Table Of Contents
Understanding System Message Logging
Configuring System Message Logging
Default System Message Logging Configuration
Disabling and Enabling Message Logging
Setting the Message Display Destination Device
Enabling and Disabling Time Stamps on Log Messages
Enabling and Disabling Sequence Numbers in Log Messages
Defining the Message Severity Level
Limiting Syslog Messages Sent to the History Table and to SNMP
Configuring UNIX Syslog Servers
Logging Messages to a UNIX Syslog Daemon
Configuring the UNIX System Logging Facility
Displaying the Logging Configuration
System Message Logging
This chapter describes how to configure system message logging on your wireless device.
This chapter consists of these sections:
•
Understanding System Message Logging
•
•
Note
Understanding System Message Logging
By default, access points send the output from system messages and debug privileged EXEC commands to a logging process. The logging process controls the distribution of logging messages to various destinations, such as the logging buffer, terminal lines, or a UNIX syslog server, depending on your configuration. The process also sends messages to the console.
Note
When the logging process is disabled, messages are sent only to the console. The messages are sent as they are generated, so message and debug output are interspersed with prompts or output from other commands. Messages are displayed on the console after the process that generated them has finished.
You can set the severity level of the messages to control the type of messages displayed on the console and each of the destinations. You can timestamp log messages or set the syslog source address to enhance real-time debugging and management.
You can access logged system messages by using the access point command-line interface (CLI) or by saving them to a properly configured syslog server. The access point software saves syslog messages in an internal buffer. You can remotely monitor system messages by accessing the access point through Telnet or by viewing the logs on a syslog server.
Configuring System Message Logging
This section describes how to configure system message logging. It contains this configuration information:
•
•
•
•
•
•
•
•
System Log Message Format
System log messages can contain up to 80 characters and a percent sign (%), which follows the optional sequence number or timestamp information, if configured. Messages are displayed in this format:
seq no:timestamp: %facility-severity-MNEMONIC:description
The part of the message preceding the percent sign depends on the setting of the service sequence-numbers, service timestamps log datetime, service timestamps log datetime [localtime] [msec] [show-timezone], or service timestamps log uptime global configuration command.
Table 6 describes the elements of syslog messages.
Table 6 System Log Message Elements
seq no:
Stamps log messages with a sequence number only if the service sequence-numbers global configuration command is configured.
For more information, see the "Enabling and Disabling Sequence Numbers in Log Messages" section.
timestamp formats:
mm/dd hh:mm:ss
or
hh:mm:ss (short uptime)
or
d h (long uptime)
Date and time of the message or event. This information appears only if the service timestamps log [datetime | log] global configuration command is configured.
For more information, see the "Enabling and Disabling Time Stamps on Log Messages" section.
facility
The facility to which the message refers (for example, SNMP, SYS, and so forth). A facility can be a hardware device, a protocol, or a module of the system software. It denotes the source or the cause of the system message.
severity
Single-digit code from 0 to 7 that is the severity of the message. For a description of the severity levels, see Table 8.
MNEMONIC
Text string that uniquely describes the message.
description
Text string containing detailed information about the event being reported.
The following example shows a partial access point system message:
00:00:46: %LINK-3-UPDOWN: Interface Port-channel1, changed state to up00:00:47: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to up00:00:47: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to up00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to down 2*Mar 1 18:46:11: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36)18:47:02: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36)*Mar 1 18:48:50.483 UTC: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36)Default System Message Logging Configuration
Table 7 shows the default system message logging configuration.
Table 7 Default System Message Logging Configuration
System message logging to the console
Enabled
Console severity
Debugging (and numerically lower levels; see Table 8)
Logging buffer size
4096 bytes
Logging history size
1 message
Time stamps
Disabled
Synchronous logging
Disabled
Logging server
Disabled
Syslog server IP address
None configured
Server facility
Local7 (see Table 9)
Server severity
Informational (and numerically lower levels; see Table 8)
Disabling and Enabling Message Logging
Message logging is enabled by default. It must be enabled to send messages to any destination other than the console. When enabled, log messages are sent to a logging process, which logs messages to designated locations asynchronously to the processes that generated the messages.
To disable message logging, follow these steps, beginning in privileged EXEC mode:
Disabling the logging process can slow down the access point because a process must wait until the messages are written to the console before continuing. When the logging process is disabled, messages are displayed on the console as soon as they are produced, often appearing in the middle of command output.
The logging synchronous global configuration command also affects the display of messages to the console. When this command is enabled, messages appear only after you press Return. For more information, see the "Enabling and Disabling Time Stamps on Log Messages" section.
To reenable message logging after it has been disabled, use the logging on global configuration command.
Setting the Message Display Destination Device
If message logging is enabled, you can send messages to specific locations in addition to the console. To specify the locations that receive messages, use one or more of the following commands, beginning in privileged EXEC mode:
Step 1
configure terminal
Enters global configuration mode.
Step 2
logging buffered [size] [level]
Logs messages to an internal buffer. The default buffer size is 4096. The range is 4096 to 2147483647 bytes. Levels include emergencies 0, alerts 1, critical 2, errors 3, warnings 4, notifications 5, informational 6, and debugging 7.
Note
Step 3
logging host
Logs messages to a UNIX syslog server host.
For host, specify the name or IP address of the host to be used as the syslog server.
To build a list of syslog servers that receive logging messages, enter this command more than once.
For complete syslog server configuration steps, see the "Configuring UNIX Syslog Servers" section.
Step 4
end
Returns to privileged EXEC mode.
Step 5
terminal monitor
Logs messages to a non-console terminal during the current session.
Terminal parameter-setting commands are set locally and do not remain in effect after the session has ended. You must perform this step for each session to see the debugging messages.
The logging buffered global configuration command copies logging messages to an internal buffer. The buffer is circular, so newer messages overwrite older messages after the buffer is full. To display the messages that are logged in the buffer, use the show logging command, in privileged EXEC mode. The first message displayed is the oldest message in the buffer. To clear the contents of the buffer, use the clear logging command, in privileged EXEC mode.
To disable logging to the console, use the no logging console command in global configuration mode. To disable logging to a file, use the no logging file [severity-level-number | type] command in global configuration mode.
Enabling and Disabling Time Stamps on Log Messages
By default, log messages are not time stamped.
To enable timestamping of log messages, follow these steps, beginning in privileged EXEC mode:
To disable timestamps for both debug and log messages, use the no service timestamps command in mode global configuration.
The following example shows part of a logging display with the service timestamps log datetime command enabled:
*Mar 1 18:46:11: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36)The follwoing example shows part of a logging display with the service timestamps log uptime command enabled:
00:00:46: %LINK-3-UPDOWN: Interface Port-channel1, changed state to upEnabling and Disabling Sequence Numbers in Log Messages
Because there is a chance that more than one log message can have the same timestamp, you can display messages with sequence numbers so that you can unambiguously refer to a single message. By default, sequence numbers in log messages are not displayed.
To enable sequence numbers in log messages, follow these steps, beginning in privileged EXEC mode:
Step 1
configure terminal
Enters global configuration mode.
Step 2
service sequence-numbers
Enables sequence numbers.
Step 3
end
Returns to privileged EXEC mode.
To disable sequence numbers, use the no service sequence-numbers global configuration command.
The follwoing example shows part of a logging display with sequence numbers enabled:
000019: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36)Defining the Message Severity Level
You can limit messages that are displayed to the selected device by specifying the severity level of the message. Table 8 describes the severity level.
To define the message severity level, follow these steps, beginning in privileged EXEC mode:
Step 1
configure terminal
Enters global configuration mode.
Step 2
logging console level
Limits messages logged to the console.
By default, the console receives debugging messages and numerically lower levels (see Table 8).
Step 3
logging monitor level
Limits messages logged to the terminal lines.
By default, the terminal receives debugging messages and numerically lower levels (see Table 8).
Step 4
logging trap level
Limits messages logged to the syslog servers.
By default, syslog servers receive informational messages and numerically lower levels (see Table 8).
For complete steps for configuring syslog servers, see the "Configuring UNIX Syslog Servers" section.
Step 5
end
Returns to privileged EXEC mode.
Note
To disable logging to the console, use the no logging console command in global configuration mode. To disable logging to a terminal other than the console, use the no logging monitor command in global configuration mode. To disable logging to syslog servers, use the no logging trap command in global configuration mode.
Table 8 describes the severity level keywords. It also lists the corresponding UNIX syslog definitions from the most severe level to the least severe level.
The software generates four other categories of messages:
•
•
•
•
Note
Limiting Syslog Messages Sent to the History Table and to SNMP
If you have enabled syslog message traps to be sent to an SNMP network management station by using the snmp-server enable trap command, you can change the level of messages sent and stored in the access point history table. You can also change the number of messages that are stored in the history table.
Messages are stored in the history table because SNMP traps are not guaranteed to reach their destination. By default, one message of the level warning and numerically lower levels (see Table 8) are stored in the history table even if syslog traps are not enabled.
To change the level and history table size defaults, follow these steps, beginning in privileged EXEC mode:
Step 1
configure terminal
Enters global configuration mode.
Step 2
logging history level1
Changes the default level of syslog messages stored in the history file and sent to the SNMP server.
See Table 8 for a list of level keywords.
By default, warnings, errors, critical, alerts, and emergencies messages are sent.
Step 3
logging history size number
Specifies the number of syslog messages that can be stored in the history table.
The default is to store one message. The range is 1 to 500 messages.
Step 4
end
Returns to privileged EXEC mode.
1 Table 8 lists the level keywords and severity level. For SNMP usage, the severity level values increase by 1. For example, emergencies equal 1, not 0, and critical equals 3, not 2.
When the history table is full (it contains the maximum number of message entries specified with the logging history size command in global configuration mode), the oldest message entry is deleted from the table to allow the new message entry to be stored.
To return the logging of syslog messages to the default level, use the no logging history command in global configuration mode. To return the number of messages in the history table to the default value, use the no logging history size command in global configuration mode.
Setting a Logging Rate Limit
You can set a limit on the number of messages that the access point logs per second. You can enable the limit for all messages or for messages sent to the console, and you can specify that messages of a specific severity are exempt from the limit.
To enable a logging rate limit, follow these steps, beginning in privileged EXEC mode:
To disable the rate limit, use the no logging rate-limit command in global configuration mode.
Configuring UNIX Syslog Servers
The next sections describe how to configure the 4.3 BSD UNIX server syslog daemon and define the UNIX system logging facility.
Logging Messages to a UNIX Syslog Daemon
Before you can send system log messages to a UNIX syslog server, you must configure the syslog daemon on a UNIX server. Log in as root, and perform these steps.
Note
Step 1
local7.debug /usr/adm/logs/cisco.logThe local7 keyword specifies the logging facility to be used; see Table 9 for information on the facilities. The debug keyword specifies the syslog level; see Table 8 for information on the severity levels. The syslog daemon sends messages at this level or at a greater severity level to the file specified in the next field. The file must already exist, and the syslog daemon must have permission to write to it.
Step 2
$ touch /usr/adm/log/cisco.log$ chmod 666 /usr/adm/log/cisco.logStep 3
$ kill -HUP `cat /etc/syslog.pid`For more information, see the man syslog.conf and man syslogd commands on your UNIX system.
Configuring the UNIX System Logging Facility
When sending system log messages to an external device, you can cause the access point to identify its messages as originating from any of the UNIX syslog facilities.
To configure UNIX system facility message logging, follow these steps, beginning in privileged EXEC mode:
Step 1
configure terminal
Enters global configuration mode.
Step 2
logging host
Logs messages to a UNIX syslog server host by entering its IP address.
To build a list of syslog servers that receive logging messages, enter this command more than once.
Step 3
logging trap level
Limits messages logged to the syslog servers.
Be default, syslog servers receive informational messages and lower. See Table 8 for level keywords.
Step 4
logging facility facility-type
Configures the syslog facility. See Table 9 for facility-type keywords.
The default is local7.
Step 5
end
Returns to privileged EXEC mode.
To remove a syslog server, use the no logging host command in global configuration mode, and specify the syslog server IP address. To disable logging to syslog servers, enter the no logging trap command in global configuration mode.
Table 9 lists the 4.3 BSD UNIX system facilities that the Cisco IOS software supports. For more information about these facilities, consult the operator's manual for your UNIX operating system.
Displaying the Logging Configuration
To display the current logging configuration and the contents of the log buffer, use the show logging command in privileged EXEC mode. For information about the fields in this display, refer to the Cisco IOS Configuration Fundamentals Command Reference for Release 12.2.
To display the logging history file, use the show logging history command in privileged EXEC mode.
