not engaging with the chassis, you might need to back the card out and insert it again to cause its extractor levers to engage properly.
Caution Do not push the card with so much force that it bends in the middle, since bending a card might force its sensitive electronic components to come in contact with adjacent cards.
•The card or module should be firmly seated in the slot. Any card or module that is only partially connected to the backplane can disrupt system operation.
•After card installation is complete, always use the lock-down screws (at the top and bottom of the card) to secure the card firmly in place in the chassis. If the screws do not engage, the extractor levers are not properly aligned, and the card is not firmly seated in the chassis. Remove and reinsert the card until you can fully tighten the screws.
Removing and Replacing SPE 310s
This section describes how to install and replace SPEs and contains the following subsections:
•Removing an SPE
•Installing an SPE
•Verifying SPE Installation
•Configuring a New or Replacement SPE
Note This document is not intended for use with SPE 200s. If you need assistance with an SPE 200, contact the Cisco Technical Assistance Center (see the "Technical Assistance Center" section).
Removing an SPE
This section explains how to remove SPEs. Figure 4 shows how to remove a card.
Figure 4 Removing Cards from the Cisco ICS 7750 Chassis
You do not have to turn off the power for these procedures.
Caution When replacing an SPE, do not power down the entire chassis by using the chassis power supply switch or by unplugging the power supply. Powering down the entire chassis may cause the Cisco ICS 7750 to lose important configuration data and will interrupt any applications or functions running on other cards in the chassis.
Note Powering down an SPE will interrupt any services or applications running on that SPE. Measures should be taken to minimize impact on users.
Note If you have a chassis with more than one SPE installed and if you are not certain which SPE is running System Manager and which card or cards are running other applications, you can use ICS System Manager to check. See the "Determining the Function of an SPE" section.
Complete the following steps to remove an SPE:
Step 1 Press the SHTDN button on the card that you want to remove.
Note If the SPE to be removed is already shut down, this step is unnecessary, and you can proceed to Step 2.
The STATUS LED on the card starts blinking; after several minutes, it turns off. Wait for the STATUS LED to turn off before continuing.
Step 2 Put on an ESD-preventive wrist strap, and attach it to an unpainted chassis surface.
Caution To prevent ESD damage, handle cards by the edges only, and use an ESD-preventive wrist strap or other grounding device.
Step 3 For the SPE that you wish to remove, completely loosen the lock-down screws (at the top and bottom of the card).
Step 4 Press the upper and lower extractor levers outward (away from the center of the card) at the same time to disengage the card from the backplane. Pull the card out only far enough (about 1 inch) to disengage from the backplane; do not completely remove the card from the chassis.
Caution Always use the extractor levers to disengage or seat cards. Failure to use the levers can cause system error messages indicating a card failure. However, do not use the extractor levers to lift or support the weight of the cards.
Note Unseating or removal of the SPE should be done only when the SPE has been safely shut down. In normal use, you should not unseat or remove an SPE without first ensuring that the SPE has been shut down.
Warning High performance devices on system cards can get hot during operation. To remove a card, hold it by the faceplate and bottom edge. Allow the card to cool before touching any other part of it or placing it an anti-static bag.
Step 5 Grasp the extractor levers, and gently pull the card partially out of the chassis slot until you can grasp the card front panel with one hand. Place your other hand under the card to balance the weight of the card as you prepare to pull it out of the slot.
Step 6 Pull the card straight out of the slot. Avoid touching the circuitry or any connector pins.
Step 7 Place the card on an antistatic mat or foam pad until you are ready to reinstall it in the chassis. If you plan to return the card to the factory, place it inside an antistatic bag, and see the "RMA Return Instructions" section.
Step 8 Repeat Step 1 through Step 7 as needed to remove additional SPEs.
Determining the Function of an SPE
To use ICS System Manager to check the function of an SPE installed in the chassis, follow these steps:
Step 1 On the PC, launch a web browser, and access ICS System Manager by entering the following in the address field:
http://SPE IP address/ics
where SPE IP address is the IP address of the SPE running System Manager.
The ICS System Manager screen displays in the browser window, and you are prompted for a user ID and password.
Step 2 In the User ID field, enter admin.
Step 3 In the Password field, enter the ICS super admin password (set during ICSConfig).
Step 4 Click Login.
Step 5 Examine the displays provided in ICS System Manager to determine the function of each card in the chassis. For example:
ICS System Manager: V3.0.19
or
ICS Core Software: V3.0.19
Step 6 Exit ICS System Manager when you have finished.
Installing an SPE
This section explains how to install SPEs. Figure 5 shows how to install a card.
Figure 5 Installing Cards in the Cisco ICS 7750 Chassis
You do not need to turn off power for these procedures.
Caution When installing cards, be sure to apply equal amounts of pressure to the top and bottom of the card. You can damage the card and the chassis backplane if you apply too much pressure to either the top or the bottom of the card.
Follow these steps to install an SPE:
Step 1 Put on an ESD-preventive wrist strap, and attach it to an unpainted chassis surface.
Caution To prevent ESD damage, handle cards by the edges only, and use an ESD-preventive wrist strap or other grounding device.
Step 2 Align the SPE with the upper and lower card guides in an available chassis slot, and make sure that the extractor levers are in the open position (pointing up and down).
Step 3 With the top and bottom edges of the card in the card guides, gently slide the card into the chassis until you feel resistance. Because there are grounding clips near the front and rear of the card guides, you might need to increase the amount of force that you use to get the card past the grounding clips. If you encounter extreme resistance, pull the card out slightly and push it back in again.
Step 4 Press the upper and lower extractor levers inward (toward the center of the card) at the same time until they lock into their slots. This step firmly seats the SPE into the chassis.
Step 5 Fasten the lock-down screws for the SPE, securing it in the chassis.
Step 6 Verify the installation (see the "Verifying SPE Installation" section).
Verifying SPE Installation
This section explains how to verify an SPE installation.
To verify that the SPE is operating correctly, check that its STATUS LED is functioning as follows:
•The STATUS LED blinks green when the power-on self-test (POST) is in process or the card is shutting down.
•The STATUS LED is green when the POST is complete, card initialization is complete, and the card is operating correctly.
•The STATUS LED is off when the shutdown process is complete (indicates that the card can be removed from the chassis or that power is off for the entire Cisco ICS 7750).
Note The ALARM LED on Cisco ICS 7750 cards turns yellow during the POST. If the ALARM LED on any card does not turn off upon completion of the POST, that card is not functioning correctly. For general information on solving problems with cards, refer to Chapter 5, "Solving Hardware Problems," in the Cisco ICS 7750 Administration and Troubleshooting Guide.
Configuring a New or Replacement SPE
This section provides the procedures for configuring a new or replacement SPE after the SPE is installed. This section contains the following subsections:
•SPE Installation and Replacement Scenarios
•Installing a New SPE for Applications
•Replacing an Existing SPE for Applications
•Replacing the SPE Running System Manager
SPE Installation and Replacement Scenarios
This section describes the scenarios in which SPE installation and/or replacement might be required:
•Installing a new SPE for applications—In this instance, you already have a functioning SPE running System Manager in the Cisco ICS 7750 chassis, and you might have one or more existing SPEs for applications. The goal, as identified in this scenario, is to add another SPE and set it up so that it can have applications installed on it. (See the "Installing a New SPE for Applications" section.)
•Replacing an existing SPE for applications—In this case, you have an SPE for applications already installed in the chassis, but you wish to replace this SPE with a new one. Here, you might also want to migrate saved configuration data and settings to the new SPE once it is in place and operational. (This scenario includes the assumption that a successful backup was completed for the previously installed applications.) In this scenario, the existing SPE running System Manager and any other installed SPEs are left intact and unchanged. (See the "Replacing an Existing SPE for Applications" section.)
•Replacing the SPE running System Manager—This is a more complex scenario, and it requires the greatest number of steps to complete. In addition, although adding or replacing an SPE for applications can be done while the chassis is running, with minimal impact on users and services, replacing the SPE running System Manager takes more time and might require temporary interruption of services. For this reason, replacing the SPE running System Manager is best done at a time when interruption of service will have minimal impact, such as during scheduled maintenance. (See the "Replacing the SPE Running System Manager" section.)
Note Because there can be only one SPE running System Manager in a chassis, system software data must be backed up (if possible) before removing the original SPE running System Manager.
The following sections will address each of these scenarios. You need to follow only the instructions in the scenario that applies to your situation.
Note The procedures and steps for installing specific applications (such as Cisco CallManager) are beyond the scope of this document. For information on how to install, configure, back up, and restore Cisco ICS 7750-compatible applications, refer to the user documentation for those applications. If you still need assistance, see the "Obtaining Technical Assistance" section.
Note To reduce chances for error and other conditions which could result in lengthy interruption of Cisco ICS 7750 services, it is recommended that you attempt to install or replace only one SPE in a chassis at a time. If you need to perform this operation for more than one SPE in a chassis, complete the entire installation or replacement process for a single SPE, and verify that is functioning properly, before installing or replacing the next SPE.
Installing a New SPE for Applications
The procedures in this section apply to installing a new additional SPE in a Cisco ICS 7750 chassis; they do not apply to replacing an existing SPE for applications or to replacing the SPE running System Manager.
Note To replace an existing SPE for applications, see the "Replacing an Existing SPE for Applications" section. To replace the SPE running System Manager, see the "Replacing the SPE Running System Manager" section.
To install the new SPE for use as an additional SPE that runs applications, insert the SPE into an empty slot in the Cisco ICS 7750 chassis, following the instructions detailed in the "Installing an SPE" section.
Note If the slot for the replacement SPE is different from the original slot from which you removed the SPE, and if there was a COM port assigned for that SPE, you must reconfigure the COM ports (using ICS System Manager) to map the SPE to the new location. ICS System Manager does not automatically track this change. For information on how to reconfigure the COM port assignment, refer to the ICS System Manager online help.
Note After you install the SPE in the chassis, wait several minutes before you begin configuring the new SPE, so that the Windows 2000 operating system can finish booting. If you start ICSConfig before Windows 2000 is running, the new SPE will not be discovered, resulting in an error condition.
After you have installed the new SPE into the chassis, you can proceed to the "Using ICSConfig to Configure the New SPE for Applications" section.
If you wish to install applications on the SPE, see the "Installing Applications" section.
Using ICSConfig to Configure the New SPE for Applications
To configure the new SPE for applications, follow these steps:
Step 1 On the PC with network connectivity to the Cisco ICS 7750, launch a web browser.
Step 2 Enter the following URL:
http://SPE IP address/icsconfig/
where SPE IP address is the IP address of the SPE running System Manager.
Step 3 Log in as administrator, using the user ID administrator and the current password (the default is changeme).
Step 4 Click ICS 7700 System Setup.
Step 5 Make any necessary changes to the configuration screens. (Refer to the Cisco ICS 7750 Getting Started Guide for instructions.) Make a note of the IP address of the new SPE.
Step 6 When you have configured the necessary settings, the Summary page displays a list of all the configuration pages and the data entered in each field.
All of the page names listed on the Summary page are links to the configuration pages, where you can change any information that you entered. To change any of the settings, click the associated hyperlinked page. When the settings are correct, click Next to continue to the Ready to Submit page.
Note The Ready to Submit page provides instructions on what to do after you submit the changes to the Cisco ICS 7750. Submitting and processing these changes can require up to 20 minutes.
Step 7 Click Submit.
Caution After clicking
Submit, do not reboot your Cisco ICS 7750 or perform any configuration tasks on the Cisco ICS 7750 until this process has completed.
Step 8 Verify that the SPE is functioning correctly (see the "Verifying Card Installation" section).
After you have installed and configured the SPE, you can continue with the "Installing Applications" section.
Installing Applications
For information on how to install and configure applications on the newly installed SPE, refer to the documentation for the applications.
Replacing an Existing SPE for Applications
The procedures described in this section apply to replacing (or swapping) an existing SPE that is running applications only (not the SPE running System Manager). In this scenario, you remove an SPE for applications and replace it with a new SPE intended to perform the same functions as the previous SPE.
Note To install an additional SPE for applications, see the "Installing a New SPE for Applications" section. To replace the SPE running System Manager, see the "Replacing the SPE Running System Manager" section.
To replace an SPE for running applications that is already installed in an ICS 7750 chassis, you need to complete the following procedures:
•Back up configuration data and settings for the original SPE for applications (if application backup functions are available). See the "Backing Up Application Software Data" section.
•Shut down and remove the SPE that is to be replaced. See the "Shutting Down and Removing the SPE for Applications" section.
•Insert and power up the new SPE in the same or a different chassis slot. See the "Installing the Replacement SPE for Applications" section.
•Set the correct date, time, and host name for the SPE. See the "Setting the Date, Time, and Host Name on the Replacement SPE" section.
•Use ICSConfig to configure the SPE. See the "Using ICSConfig to Configure the Replacement SPE for Applications" section.
•Install applications and restore application configuration data and settings (if available). See the "Installing Applications" section.
The following sections describe the process in detail.
Backing Up Application Software Data
For information on how to back up application data on an existing SPE, refer to the documentation for each application. Note that not all applications have built-in backup and restore features; in those cases, you need to back up and restore the application data manually.
If you do plan to restore backed up application data, you should also record the IP address and host name of the SPE being replaced. Later, during the configuration phase of setting up the SPE for applications, you will be directed to rename the SPE to match the host name of the card you removed.
To locate the SPE host name, follow these steps:
Step 1 Connect a monitor cable to the monitor port on the SPE.
Step 2 Connect a "Y" cable for your keyboard and mouse to the PS/2 keyboard and mouse ports on the SPE.
Step 3 Log in as an administrator (user ID administrator), and enter your password (the default is changeme).
Step 4 On the SPE, use either the Command Prompt (DOS) window or the Windows System Properties dialog box to find the host name. To use the Command Prompt window, go to Step 5. To use the System Properties dialog box, go to Step 7.
Step 5 Choose Start > Programs > Accessories > Command Prompt.
Step 6 Enter the hostname command. The SPE host name appears. Record the host name and skip the rest of this procedure.
Step 7 Choose Start > Settings > Control Panel > System.
Step 8 In the System Properties dialog box, under the Network Identification tab, click Properties.
Step 9 In the Identification Changes dialog box, the Computer Name field displays the host name. Record this information.
Step 10 Click Cancel to close the Identification Changes dialog box, and close the System Properties dialog box.
After you have recorded the SPE host name and backed up the application software data, you can continue with the "Shutting Down and Removing the SPE for Applications" section.
Shutting Down and Removing the SPE for Applications
To shut down and remove the old SPE, follow the instructions detailed in the "Removing an SPE" section.
After you have removed the old SPE for running applications, you can continue with the "Installing the Replacement SPE for Applications" section.
Installing the Replacement SPE for Applications
To install the replacement SPE for applications, insert the SPE into the same chassis slot from which you removed the old SPE for applications. Follow the instructions in the "Installing an SPE" section.
After you have installed the SPE in the chassis, you can continue with the "Setting the Date, Time, and Host Name on the Replacement SPE" section.
Setting the Date, Time, and Host Name on the Replacement SPE
If you have backed up application software data that can be restored only to an SPE having the same host name, use the following procedure to change the host name. (This is the case, for instance, with Cisco CallManager backups.)
To set the correct date and time and to change the host name on the SPE, follow these steps:
Step 1 Connect the monitor cable to the monitor port on the SPE.
Step 2 Connect a "Y" cable for your keyboard and mouse to the PS/2 keyboard and mouse ports on the SPE.
Step 3 Log in as an administrator (user ID administrator), and enter your password (the default is changeme).
Step 4 Choose Start > Settings > Control Panel > Date/Time.
Step 5 In the Date/Time Properties window, set the correct date and time in the Date & Time tab, and set the appropriate time zone in the Time Zone tab. Click OK to accept the changes.
Step 6 If you have backed up application data that can be restored only to an SPE by using the same host name, proceed to the next step. If no host name change is required, skip the remaining steps, and continue with the "Using ICSConfig to Configure the Replacement SPE for Applications" section.
Step 7 In the Control Panel, double-click System to open System Properties.
Step 8 In the System Properties dialog box, under the Network Identification tab, click Properties.
Step 9 In the Identification Changes dialog box, in the Computer Name field, enter the host name (maximum of 15 characters) you originally had for the SPE you removed, and click OK.
Step 10 Click OK to close the System Properties dialog box.
Step 11 You are prompted to reboot the system. Click OK to reboot the SPE, implementing the host name change.
After you have completed the SPE host name change, continue with the "Using ICSConfig to Configure the Replacement SPE for Applications" section.
Using ICSConfig to Configure the Replacement SPE for Applications
To configure the SPE, using ICSConfig, complete the following steps:
Step 1 On the PC, launch a web browser.
Step 2 Enter the following URL:
http://SPE IP address/icsconfig/
where the address entered is the IP address of the SPE running System Manager.
Step 3 Log in as administrator (using the user ID administrator and the default password changeme).
Step 4 Click ICS 7700 System Setup.
Step 5 Make any necessary changes to the configuration screens, ensuring that the new SPE has the same IP address as the IP address of the SPE that was replaced. Refer to the Cisco ICS 7750 Getting Started Guide for instructions.
Step 6 When you have configured the necessary settings, the Summary page displays a list of all the configuration pages and the data entered in each field.
All the page names listed on the Summary page are links to the configuration pages, where you can change any information that you entered. To change any of the settings, click the associated hyperlinked page. When all the settings are correct, click Next to continue to the Ready to Submit page.
Note The Ready to Submit page provides instructions on what to do after you submit the changes to your Cisco ICS 7750. Submitting and processing these changes can take up to 20 minutes to complete.
Step 7 Click Submit.
Caution After clicking
Submit, do not reboot your Cisco ICS 7750 or perform any configuration tasks on the Cisco ICS 7750 during this process.
Step 8 Verify that the SPE is functioning correctly (see the "Verifying Card Installation" section).
After the SPE is installed and configured, you can proceed to the "Installing Applications and Restoring Saved Application Data" section.
Installing Applications and Restoring Saved Application Data
For information on how to install and configure applications on the newly installed SPE, refer to the documentation for the applications. Similarly, for details on how to restore saved or backed-up application data, where such functions are available, see the application documentation.
Replacing the SPE Running System Manager
In this scenario, you replace the SPE running System Manager with a new SPE.
Note The Cisco ICS 7750 supports the operation of only one SPE running System Manager in a chassis. For this reason, the process involves backing up system software data on the original SPE running System Manager before installing and restoring data to the new SPE.
Note The Cisco ICS 7750 services will be interrupted briefly during this process. It is therefore recommended that you replace the SPE running System Manager at a time when impact to users will be minimized, such as during scheduled maintenance or outside normal business hours.
Follow these steps to replace the SPE running System Manager:
Step 1 Back up system data on the original SPE running System Manager. See the "Backing Up System Software Data" section.
Step 2 If there are any applications installed on the SPE that support backup functionality, back up the application data and settings. See the "Backing Up Application Data" section.
Step 3 Shut down and remove the original SPE to be replaced. See the "Shutting Down and Removing the SPE Running System Manager" section.
Step 4 Insert the SPE into the same (now empty) chassis slot from which you removed the original SPE running System Manager. See the "Installing an SPE" section.
Step 5 Remove the factory-installed ICS Core Software. See the "Uninstalling the ICS Core Software" section.
Step 6 Set the date, time, and host name for the SPE. See the "Setting the Date, Time, and Host Name of the Replacement SPE" section.
Step 7 Prepare to install the ICS System Manager software. See the "Preparing for the Installation of the ICS System Software" section.
If you need to configure the IP address of the attached PC, see the "Configuring Your PC IP Address" section.
Step 8 Install the ICS System Software using the Image Install Tool. See the "Using the ICS Image Install Tool to Install the ICS System Software" section.
Step 9 Restore the backed up ICS System Manager data and settings. See the "Restoring System Software Data" section.
If no ICS System Manager data backup is available, see the "Running ICSConfig When System Backup Is Unavailable" section.
Step 10 Use ICSConfig to configure or verify the settings of the new ICS System Manager. See the "Using ICSConfig to Configure and Verify the SPE Running System Manager" section.
Step 11 Access ICS System Manager, and restore the functionality of the system. See the "Accessing ICS System Manager and Restoring Cisco ICS 7750 Functionality" section.
Step 12 (Optional) Install applications, and restore application configuration data and settings (if available). See the "Installing Applications and Restoring Saved Application Software Data" section.
The following sections describe the process in detail.
Backing Up System Software Data
Before replacing the SPE running System Manager, you should always create a backup of the system software configuration, if possible. This system backup will include SPE registry settings, ICS System Manager database records, and IOS configuration files for ASIs and MRPs.
If you do not have a valid backup, you will need to configure the new SPE running System Manager as if it is a new Cisco ICS 7750 chassis installation, a process which takes a considerably longer time to complete. See the Cisco ICS 7750 Getting Started Guide for information and procedures on how to do this.
For instructions on how to back up system software data, see the Release Notes for the Cisco ICS 7750 for System Software Release 2.x.x. Be sure to back up to a hard disk location other than on the SPE that you are removing, and make sure that there is enough disk space for the backup (approximately 75 MB).
Note COM port assignment information is not stored in the ICS System Manager database and is not included when you perform a backup in System Maintenance. You may need to reconfigure the COM port assignment after you restore the ICS System Manager data.
You should also record the host name for the SPE running System Manager that is being replaced. Later, during the configuration phase of setting up the new SPE, you will be directed to rename the SPE to match the host name of the card you removed.
To locate the SPE host name, follow these steps:
Step 1 Connect the monitor cable to the monitor port on the SPE.
Step 2 Connect a "Y" cable for your keyboard and mouse to the PS/2 keyboard and mouse ports on the SPE.
Step 3 Log in as an administrator (user ID administrator), and enter your password (the default is changeme).
Step 4 On the SPE, use either the Command Prompt (DOS) window or the Windows System Properties dialog box to find the host name. To use the Command Prompt window, go to Step 5. To use the System Properties dialog box, go to Step 7.
Step 5 To open the Command Prompt window, choose Start > Programs > Accessories > Command Prompt.
Step 6 Enter the hostname command. The SPE host name appears. Record the host name, and skip the rest of this procedure.
Step 7 To access the System Properties dialog box, choose Start > Settings > Control Panel > System.
Step 8 In the System Properties dialog box, under the Network Identification tab, click Properties.
Step 9 In the Identification Changes dialog box, the Computer Name field displays the host name. Record this information.
Step 10 Click Cancel to
