Table Of Contents
Cisco ICS 7750 FRU Installation and Replacement
Contents
Document Conventions
Required Tools and Equipment
PC Requirements
Safety Precautions and Maintenance Guidelines
General Safety Precautions
ESD Safety Precautions
Safety with Electricity
Ground Conductor Warning
Use Copper Conductors Only
Electrical Storm Warning
Telephone Jacks in Wet Locations Warning
Uninsulated Wires and Terminals Warning
Line Installation or Modification Warning
Telephone Use During an Electrical Storm Warning
Telephone Use by Gas Leaks Warning
Installation Hazard
Grounding Requirement Warning
More Than One Power Supply Warning
Telephone Wiring Guidelines
Lifting and Reaching Safety Precautions
System Component Identification
Removing and Replacing Cisco ICS 7750 Components
Best Practices for Hot Swapping
Best Practices for Card Replacement
Best Practices for Resetting or Removing Cards
Best Practices for Inspecting the Chassis Backplane and Card Connectors Before Installing Cards
Best Practices for Installing Cards
Removing and Replacing SPE310s
Accessing the SPE310
Accessing the SPE310 Windows Interface Through Terminal Services Client
Accessing the SPE310 Windows Interface Through Directly Connected Peripherals
Installing Microsoft Terminal Services Client
Determining the Function of an SPE
Removing an SPE
Installing an SPE
Verifying SPE Installation
Configuring a New or Replacement SPE
SPE Installation and Replacement Scenarios
Installing a New SPE for Applications
Replacing an Existing SPE for Applications
Replacing the SPE Running System Manager
Converting the ICS Core Software to ICS System Manager Software
Configuring Your PC IP Address
Configuring Your Web Browser for System Manager
Using ICSConfig to Configure and Verify the SPE Running System Manager
Accessing ICS System Manager and Restoring Cisco ICS 7750 Functionality
Installing Applications and Restoring Saved Application Software Data
Downgrading ICS System Software
Removing and Replacing ASIs, MRPs, the SSP, or the SAP
Backing Up and Restoring Flash-Based MRPs, ASIs, and the SSP
Removing an ASI, MRP, SSP, or SAP
Installing or Replacing an ASI or MRP
Replacing an MRP200 or ASI Card with a Flash-Based MRP Card
Removing and Replacing Interface Cards in ASI81s, MRP3-8FXSs, or MRPs
Electrical Storm Warning
Telephone Jacks in Wet Locations Warning
Uninsulated Wires and Terminals Warning
Line Installation or Modification Warning
Telephone Use During an Electrical Storm Warning
Telephone Use by Gas Leaks Warning
Installation Hazard
Before You Begin
Installing or Replacing an Interface Card in an ASI81, MRP, or MRP3-8FXS
Configuring VLAN Support on the Flash-Based MRP
Replacing the SSP and the SAP
Backing up and Restoring the VLAN Configuration on the SSP
Replacing the SSP
Configuring VLAN Support on the SSP
Replacing the SAP
Removing and Replacing Power Supply Modules
Removing Power Supply Modules
Installing Power Supply Modules
Removing and Replacing the Fan Tray
Removing the Fan Tray
Installing a Fan Tray
Verifying Card Installation
RMA Return Instructions
Checking the Status of Returned RMA Parts
Obtaining Documentation
World Wide Web
Documentation CD-ROM
Ordering Documentation
Documentation Feedback
Obtaining Technical Assistance
Cisco.com
Technical Assistance Center
Cisco TAC Web Site
Cisco TAC Escalation Center
Cisco ICS 7750 FRU Installation and Replacement
October 2, 2002
This document explains how to install and remove field-replaceable units (FRUs) in the Cisco Integrated Communications System (ICS) 7750 (referred to as the Cisco ICS 7750).
The following Cisco ICS 7750 components are FRUs:
•
Analog station interface (ASI) cards.
•Fan tray.
•Multiservice route processor (MRP) 200 and 300 cards.
•MRP3-8FXS and MRP3-16FXS cards.
•Power supply modules.
•System alarm processor (SAP) card.
•System processing engine (SPE) 310 cards.
•System switch processor (SSP) card.
•Voice interface cards (VICs), voice WAN interface cards (VWICs), and WAN interface cards (WICs). VICs, VWICs, and WICs are subcomponents of ASIs and MRPs.
Note This document is not intended for use with SPE200s. If you need assistance with an SPE200, contact the Cisco Technical Assistance Center (see the "Technical Assistance Center" section).
Note The MRP200 and MRP300 cards are both voice-and-data-capable routers that support digital and analog voice trunks and WAN routing interfaces to link remote Ethernet LANs to the Public Switched Telephone Network (PSTN), to existing private branch exchanges (PBXs), and to most common analog devices, such as fax machines and teleconferencing stations. The MRP300 has additional functionality provided by 16 MB of onboard Flash memory, with 64 MB of add-on Flash memory available as an option. Configuration files for the MRP200 are loaded and saved to the SPE running System Manager, whereas configuration files for the MRP300 are loaded and saved on the MRP300 in nonvolatile RAM (NVRAM).
Note The ASI81 and MRP3-8FXS cards are both voice-and-data-capable routers that can carry voice traffic over an IP network to link remote Ethernet LANs to central offices over WAN links (depending on the type of card installed in its WIC/VIC/VWIC slot). Each card can support eight connections to analog telephones, fax machines, and teleconferencing stations. The MRP3-8FXS has additional functionality provided by 16 MB of onboard Flash memory, with 64 MB of add-on Flash memory available as an option. Configuration files for the MRP3-8FXS are loaded and saved on the MRP3-8FXS in NVRAM. The MRP3-16FXS card has the same Flash memory capability, with support for 16 connections. (The ASI160 card also supports 16 connections, but does not have the capability for Flash memory.)
Caution Beginning with release 2.5.0, ICS System Software has been enhanced to include support for virtual local area networks (VLANs) and quality of service (QoS) on the Cisco ICS 7750. With this support, you can enable VLAN usage by configuring all system cards on the management VLAN (VLAN 1); you can also configure multiple data and voice VLANs outside of the Cisco ICS 7750 chassis. The implementation of VLANs and QoS includes the ability for the Flash-based MRP cards (MRP300, MRP3-8FXS, and MRP3-16FXS) to be configured as VLAN routers to route between multiple VLANs configured on the LAN. As VLAN routers, the Flash-based MRP cards can reside on other VLANs besides VLAN 1. Additional functionality provided by a DHCP server on the Flash-based MRP cards can be configured to provision IP addresses for external devices, such as PCs and phones, on VLANs other than VLAN 1.
To enable VLAN functionality on the Cisco ICS 7750, you need to manually configure both the VLAN-capable, Flash-based MRP card and the SSP through the IOS command-line interface (CLI). For detailed information about VLAN functionality on the Cisco ICS 7750, refer to the
Cisco ICS 7750 Installation and Configuration Guide. For information about configuring VLANs, refer to the "Configuring VLANs" section in the Catalyst 2900 XL and Catalyst 3500 XL Software Configuration Guide, Releases 12.0(5)WC4 and 12.0(5)WC5. For information about configuring a DHCP server on the Flash-based MRP card, refer to the "Configuring DHCP" section in the Cisco IOS IP Configuration Guide, Release 12.2.
Note For a description of the features, modifications, and caveats for the Cisco Integrated Communications System 7750 (Cisco ICS 7750) release 2.5.0, refer to the
Release Notes for System Software Release 2.5.0 on the Cisco ICS 7750.
Note For information about removing and replacing dual in-line memory modules (DIMMs), packet voice data modules (PVDMs), and Virtual Private Networking (VPN) modules, refer to Installing Memory, PVDM, and VPN Modules in ASI Cards, MRP Cards, and SPE Cards in the Cisco ICS 7750. For additional information about system hardware, refer to the
Cisco ICS 7750 System Description and the Cisco ICS 7750 Installation and Configuration Guide.
Contents
This document contains the following sections:
•Document Conventions
•Required Tools and Equipment
•Safety Precautions and Maintenance Guidelines
•System Component Identification
•Removing and Replacing Cisco ICS 7750 Components
•Removing and Replacing SPE310s
•Removing and Replacing ASIs, MRPs, the SSP, or the SAP
•Removing and Replacing Interface Cards in ASI81s, MRP3-8FXSs, or MRPs
•Removing and Replacing Power Supply Modules
•Removing and Replacing the Fan Tray
•Verifying Card Installation
•RMA Return Instructions
•Obtaining Documentation
•Obtaining Technical Assistance
Document Conventions
This publication uses the following conventions:
Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual.
Caution Means
reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.
|
Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.
|
Waarschuwing
|
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information (Informatie over naleving van veiligheids- en andere voorschriften) raadplegen dat bij dit toestel is ingesloten.
|
Varoitus
|
Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä julkaisussa esiintyvien varoitusten käännökset löydät laitteen mukana olevasta Regulatory Compliance and Safety Information -kirjasesta (määräysten noudattaminen ja tietoa turvallisuudesta).
|
Attention
|
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers posés par les circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions d'avertissements figurant dans cette publication, consultez le document Regulatory Compliance and Safety Information (Conformité aux règlements et consignes de sécurité) qui accompagne cet appareil.
|
Warnung
|
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unfällen bewußt. Übersetzungen der in dieser Veröffentlichung enthaltenen Warnhinweise finden Sie im Dokument Regulatory Compliance and Safety Information (Informationen zu behördlichen Vorschriften und Sicherheit), das zusammen mit diesem Gerät geliefert wurde.
|
Avvertenza
|
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti. La traduzione delle avvertenze riportate in questa pubblicazione si trova nel documento Regulatory Compliance and Safety Information (Conformità alle norme e informazioni sulla sicurezza) che accompagna questo dispositivo.
|
Advarsel
|
Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til personskade. Før du utfører arbeid på utstyr, må du vare oppmerksom på de faremomentene som elektriske kretser innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker. Hvis du vil se oversettelser av de advarslene som finnes i denne publikasjonen, kan du se i dokumentet Regulatory Compliance and Safety Information (Overholdelse av forskrifter og sikkerhetsinformasjon) som ble levert med denne enheten.
|
Aviso
|
Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos físicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes. Para ver as traduções dos avisos que constam desta publicação, consulte o documento Regulatory Compliance and Safety Information (Informação de Segurança e Disposições Reguladoras) que acompanha este dispositivo.
|
¡Advertencia!
|
Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes. Para ver una traducción de las advertencias que aparecen en esta publicación, consultar el documento titulado Regulatory Compliance and Safety Information (Información sobre seguridad y conformidad con las disposiciones reglamentarias) que se acompaña con este dispositivo.
|
Varning!
|
Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador. Se förklaringar av de varningar som förkommer i denna publikation i dokumentet Regulatory Compliance and Safety Information (Efterrättelse av föreskrifter och säkerhetsinformation), vilket medföljer denna anordning.
|
Required Tools and Equipment
Warning Only personnel who are trained and qualified (IP Telephony certified for the Cisco ICS 7750) should be allowed to install or replace this equipment.
You need the following tools and parts to install and maintain the system. If you need additional equipment, contact a customer service representative for ordering information.
•A number-1 Phillips screwdriver for installing the cable management bracket (recommended) and mounting the system.
•A 6-mm open-end wrench for adjusting the grounding lug.
•ESD-prevention equipment or the disposable ESD-preventive wrist strap included in the hardware accessory kit.
•Antistatic mat, foam pad, or bag for removed cards or modules. (Put removed components inside an antistatic bag if you plan to return them to the factory; if you are replacing components, place them on an antistatic mat or foam pad.)
•Cables and adapters:
–1 straight-through Category 5 Ethernet cable.
–1 RJ-45-to-DB-9 adapter.
–1 console (rolled EIA/TIA-232) cable.
To remove, install, and replace SPEs, you need the following additional tools and parts:
•Cisco ICS 7750 chassis equipped with one or more SPE310s.
•One or more spare SPE310s.
•(Optional) Application CDs for applications to be installed on the SPE(s) (for example, Cisco CallManager software for the Cisco ICS 7750).
•Windows-based PC or laptop, which may be connected both to the SSP Ethernet port and the SAP console port. (Specific requirements for this PC are described in the "PC Requirements" section.)
•Cisco ICS 7750 System Software, which can be installed from the following sources, with the following options:
–CD-ROM—The system software release 2.x.x CD-ROM contains a complete set of the system software, including Microsoft SQL Server software and Microsoft hotfixes. The CD-ROM can be used to install release 2.x.x on an SPE310 that does not currently have system software installed, or it can be used to upgrade an SPE310 that currently has system software release 2.1.0 or higher installed.
For instructions on installing the software from the CD-ROM, refer to the "Upgrading System Software on SPE310s from the CD-ROM" section in Chapter 8, "Maintaining the Cisco ICS 7750," in the Cisco ICS 7750 Installation and Configuration Guide. For download and installation instructions from CCO, refer to the "Downloading and Installing System Software" section in Chapter 8, "Maintaining the Cisco ICS 7750," in the Cisco ICS 7750 Installation and Configuration Guide.
–CCO—Two sets of system software release 2.x.x are available for downloading from CCO:
•S77a-2.x.x.exe—This package contains the complete set of system software version 2.x.x, including Microsoft SQL Server software. You can use this package for new installations or upgrades of existing system software.
•S77a-Upgrade-2.x.x.exe—This package contains only the software components changed since release 2.1.0 and necessary to upgrade the ICS System Software from release 2.1.0 or later. Because it does not contain Microsoft SQL Server software, the package is smaller and requires less download time. You cannot use this upgrade package for SPE310 reimaging or reinstallation of ICS System Software.
You can install ICS System Manager Software on only one SPE310 in the chassis. On any additional SPE310s in the chassis, install ICS Core Software. Refer to the Cisco ICS 7750 Installation and Configuration Guide for information about the applicable system software installation options.
The Cisco ICS 7750 system software packages use the naming conventions shown in Table 1.
Table 1 Cisco ICS 7750 System Software Packages
System Software Package Name 1
|
Feature Set
|
IOS Software Image (for MRPs and ASIs)
|
S77a-x.x.x.exe
|
SNMP2 , IP, Bridging, SRB3 , Voice, Reduced IP (SNMP, IP RIP4 /IGRP5 /EIGRP6 , Bridging, ISDN, PPP)
|
ics7700-sv3y-mz
|
S77a-Upgrade-x.x.x.exe
|
SNMP, IP, Bridging, SRB, Voice, Reduced IP (SNMP, IP RIP/IGRP/EIGRP, Bridging, ISDN, PPP)
|
ics7700-sv3y-mz
|
Note Beginning with ICS System Software release 2.4.0, the Cisco ICS 7750 System Software installation CD contents and upgrade-only packages have been available on CCO in a compressed format. The files distributed on CCO are packaged as a single self-extracting EXE. Refer to the Cisco Voice Software download page at http://www.cisco.com/public/sw-center/sw-voice.shtml for the CCO version. You will have to download the EXE file to your SPE310 and then invoke the executable by double-clicking the file. This expands the package files and automatically creates the directory structure required for installation. For installation instructions, refer to the "Upgrading System Software" section in Chapter 8, "Maintaining the Cisco ICS 7750," in the Cisco ICS 7750 Installation and Configuration Guide.
Note The full ICS System Software package (CD or CCO version) is needed if you are replacing the SPE running System Manager.
PC Requirements
You may choose to use a PC (or laptop computer) to download and install software and to perform system management tasks, such as remote configuration or troubleshooting. The PC does not need to be physically near the ICS 7750 chassis because tasks can be executed locally on the SPE310 with an attached keyboard, mouse, and monitor.
Ensure that the PC meets the following requirements:
•CPU: Pentium-class 233 MHz or faster
•Memory: At least 64 MB of RAM
•Hardware:
–CD-ROM drive
–Network interface card (NIC)
–Available COM port
–PC keyboard with PS/2-style or USB (Universal Serial Bus) connector
–Windows-compatible mouse with PS/2-style or USB or connector
•Monitor: SVGA monitor or LCD display with at least 800 x 600 resolution and at least 256 colors (1024 x 768 resolution is recommended)
•Operating system: Microsoft Windows 98, Windows Me, Windows XP, Windows NT, or Windows 2000
•Web browser: Netscape Communicator 4.7 or later, or Internet Explorer 5.5 or later, with Java plug-in version 1.3.1 or later (refer to the Cisco Software Download web site at http://www.cisco.com/pcgi-bin/tablebuild.pl/java).
•Communication software: Microsoft Terminal Services Client
Note Refer to the Cisco ICS 7750 Installation and Configuration Guide for information about initial hardware installation and software configuration steps.
Safety Precautions and Maintenance Guidelines
Note The following guidelines are IMPORTANT SAFETY INSTRUCTIONS.
This section describes guidelines that you should follow when working on the Cisco ICS 7750.
General Safety Precautions
Read the warnings in this section before working on the system.
Warning Read the installation instructions before you connect the system to its power source.
Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.
Warning This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 16A international) is used on the phase conductors (all current-carrying conductors).
Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use.
Warning Only personnel who are trained and qualified (IP Telephony certified for the Cisco ICS 7750) should be allowed to install or replace this equipment.
Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.
Warning The device is designed to work with TN power systems.
Warning The SPE contains a lithium battery. There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
ESD Safety Precautions
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD occurs when electronic printed circuit cards are improperly handled. ESD can result in complete or intermittent failures. Always follow these ESD-prevention procedures when removing and replacing cards and other system components:
•Ensure that the chassis is electrically connected to earth ground.
•Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact.
•Connect the clip to an unpainted surface of the chassis frame to safely channel ESD voltages to ground.
•To properly guard against ESD damage and shocks, the wrist strap must be used correctly. If no wrist strap is available, ground yourself by touching the metal part of the chassis.
Caution For safety, periodically check the resistance value of the antistatic strap, which should be between 1 and 10 megohms (Mohms).
Caution Static voltages as low as 30 volts can cause latent damage to circuitry. Be sure to observe all standard antistatic procedures (for example, wear a grounding strap) when handling electronic equipment and components.
Warning Blank faceplates (filler panels) serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards and faceplates are in place.
Safety with Electricity
Follow these guidelines when working on equipment powered by electricity:
•Locate the emergency power-off switch in the room in which you are working. Then, if an electrical accident occurs, you can quickly shut the power off.
•Disconnect all power before installing or removing a Cisco ICS 7750 chassis.
•Do not work alone if potentially hazardous conditions exist.
•Never assume that power is disconnected from a circuit. Always check.
•Look carefully for possible hazards in your work area, such as moist floors, ungrounded power extension cables, and missing safety grounds.
If an electrical accident occurs, proceed as follows:
•Use caution; do not become a victim yourself.
•Turn off power to the chassis.
•If possible, send another person to get medical aid. Otherwise, determine the condition of the victim, and then call for help.
•Determine whether the victim needs rescue breathing or external cardiac compressions; then take appropriate action.
Ground Conductor Warning
|
Warning Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.
|
Waarschuwing
|
De aardingsleiding mag nooit buiten werking gesteld worden en de apparatuur mag nooit bediend worden zonder dat er een op de juiste wijze geïnstalleerde aardingsleiding aanwezig is. Neem contact op met de bevoegde instantie voor elektrische inspecties of met een elektricien als u niet zeker weet of voor passende aarding gezorgd is.
|
Varoitus
|
Älä koskaan ohita maajohdinta tai käytä laitteita ilman oikein asennettua maajohdinta. Ota yhteyttä asianmukaiseen sähkötarkastusviranomaiseen tai sähköasentajaan, jos olet epävarma maadoituksen sopivuudesta.
|
Attention
|
Ne jamais rendre inopérant le conducteur de masse ni utiliser l'équipement sans un conducteur de masse adéquatement installé. En cas de doute sur la mise à la masse appropriée disponible, s'adresser à l'organisme responsable de la sécurité électrique ou à un électricien.
|
Warnung
|
Umgehen Sie auf keinen Fall den Erdungsleiter und nehmen Sie die Geräte nicht in Betrieb, wenn der Erdungsleiter nicht sachgemäß installiert ist. Wenden Sie sich an die entsprechende Behörde, die für die Inspektion elektrischer Anlagen zuständig ist, oder an einen Elektriker, wenn Sie nicht sicher sind, ob der Anschluß ordnungsgemäß geerdet ist.
|
Avvertenza
|
Non escludere mai il conduttore di protezione né usare l'apparecchiatura in assenza di un conduttore di protezione installato in modo corretto. Se non si sa con certezza che è disponibile un collegamento di messa a terra adeguato, esaminare le Norme CEI pertinenti o rivolgersi a un elettricista qualificato.
|
Advarsel
|
Jordingslederen må aldri hindres, og utstyret må aldri brukes uten at en forsvarlig jordingsleder er installert. Kontakt elektrisitetstilsynet eller en elektriker dersom du er usikker på om riktig jording er tilgjengelig.
|
Aviso
|
Nunca anule o condutor à terra nem opere o equipamento sem ter um condutor à terra adequadamente instalado. Em caso de dúvida em relação ao sistema de ligação à terra, contacte os serviços locais de inspecção eléctrica ou um electricista qualificado.
|
¡Advertencia!
|
No desactive nunca el conductor de tierra ni opere el equipo sin un conductor de tierra instalado correctamente. Póngase en contacto con las autoridades de inspección eléctrica pertinentes o con un electricista, si no está seguro de contar con una toma de tierra adecuada.
|
Varning!
|
Koppla aldrig från jordledningen och använd aldrig utrustningen utan en på lämpligt sätt installerad jordledning. Om det föreligger osäkerhet huruvida lämplig jordning finns skall elektrisk besiktningsauktoritet eller elektriker kontaktas.
|
Use Copper Conductors Only
|
Warning Use copper conductors only.
|
Waarschuwing
|
Gebruik alleen koperen geleiders.
|
Varoitus
|
Käytä vain kuparijohtimia.
|
Attention
|
Utilisez uniquement des conducteurs en cuivre.
|
Warnung
|
Verwenden Sie ausschließlich Kupferleiter.
|
Avvertenza
|
Usate unicamente dei conduttori di rame.
|
Advarsel
|
Bruk bare kobberledninger.
|
Aviso
|
Utilize apenas fios condutores de cobre.
|
¡Advertencia!
|
Emplee sólo conductores de cobre.
|
Varning!
|
Använd endast ledare av koppar.
|
Electrical Storm Warning
|
Warning Never install telephone wiring during an electrical storm.
|
Waarschuwing
|
Installeer telefoondraden nooit tijdens een onweersbui.
|
Varoitus
|
Älä asenna puhelinjohtoja ukkosmyrskyn aikana.
|
Attention
|
Ne jamais installer des câbles téléphoniques pendant un orage.
|
Warnung
|
Installieren Sie eine Telefonverkablung niemals während eines Gewitters!
|
Avvertenza
|
Mai installare cavi telefonici durante un temporale elettrico.
|
Advarsel
|
Telefonledninger skal aldri monteres i tordenvær.
|
Aviso
|
Nunca instalar fios telefónicos durante uma tempestade eléctrica.
|
¡Advertencia!
|
Nunca instale el cableado del teléfono durante una tormenta.
|
Varning!
|
Telefonledningar får aldrig anslutas under åskväder.
|
Telephone Jacks in Wet Locations Warning
|
Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
|
Waarschuwing
|
Installeer telefoonaansluitingen nooit op vochtige locaties tenzij de aansluiting speciaal bestemd is voor vochtige locaties.
|
Varoitus
|
Älä asenna puhelimen pistokkeita kosteisiin tiloihin, ellei pistokkeita ole nimenomaisesti suunniteltu tällaisiin tiloihin.
|
Attention
|
Ne jamais installer de prises téléphoniques dans un local humide, sauf si celles-ci sont spécifiquement conçues pour cet usage.
|
Warnung
|
Telefonanschlüsse niemals in feuchten Umgebungen installieren, es sei denn der Anschluß ist speziell für Feuchtumgebungen entwickelt!
|
Avvertenza
|
Mai installare un jack telefonico in una zona bagnata almeno che il jack sia appositamente per zone bagnate.
|
Advarsel
|
Telefonkontakter skal aldri monteres i fuktige omgivelser, med mindre kontakten er spesielt laget for våtrom.
|
Aviso
|
Nunca instalar tomadas telefónicas em locais húmidos, a menos que a tomada tenha sido especialmente concebida para esse efeito.
|
¡Advertencia!
|
Nunca instale las rosetas del teléfono en zonas mojadas a menos que la roseta se diseñe específicamente para estas.
|
Varning!
|
Endast specialkonstruerat telefonjack får installeras i våtutrymme.
|
Uninsulated Wires and Terminals Warning
|
Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
|
Waarschuwing
|
Raak ongeïsoleerde telefoondraden of contacten nooit aan tenzij de telefoonlijn van de netwerkinterface werd ontkoppeld.
|
Varoitus
|
Älä kosketa eristämättömiä puhelinjohtoja tai liittimiä, ellei puhelinta ole irrotettu verkkoliittymästä.
|
Attention
|
Ne jamais toucher un câble téléphonique non isolé lorsque celui-ci est connecté au port réseau.
|
Warnung
|
Niemals nicht-isolierte Telefonkabel berühren, außer wenn die Telefonleitung an der Netzwerkschnittstelle abgetrennt wurde!
|
Avvertenza
|
Mai toccare cavi telefonici o terminali non isolati almeno che le linee telefoniche non siano state disconnesse dall'interfaccia rete.
|
Advarsel
|
Telefonledninger eller -uttak som ikke er isolert, må aldri berøres, med mindre telefonlinjen er frakoplet telenettet.
|
Aviso
|
Nunca tocar em fios ou terminais telefónicos não isolados, a menos que a linha telefónica tenha sido desligada ao nível da interface da rede.
|
¡Advertencia!
|
Nunca toque los alambres o los terminales del teléfono a menos que la línea telefónica se haya desconectado en el interfaz de la red.
|
Varning!
|
Telefonlinjer måste frånkopplas vid nätverksgränssnittet innan oisolerad telefonledning eller -uttag vidrörs.
|
Line Installation or Modification Warning
|
Warning Use caution when installing or modifying telephone lines.
|
Waarschuwing
|
Wees voorzichtig bij het installeren of modificeren van telefoonlijnen.
|
Varoitus
|
Ole varovainen, kun asennat puhelinlinjoja tai teet niihin muutoksia.
|
Attention
|
Une extrême prudence est recommandée lors de l'installation ou de la modification de lignes téléphoniques.
|
Warnung
|
Achtung bei der Installation und Modifikation von Telefonleitungen!
|
Avvertenza
|
Installate o modificate le linee telefoniche con molta cautela.
|
Advarsel
|
Det må utvises forsiktighet ved montering eller justering av telefonlinjer.
|
Aviso
|
Tomar as devidas precauções ao instalar ou alterar linhas telefónicas.
|
¡Advertencia!
|
Precaución al instalar o modificar las líneas telefónicas.
|
Varning!
|
Iakttag försiktighet vid installation eller modifiering av telefonlinjer.
|
Telephone Use During an Electrical Storm Warning
|
Warning Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
|
Waarschuwing
|
Gebruik nooit een telefoon (tenzij het een draadloze telefoon is) tijdens onweer. Er bestaat een kleine kans op een elektrische schok door bliksem.
|
Varoitus
|
Vältä puhelimen (muun kuin langattoman puhelimen) käyttöä ukkosmyrskyn aikana. Salamoinnista voi aiheutua sähköiskuvaara.
|
Attention
|
Pour éviter tout risque de choc électrique lors d'un orage, il est recommandé de ne pas utiliser un téléphone autre qu'un appareil sans fil.
|
Warnung
|
Vermeiden Sie die Benutzung eines Telefons während eines Gewitters (außer eines schnurlosen Geräts). Es besteht ein geringes Risiko eines elektrischem Schlags durch Blitze.
|
Avvertenza
|
Non utilizzate il telefono (almeno che sia cellulare) durante un temporale elettrico. Ci sono rischi, anche se poco probabili, di scariche elettriche dovute a fulmini.
|
Advarsel
|
Unngå å bruke telefonen (med mindre den er trådløs) i tordenvær. Det eksisterer en minimal risiko for elektrisk støt grunnet lynnedslag.
|
Aviso
|
Evitar a utilização do telefone (que não seja do tipo sem fios) durante uma tempestade eléctrica. Pode haver o risco remoto de choque eléctrico provocado pelo relâmpago.
|
¡Advertencia!
|
Evite usar el teléfono (a excepción de un teléfono inalámbrico) durante una tormenta. Puede correr peligro por la descarga eléctrica que emite el relámpago.
|
Varning!
|
Undvik att telefonera (gäller ej trådlös telefon) under åskväder. Viss risk finns för elstöt vid blixtnedslag.
|
Telephone Use by Gas Leaks Warning
|
Warning Do not use a telephone to report a gas leak in the vicinity of the leak.
|
Waarschuwing
|
Gebruik nooit een telefoon om een gaslek te melden als de telefoon zich in de buurt van het gaslek bevindt.
|
Varoitus
|
Älä ilmoita kaasuvuodosta puhelimitse, jos olet vuodon lähettyvillä.
|
Attention
|
Ne jamais utiliser un téléphone près d'une fuite de gaz pour signaler cette fuite à votre société de distribution.
|
Warnung
|
Um ein Leck in einer Gasleitung zu melden, benutzen Sie nicht ein Telefongerät in der Nähe des Lecks.
|
Avvertenza
|
Non utilizzate un telefono per avvertire di una perdita di gas nelle vicinanze della perdita.
|
Advarsel
|
Du skal ikke bruke telefon til å melde fra om en gasslekkasje i nærheten av denne lekkasjen.
|
Aviso
|
Não utilizar o telefone para comunicar uma fuga de gás nas proximidades dessa fuga.
|
¡Advertencia!
|
No utilice un teléfono para informar de un escape de gas en la zona.
|
Varning!
|
Telefonera ej i närheten vid rapportering om gasläcka.
|
Installation Hazard
|
Warning This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260. Incorrectly connecting this equipment to a general purpose outlet could be hazardous. The telecommunications lines must be disconnected 1) before unplugging the main power connector and/or 2) while the housing is open.
|
Waarschuwing
|
Deze uitrusting dient geïnstalleerd en onderhouden te worden door onderhoudspersoneel zoals gedefinieerd door AS/NZS 3260. Als deze uitrusting onjuist op een stopcontact voor algemeen gebruik wordt aangesloten kan dit gevaarlijk zijn. De telecommunicatielijnen dienen ontkoppeld te worden 1) voordat de stekker naar de hoofdstroomtoevoer eruit wordt genomen en/of 2) terwijl de behuizing open is.
|
Varoitus
|
Huoltohenkilöstön on asennettava ja huollettava tämä laite AS/NZS 3260:n määräysten mukaisesti. Laitteen virheellinen kytkeminen yleispistorasiaan voi aiheuttaa vaaratilanteita. Tietoliikennejohdot on irrotettava 1) ennen kuin päävirtaliitin irrotetaan pistorasiasta ja/tai 2) kun kotelo on auki.
|
Attention
|
Cet équipement ne doit être installé et entretenu que par du personnel d'entretien comme défini par la réglementation AS/NZS 3260. Un branchement incorrect de cet équipement à une prise de courant peut créer une situation dangereuse. Les lignes de télécommunications doivent être déconnectées 1) avant de débrancher le connecteur d'alimentation principal et/ou 2) lorsque le boîtier est ouvert.
|
Warnung
|
Dieses Gerät ist nur von ausgebildetem Personal zu installieren und zu warten (lt. Definition in AS/NZS 3260). Fälschliches Anschließen des Geräts an eine normale Steckdose könnte gefährlich sein. Die Telekommunikationsleitungen dürfen 1) beim Herausziehen des Netzsteckers und/oder 2) bei geöffnetem Gehäuse nicht angeschlossen sein.
|
Avvertenza
|
Questo apparecchio deve essere installato e mantenuto in efficienza esclusivamente da personale tecnico che soddisfi i requisiti specificati nelle norme AS/NZS 3260. Un collegamento errato di questo apparecchio ad una presa di uso generale può essere pericoloso. Le linee di telecomunicazione vanno scollegate sia prima di scollegare la spina dell'alimentazione di rete sia prima di aprire l'involucro (non ricollegarle finché non si chiude l'involucro).
|
Advarsel
|
Dette utstyret må monteres og vedlikeholdes av vedlikeholdspersonell i henhold til AS/NZS 3260. Feilaktig tilkopling av dette utstyret til et vanlig strømuttak kan medføre fare. Telekommunikasjonslinjene må være frakoplet 1) før strømledningen trekkes ut av kontakten og/eller 2) mens huset er åpent.
|
Aviso
|
A instalação e a manutenção deste equipamento devem ser realizadas por pessoal da assistência, conforme definido na norma AS/NZS 3260. A ligação incorrecta deste equipamento a uma tomada de utilização geral poderá ser perigosa. As linhas de telecomunicações têm de estar desligadas 1) antes de desligar a ligação à corrente principal e/ou 2) enquanto a caixa estiver aberta.
|
¡Advertencia!
|
Este equipo se debe instalar y mantener solamente por personal de servicio, según definido por AS/NZS 3260. La conexión incorrecta de este equipo a una toma o receptáculo de tipo general podría resultar peligrosa. Las líneas de telecomunicaciones deben desconectarse 1) antes de desenchufar el conector principal de energía y 2) mientras la caja esté abierta.
|
Varning!
|
Denna utrustning måste installeras och underhållas av servicepersonal enligt AS/NZS 3260. Felaktig anslutning av denna utrustning till ett vanligt vägguttag kan medföra fara. Teleledningarna måste kopplas ifrån innan väggkontakten dras ut och/eller innan höljet tas av.
|
Grounding Requirement Warning
|
Warning This equipment needs to be grounded. Use a green and yellow 14 AWG ground wire to connect the host to earth ground during normal use.
|
Waarschuwing
|
Deze apparatuur hoort geaard te woden. Gebruik een groen/gele 14 AWG aarddraad om de host tijdens normaal gebruik met de aarde te verbinden.
|
Varoitus
|
Tämä laitteisto täytyy maadoittaa. Yhdistä isäntälaite maahan normaalikäytön aikana käyttämällä vihreä-keltaista 14 AWG -maadoitusjohtoa.
|
Attention
|
Cet équipement doit être relié à la terre. Utilisez un fil vert et jaune de gabarit 14 (AWG) pour connecter l'hôte à la terre lors son utilisation normale.
|
Warnung
|
Dieses Gerät muß geerdet werden. Verwenden Sie ein grün/gelbes 14-AWG-Erdungskabel, um damit das Host-Gerät während des normalen Betriebs zu erden.
|
Avvertenza
|
Questa apparecchiatura deve essere collegata a massa. Durante l'uso normale, collegare l'host alla massa di terra usando un filo di massa verde e giallo di diametro pari a 14 AWG.
|
Advarsel
|
Dette utstyret må jordes. Bruk en grønn og gul 14 AWG jordledning til å kople vertsterminalen til jording i løpet av normalt bruk.
|
Aviso
|
É necessário que este equipamento esteja ligado à terra. Utilize um fio de ligação à terra de 14 AWG, verde e amarelo, para ligar o host à ligação à terra durante a sua utilização normal.
|
Advertencia
|
Este equipo debe conectarse a tierra. Utilizar un hilo de puesta a tierra 14 AWG verde y amarillo para conectar a tierra el equipo principal durante el uso normal.
|
Varning!
|
Denna utrustning är avsedd att jordas. Använd en gulgrön jordledning av storlek 14 AWG till att jorda värdenheten vid normal användning.
|
Figure 1 shows the grounding stud that is located on the back of the Cisco ICS 7750 chassis.
Figure 1 Grounding Stud on the Cisco ICS 7750 Chassis
More Than One Power Supply Warning
|
Warning This unit might have more than one power supply connection. All connections need to be removed to de-energize the unit.
|
Waarschuwing
|
Deze eenheid kan meer dan één stroomtoevoerverbinding bevatten. Alle verbindingen dienen ontkoppeld te worden om de eenheid te ontkrachten.
|
Varoitus
|
Tässä laitteessa voi olla useampia kuin yksi virtakytkentä. Kaikki liitännät on irrotettava, jotta jännite poistetaan laitteesta.
|
Attention
|
Pour supprimer toute tension et tout courant électrique de l'unité, TOUTES les connexions d'alimentation doivent être débranchées.
|
Warnung
|
Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, daß der Einheit kein Strom zugeführt wird, müssen alle Verbindungen entfernt werden.
|
Avvertenza
|
Questo prodotto può avere più di una connessione di alimentazione elettrica. Tutte le connessioni devono essere staccate per togliere la corrente dal prodotto.
|
Advarsel
|
Denne enheten kan ha mer enn én strømtilførselskobling. Alle koblinger må fjernes fra enheten for å utkoble all strøm.
|
Aviso
|
Esta unidade poderá ter mais do que uma conexão de fonte de energia. Todas as conexões necessitam de ser removidas para desactivar a unidade.
|
¡Advertencia!
|
Esta unidad puede contar con más de una conexión para fuentes de alimentación. Para cortar por completo el suministro de energía, deben desconectarse todas las conexiones.
|
Varning!
|
Denna enhet har eventuellt mer än en strömförsörjningsanslutning. Alla anslutningar måste tas bort för att göra enheten strömlös.
|
Telephone Wiring Guidelines
Follow these guidelines when working with any equipment that is connected to telephone wiring or to other network cabling:
•Never install telephone wiring during a lightning storm.
•Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
•Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
•Use caution when installing or modifying telephone lines.
•Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
•Use caution when installing or modifying telephone lines.
Lifting and Reaching Safety Precautions
Follow these guidelines when lifting or moving the chassis:
Warning To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to support the weight of the unit. Lift the unit only by using handles that are an integral part of the chassis, or by grasping the chassis underneath its lower edge.
Warning Two people are required to lift the chassis. To prevent injury, keep your back straight and lift with your legs, not your back.
Note SAVE THESE INSTRUCTIONS.
System Component Identification
Figure 2 shows the major components in a typical Cisco ICS 7750:
•Slots 1 through 6 can contain a combination of SPEs, ASIs, and MRPs.
•Slot 7 must contain only an SSP.
•Slot 8 must contain only an SAP.
•The Power Supply 1 and Power Supply 2 slots can each contain a power supply module (only one power supply module is required to operate the system).
•The system contains one fan tray, at the bottom of the chassis.
Note By factory-installed default, the Cisco ICS 7750 chassis comes with the SPE running System Manager installed in slot 6, and with SPEs populated from right to left. Other system cards (such as MRPs and ASIs) are populated from left to right in the chassis.
Figure 2 Cisco ICS 7750
Removing and Replacing Cisco ICS 7750 Components
This section provides general information about removing and replacing the Cisco ICS 7750 components. This section contains the following subsections:
•Best Practices for Hot Swapping
•Best Practices for Card Replacement
For detailed instructions for removing and replacing system components, see the following sections:
•Removing and Replacing SPE310s
•Removing and Replacing ASIs, MRPs, the SSP, or the SAP
•Removing and Replacing Power Supply Modules
•Removing and Replacing the Fan Tray
Warning When performing the procedures in this section, wear grounding wrist straps to avoid ESD damage to the Cisco ICS 7750. Do not directly touch the backplane with your hand or any metal tool to prevent personal injury or equipment damage.
Warning Removing cards, fans, and power supply modules can expose you to high-energy (high-amperage) circuits and possible ejection of molten metal or to the shock hazard of telephony circuit voltages. Be sure to remove all rings, watches, and other jewelry from fingers, wrists, and arms before removing panels and devices.
Note If the chassis has any empty slots, they are covered with blank panels when the Cisco ICS 7750 is shipped to you. Do not remove the panel covering an empty slot until you are ready to install a card in the slot.
Note You do not have to disassemble any system component or remove the chassis from the rack to perform any of the procedures described in this section.
Best Practices for Hot Swapping
You can hot swap cards while the Cisco ICS 7750 is operating. With hot swapping, you do not need to power down the system. However, be sure to read and follow the best practices in this section and in the "Best Practices for Card Replacement" section, and the specific instructions for removing and replacing each type of card or module before you hot swap it.
Warning Only trained and qualified (IP Telephony certified for the Cisco ICS 7750) personnel should be allowed to install or replace this equipment.
Caution When replacing a hot-swappable system card, you do not need to power down the entire chassis by using the chassis power supply switch or by unplugging the power supply. Powering down the entire chassis may cause the Cisco ICS 7750 to lose important configuration data and will interrupt any applications or functions running on other cards in the chassis. (The one exception to this is an electrical accident, in which case turning off the power is recommended; see the
"Safety with Electricity" section.)
Caution You can install only one SAP and one SSP in a single Cisco ICS 7750 chassis. If you must hot swap the SAP, the cooling fans do not operate; the system's ability to detect alarms associated with the operating environment, fans, and power supply modules is degraded; and applications using the COM ports on the SAP lose their access to those ports, until an operational SAP is properly reinserted in the chassis. If you must hot swap the SSP, the system loses LAN connectivity, and calls being made from or to Cisco IP phones that are switched through that SSP are disconnected until an operational SSP is properly reinserted in the chassis.
Caution Depending on your system configuration, hot swapping of SPEs, ASIs, or MRPs can adversely affect users connected to the system.
For example, if Cisco CallManager is running on only one SPE, hot swapping that SPE disconnects calls to or from the PSTN and prevents the system from processing further PSTN traffic until an operational SPE is properly reinserted into the chassis. Similarly, hot swapping an ASI or MRP that is in the process of routing voice or WAN traffic prevents that traffic from reaching its destination. If you have a Flash-based MRP card configured as the only VLAN router and the MRP goes offline, all call processing might be lost (along with access to other IP devices). Disruption of call processing services may occur if the MRP is routing calls across VLANs. If fault tolerance is critical, you can use the Hot Standby Router Protocol (HSRP) for more reliable and redundant routing. For additional information about HSRP, refer to Hot Standby Router Protocol (HSRP) Features and Functionality.
Contact your Cisco sales representative for guidelines on installing cards and software on your system for maximum availability and redundancy.
Best Practices for Card Replacement
This section provides best practices for replacing system cards:
•Best Practices for Resetting or Removing Cards
•Best Practices for Inspecting the Chassis Backplane and Card Connectors Before Installing Cards
•Best Practices for Installing Cards
Best Practices for Resetting or Removing Cards
Consult these guidelines (and the instructions in "Best Practices for Hot Swapping") before resetting or removing cards:
•Check card LEDs before attempting to reset or remove a card.
•Do not press the SHTDN button on any card in the Cisco ICS 7750 chassis unless you are directed to do so.
Caution Always use the extractor levers to disengage cards from the chassis. Failure to use the levers can cause system error messages that indicate a card failure. However, do not use the extractor levers to lift or support the weight of the cards.
Best Practices for Inspecting the Chassis Backplane and Card Connectors Before Installing Cards
Before you install a card, perform the following inspections:
•Inspect the backplane for bent pins (see Figure 3) or bent dividers between rows.
If the backplane has bent pins, do not install a card in that slot. Installing a card into a damaged backplane slot will damage the connector on the card.
Figure 3 Backplane Inspection
•Inspect the card for damaged holes on the connector (see Figure 4).
If the connector has damaged holes, do not install the card. Installing a card that has a damaged connector will damage the backplane. Return damaged cards to Cisco (see the "RMA Return Instructions" section).
Figure 4 Card Connector Inspection
Best Practices for Installing Cards
When installing cards, consult these guidelines, and follow the card-specific instructions:
•Do not force the card faceplate into its slot. This action can damage the pins on the backplane if they are not aligned properly with the module or card.
•Before installing a card, be sure to align its top and bottom edges with the upper and lower card guides in the chassis slot. Do not attempt to push the card into its slot until its top and bottom edges are in proper alignment.
•When installing a card, carefully slide it all the way into the slot, and press both extractor levers inward (toward the center of the card) as far as they will go. The front of the card should now be flush with the other cards in the chassis. Using this method ensures that the card connector correctly mates with the backplane. For more information and an illustration on installing a card, see the "Installing an SPE" section.
If the card is particularly tight in its slot, or if the extractor lever engagement hooks are not engaging with the chassis, you might need to take the card out and insert it again to cause its extractor levers to engage properly.
Caution Do not push the card with so much force that it bends in the middle, since bending a card might force its sensitive electronic components to come in contact with adjacent cards.
•The card or module should be firmly seated in the slot. Any card or module that is only partially connected to the backplane can disrupt system operation.
•After card installation is complete, always use the lock-down screws (at the top and bottom of the card) to secure the card firmly in place in the chassis. If the screws do not engage, the extractor levers are not properly aligned, and the card is not firmly seated in the chassis. Remove and reinsert the card until you can fully tighten the screws.
Removing and Replacing SPE310s
This section describes how to determine the function of an SPE, tells how to install and replace SPEs, and contains the following subsections:
•Accessing the SPE310
•Removing an SPE
•Installing an SPE
•Verifying SPE Installation
•Configuring a New or Replacement SPE
•Downgrading ICS System Software
Note This document is not intended for use with SPE200s. If you need assistance with an SPE200, contact the Cisco Technical Assistance Center (see the "Technical Assistance Center" section).
Accessing the SPE310
You can access the SPE310 Windows interface to determine whether the SPE is running ICS System Soft
