Table Of Contents

dspimagrp

dspimagrps

dspimagrpalm

dspimagrpalms

dspimagrpalmcnt

dspimagrpbucketcnt

dspimagrpcnt

dspimalnk

dspimalnks

dspimalnkalm

dspimalnkalms

dspimalnkbucketcnt

dspimalnkcnt

dspingbucketcnt

dsplmi

dsplmis

dsplmistat

dspln

dspln

dsplns

dsplns

dsplnbucketcnt

dsplncnt

dsplnload

dsplnpmbucketcnt

dspload

dspmcastload

dsppart

dspparts

dsppath

dsppaths

dsppathalm

dsppathalms

dsppathalmcnf

dsppathalmcnt

dspport

dspports

dspportbucketcnt

dspportcnt

dspportload

dspportsct

dspqecnfcnt

dsprmalms

dsprminfo

dsprmrsrc

dsprmrsrcs

exit

help (?)

history

insbiterror

logout

offdiagstat

ondiagstat

ping

reboot

restartimagrp (rstrtimagrp)

rrtcon

setsctver

startbert

startimalnktst

stopbert

stopimalnktst

switchapsln

timeout

tstconseg

tstdelay

upallports

upcon

upilmi

upimagrp

uplmi

upln

uppath

upport

users

who

whoami

dspimagrp

Display IMA Group—AXSM-32-T1E1-E

Displays the following configuration information for the specified IMA group.

Information	Description
IMA group number	The number of the IMA group you provide to dspimagrp.
NE IMA version	The IMA version at the near end (was specified by addimagrp).
Group symmetry	The group symmetry mode adjusted during the group start-up.
Minimum links in TX direction	The minimum number of links that must be active on the transmit side for the IMA group to be operational.
Minimum links in RX direction	The minimum number of links that must be active on the receive side for the IMA group to operational.
NE TX clock mode	The transmit clocking mode used by the near-end IMA group.
FE TX clock mode	The transmit clocking mode used by the far-end IMA group.
TX Frame length	The frame length used by the IMA group in the transmit direction.
RX Frame length	The frame length used by the IMA group in the receive direction.
Group GTSM	The current state of the IMA group (the GTSM state).
NE group state	The state of the near-end IMA group. For example: start-up state.
FE group state	The state of the far-end IMA group. For example: start-up state.
Group failure status	Could be near end state is unknown, failed, start-up, etc.
TX IMA ID	The IMA ID currently in use by the near-end IMA function.
RX IMA ID	The IMA ID currently in use by the far-end IMA function.
Max cell rate	The maximum number of cells per second for this IMA group.
Avail cell rate	The amount of bandwidth in cells per second available to this group.
Differential delay maximum	The maximum number of milliseconds of differential delay among the links that are tolerated on this interface.
Diff delay maximum observed	The latest maximum differential delay (in milliseconds) observed between the links having the least and most link propagation delay, among the receive links currently configured in the IMA group.
Accumulated delay	The accumulated delay for the current IMA group in milliseconds.
GTSM up integration time	Integration UP time for alarm integration. Persisting checking time to enter a failure alarm condition, in case of LIF, LODS, RFI-IMA fault failure alarms. Units of measure are milliseconds.
GTSM down integration time	Integration DOWN time for alarm integration. Persisting clearing time to exit the LIF, LODS, RFI-IMA failure alarm conditions. Units of measure are milliseconds.
Number TX configured links	The number of transmit links that are configured in this IMA group.
Number RX configured link	The number of receive links that are configured in this IMA group.
Number of active TX links	The number of transmit links that are active in this IMA group.
Number of actual RX links	The number of receive links that are active in this IMA group.
Least delay link	The ifIndex of the link configured in the IMA group that has the smallest link propagation delay. A value of zero may appear if no link has been configured in the IMA group or if the link with the smallest link propagation delay has not yet been determined.
Tx timing reference link	The ifIndex of the transmit timing reference link used by the near-end for IMA data cell clock recovery from the ATM layer. A value of zero may appear if no link has been configured in the group or if the transmit timing reference link has not yet been selected.
Rx timing reference link	The ifIndex of the receive timing reference link used by the near-end for IMA data cell clock recovery toward the ATM layer. A value of zero may appear if no link has been configured in the group or if the receive timing reference link has not yet been selected.
Group running seconds	The number of seconds the local IMA group has been running.
Alpha value	This is the 'alpha' value used to specify the number of consecutive invalid ICP cells to be detected before moving to the IMA Hunt state from the IMA Sync state.
Beta value	This is the 'beta' value used to specify the number of consecutive errored ICP cells to be detected before moving to the IMA Hunt state from the IMA Sync state.
Gamma value	This is the 'gamma' value used to specify the number of consecutive valid ICP cells to be detected before moving to the IMA Sync state from the IMA PreSync state.
TX OAM label	IMA OAM Label value transmitted by the near-end IMA unit.
RX OAM label	IMA OAM Label value transmitted by the far-end IMA unit. A 0 likely means that the IMA unit has not yet received an OAM label from the far-end IMA unit.
Test pattern procedure status	The current link test procedure status—enabled or disabled, for example.
Test link	The current link under test
Test pattern	The current link test pattern

Syntax

dspimagrp <group>

Syntax Description

group

The bay number (1-2) and the IMA group number (1-16) in the format bay.group. For example: 1.16

Related Commands

addimagrp, delimagrp, dspimagrpcnt, dspimagrps, cnfimagrp, rstrtimagrp, dspimalnk, addimalnk, delimalnk

Attributes

Log: no

State: active

Privilege: ANYUSER

Example

Display the configuration for bay 1, group 1.

MGX8850.10.AXSME.a > dspimagrp 1.1

    Group Number                    : 1.1

    NE IMA Version                  : Version 1.0

    Group Symmetry                  : Symm  Operation

    Tx Min Num Links                : 1

    Rx Min Num Links                : 1

    NE TX Clk Mode                  : CTC

    FE TX Clk Mode                  : ITC

    Tx Frame Len                    : 128

    Rx Frame Len                    : 128

    Group GTSM                      : Down

    NE Group State                  : CfgAbort-Unsupp-ImaVer

    FE Group State                  : StartUp

    Group Failure Status            : StartUp FE

    Tx Ima Id                       : 11

    Rx Ima Id                       : 1

    Max Cell Rate (c/s)             : 8980

    Avail Cell Rate (c/s)           : 0

    Diff Delay Max  (msecs)         : 220

    Diff Delay Max Observed (msecs) : 0

    Accumulated Delay (msecs)       : 0

    Clear Accumulated Delay Status  : Not In Progress

    GTSM Up Integ time(msecs)       : 10

    GTSM Dn Integ time(msecs)       : 1000

    Num Tx Cfg Links                : 2

    Num Rx Cfg Links                : 2

    Num Act Tx Links                : 0

    Num Act Rx Links                : 0

    Least Delay Link                : Unknown

    Tx Timing Ref Link              : 1.1

    Rx Timing Ref Link              : Unknown

    Group Running Secs              : 0

    Alpha Val                       : 2

    Beta Val                        : 2

    Gamma Val                       : 1

    Tx OAM Label                    : 1

    Rx OAM Label                    : 0

    Test Pattern Procedure Status   : Disabled

    Test Link                       : Unknown

    Test Pattern                    : 255

    Stuff Cell Indication (frames)  : 1

MGX8850.10.AXSME.a >

dspimagrps

Display IMA Groups—AXSM-32-T1E1-E

Displays the following information for all configured IMA groups:

Information	Description
IMA group number	The configured IMA group number. This number is same as port number.
minimum links	Minimum number of active links required for the IMA group to be operational.
transmit M	Transmit frame length
receive M	Receive frame length
transmit clock mode	ITC, CTC
maximum differential delay	in mSec
Near-End IMA state	The current operational state of the near-end IMA Group State Machine.
Far-End IMA state	The current operational state of the far-end IMA Group State Machine.
IMA ver	The version of IMA in use by the IMA group.

Syntax

dspimagrps

Syntax Description

No parameters

Related Commands

dspimagrp

Attributes

Log: no

State: active

Privilege: ANYUSER

Example

MGX8850.2.AXSME.a > dspimagrps

Ima  Min  Tx   Rx   Tx   Diff                NE-IMA                  FE-IMA  IMA

Grp  Lnks Frm  Frm  Clk  Delay                state                   state  Ver

          Len  Len  Mode (ms)

--------------------------------------------------------------------------------

1.14  16  128  128  CTC  100 CfgAbort-Unsupp-ImaVer  CfgAbort-Unsupp-ImaVer  1.0

1.15   2  256  256  CTC  275            Operational             Operational  1.1

1.16   2  256  256  CTC  100           Insuff Links            Insuff Links  1.1 

dspimagrpalm

Display IMA Group Alarm—AXSM-32-T1E1-E

Displays the group number and alarm state for the specified IMA group. The possible alarms are as follows:

•imaAlarmLinkLif (1)

•imaAlarmLinkLods (2)

•imaAlarmLinkRfi (3)

•imaAlarmLinkTxMisConnect (4)

•imaAlarmLinkRxMisConnect (5)

•imaAlarmLinkTxFault (6)

•imaAlarmLinkRxFault (7)

•imaAlarmLinkTxUnusableFe (8)

•imaAlarmLinkRxUnusableFe (9)

•imaAlarmGroupStartupFe (10)

•imaAlarmGroupCfgAbort (11)

•imaAlarmGroupCfgAbortFe (12)

•imaAlarmGroupInsuffLinks (13)

•imaAlarmGroupInsuffLinksFe (14)

•imaAlarmGroupBlockedFe (15)

•imaAlarmGroupTimingSynch (16)

Syntax

dspimagrpalm <group>

Syntax Description

group

The bay number (1-2) and the IMA group number (1-16) in the format bay.group. For example: 1.16

Related Commands

dspimagrpalms

Attributes

Log: no

State: active

Privilege: ANYUSER

Example

Display the alarms for bay 1, group 16.

MGX8850.2.AXSME.a > dspimagrpalm 1.16

dspimagrpalms

Display IMA Group Alarms—AXSM-32-T1E1-E

Displays the group number and alarm state for each configured IMA group. The possible alarms are as follows:

•imaAlarmLinkLif (1)

•imaAlarmLinkLods (2)

•imaAlarmLinkRfi (3)

•imaAlarmLinkTxMisConnect (4)

•imaAlarmLinkRxMisConnect (5)

•imaAlarmLinkTxFault (6)

•imaAlarmLinkRxFault (7)

•imaAlarmLinkTxUnusableFe (8)

•imaAlarmLinkRxUnusableFe (9)

•imaAlarmGroupStartupFe (10)

•imaAlarmGroupCfgAbort (11)

•imaAlarmGroupCfgAbortFe (12)

•imaAlarmGroupInsuffLinks (13)

•imaAlarmGroupInsuffLinksFe (14)

•imaAlarmGroupBlockedFe (15)

•imaAlarmGroupTimingSynch (16)

Syntax

dspimagrpalms

Syntax Description

No parameters

Related Commands

dspimagrpalm

Attributes

Log: no

State: active

Privilege: ANYUSER

Example

Display alarms for all IMA groups:

MGX8850.2.AXSME.a > dspimagrpalms

Group  Number                 : 2.1

Alarm  State                  : Clear

Group  Number                 : 2.2

Alarm  State                  : StartUp Ne

MGX8850.2.AXSME.a >

dspimagrpalmcnt

Display IMA Group Alarm Count—AXSM-32-T1E1-E

Displays the current alarm count for the specified IMA group.

Syntax

dspimagrpalmcnt <group>

Syntax Description

group

The bay (1 or 2) and the IMA group number (1-16) in the format bay.group. For example: 1.16

Related Commands

clrimagrpalmcnt, clrimagrpalmcnts, clrimagrpcnts, clrimalnkcnts, dspimagrpalmcnt, dspimagrpbucketcnt, dspimalnkbucketcnt

Attributes

Log: no

State: active, standby

Privilege: ANYUSER

Example

MGX8850.11.AXSME.a > dspimagrpalmcnt 1.1

  Group Number                     : 1.1

  Group Running Secs               : 0

  Group Unavail Secs               : 0

  Group Num NE Failure             : 0

  Group Num FE Failure             : 0

  Group Avail Cell Rate            : 0

dspimagrpbucketcnt

Display IMA Group Bucket Count—AXSM-32-T1E1-E

Displays the cell count in the policing bucket for the specified IMA group at the specified interval (intvl).

Syntax

dspimagrpbucketcnt <group> <intvl>

Syntax Description

group	The bay (1 or 2) and the IMA group number (1-16) in the format bay.group. For example: 1.16
intvl	The time interval to display (0-96). 0 is the current 15-minute interval. 1 is the most recent 15-minute interval. 2 is the next most recent 15-minute interval, and so on. 96 being the oldest 15-minute interval.

Related Commands

clrimagrpalmcnt, clrimagrpalmcnts, clrimagrpcnts, clrimalnkcnts, dspimagrpalmcnt, dspimalnkbucketcnt

Attributes

Log: no

State: active, standby

Privilege: ANYUSER

Example

MGX8850.6.AXSME.a > dspimagrpbucketcnt 2.1 1

  Group Number              : 2.1       

  Interval Number           : 1         

  Unavailable Seconds       :          0

  Near End Failures         :          0

  Far End Failures          :          0

dspimagrpcnt

Display IMA Group Counters—AXSM-32-T1E1-E

Displays the following performance and statistic counter information for the specified IMA group:

Syntax

dspimagrpcnt <group>

Syntax Description

group

The bay number (1-2) and the IMA group number (1-16) in the format bay.group. For example: 1.16

Related Commands

clrimagrpcnts

Attributes

Log: no

State: active

Privilege: ANYUSER

Example

MGX8850.6.AXSME.a > dspimagrpcnt 2.1 1

Ima Group         : 2.1

Interval          : 1

                            Ingress           Egress

CLP0 Cells                 : 0                  0

CLP1 Cells                 : 0                  0

Valid OAM Cells            : 0                  0

Err OAM Cells              : 0                  0

Rcv Valid RM Cells         : 0                  0

Invalid VPI/VCI/PTI Cells  : 0

Rcv Idle Cells             : 0

Non-zero GFC Cells         : 0

Last Unknown VPI           : 506

Last Unknown VCI           : 47833

Discard HecErr Cells       : 0

Corrected HecErr Cells     : 0

dspimalnk

Display IMA Link—AXSM-32-T1E1-E

Displays the following configuration information for the specified IMA link (bay.link).

Field	Description
IMA Link Number	The bay and link number in the format bay.link.
IMA Link Group Number	The link and group number in the format link.group.
LinkRelDelay	The latest measured delay (in milliseconds) on this link relative to the link, in the same IMA group, with the least delay.
LinkNeTxState	The current state of the near-end transmit link
LinkNeRxState	The current state of the near-end receive link.
LinkFeTxState	The current state of the far-end transmit link as reported via ICP cells.
LinkFeRxState	The current state of the far-end receive link as reported via ICP cells.
LinkNeRxFailureStatus	The current link failure status of the near-end receive link.
LinkFeRxFailureStatus	The current link failure status of the far-end receive link as reported via ICP cells.
ImaLink TxLid	The outgoing LID used currently on the link by the local end. This value has meaning only if the link belongs to an IMA group.
ImaLink RxLid	The incoming LID used currently on the link by the remote end as reported via ICP cells. This value has meaning only if the link belongs to an IMA group.
LinkRxTestPattern	This object identifies the test pattern received in the ICP Cell (octet 17) on the link during the IMA Test Pattern Procedure. This value may then be compared to the transmitted test pattern.
LinkTestProcStatus	This value indicates the current state of the Test Pattern Procedure: •disabled: the test is not running •operating: the test is running and no error has been found on this interface. •linkFail: an error has been detected on this link during the test.
LinkLifIntUpTime	LIF integration up time. Range: 0-400000 milliseconds. The LIF (Loss of IMA Frame) defect is the occurrence of persistent OIF (Out of IMA Frame) anomalies for at least 2 IMA frames.
LinkLifIntDnTime	LIF integration down time. Range: 0-400000 milliseconds. The LIF (Loss of IMA Frame) defect is the occurrence of persistent OIF (Out of IMA Frame) anomalies for at least 2 IMA frames.
LinkLodsIntUpTime	LODS integration up time. Range 0-100000 milliseconds. The LODS (Link Out of Delay Synchronization) is a link event indicating that the link is not synchronized with the other links within the IMA group.
LinkLodsIntDnTime	LODS integration down time. Range 0-100000 milliseconds. The LODS (Link Out of Delay Synchronization) is a link event indicating that the link is not synchronized with the other links within the IMA group.

Syntax

dspimalnk <link>

Syntax Description

link	The bay number (1-2) and the IMA link number (1-16) in the format bay.link. For example: 1.16

Related Commands

addimalnk, delimalnk

Attributes

Log: no

State: active

Privilege: ANYUSER

Example

Display the configuration information for IMA link number 2 on bay 9.

MGX8850.6.AXSME.a > dspimalnk 2.9 

IMA Link Number : 2.9 

IMA Link Group Number : 2.1 

LinkRelDelay (msec) : 0 

LinkNeTxState : Unusable-Failed 

LinkNeRxState : Not In Grp 

LinkFeTxState : Not In Grp 

LinkFeRxState : Not In Grp 

LinkNeRxFailureStatus : Lif Fail 

LinkFeRxFailureStatus : No Failure 

ImaLink TxLid : 8 

ImaLink RxLid : 255 

LinkRxTestPattern : 255 

LinkTestProcStatus : Disabled 

LinkLifIntUpTime : 2500 

LinkLifIntDnTime : 10000 

LinkLodsIntUpTime : 2500 

LinkLodsIntDnTime : 10000

dspimalnks

Display IMA Links—AXSM-32-T1E1-E

Displays the following configuration information for IMA links.

Information	Description
imaLinkIfIndex	This corresponds to the ifIndex of the MIB-II interface on which this link is established. This object also corresponds to the logical number (ifIndex) assigned to this IMA link.
imaLinkGroupIndex	The value which identifies the IMA group (imaGroupIndex) of which this link is a member.
imaLinkRelDelay	The latest measured delay on this link relative to the link, in the same IMA group, with the least delay.
imaLinkNeTxState	The current state of the near-end transmit link
imaLinkNeRxState	The current state of the near-end receive link.
imaLinkNeRxFailureStatus	The current link failure status of the near-end receive link.
imaLinkTxLid	The outgoing LID used currently on the link by the local end. This value has meaning only if the link belongs to an IMA group.
imaLinkRxLid	The incoming LID used currently on the link by the remote end as reported via ICP cells. This value has meaning only if the link belongs to an IMA group.

Syntax

dspimalnks

Syntax Description

No parameters

Related Commands

dspimalnk

Attributes

Log: no

State: active

Privilege: ANYUSER

Example

MGX8850.2.AXSME.a> dspimalnks

Link   Grp   Rel            Ne               Ne               NeRx    Tx   Rx

Num    Num   Dly            Tx               Rx               Fail   Lid  Lid

            (ms)           State            State           Status

------------------------------------------------------------------------------

 2.9   2.1     0            Usable       Not In Grp        Lif Fail    8  255

2.10   2.1     0            Usable       Not In Grp        Lif Fail    9  255

2.11   2.1     0            Active           Active      No Failure   10   10

2.12   2.1     0   Unusable-Failed  Unusable-Failed        Lif Fail   11   11

2.13   2.2     0   Unusable-Failed       Not In Grp        Lif Fail   12  255

2.14   2.2     0   Unusable-Failed       Not In Grp        Lif Fail   13  255

2.15   2.2     0   Unusable-Failed       Not In Grp        Lif Fail   14  255

2.16   2.2     0   Unusable-Failed       Not In Grp        Lif Fail   15  255

MGX8850.13.AXSME.a > 

dspimalnkalm

Display IMA Link Alarm—AXSM-32-T1E1-E

Displays the alarm state of the specified IMA link (bay.link).

Information	Description
imaLinkNumber	The IMA link number
Alarm	The IMA link alarm state
imaLinkNeRxFailureStatus	The IMA link alarm type

Syntax

dspimalnkalm <link>

Syntax Description

link	The bay number (1-2) and the IMA link number (1-16) in the format bay.link. For example: 1.16

Related Commands

dspimalnkalms

Attributes

Log: no

State: active

Privilege: ANYUSER

Example

Display the alarms for bay 1, link 16.

MGX8850.13.AXSME.a > dspimalnkalm 2.9

Link  Number           : 2.9

Alarm State            : Lif Fail

MGX8850.13.AXSME.a > 

dspimalnkalms

Display IMA Link Alarms—AXSM-32-T1E1-E

Displays the alarms states of all IMA links.

Information	Description
imaLinkNumber	The IMA link number
Alarm	The IMA link Alarm State

Syntax

dspimalnkalms

Syntax Description

No parameters

Related Commands

dspimalnkalm

Attributes

Log: no

State: active

Privilege: ANYUSER

Example

Display alarms for all IMA links:

MGX8850.2.AXSME.a > dspimalnkalms

Link  Number           : 2.9

Alarm State            : Lif Fail

Link  Number           : 2.10

Alarm State            : Lif Fail

Link  Number           : 2.11

Alarm State            : Clear

Link  Number           : 2.12

Alarm State            : Lif Fail

Link  Number           : 2.13

Alarm State            : Lif Fail

Link  Number           : 2.14

Alarm State            : Lif Fail

MGX8850.13.AXSME.a > 

dspimalnkbucketcnt

Display IMA Link Bucket Count—AXSM-32-T1E1-E

Displays the cell count in the policing bucket for the specified IMA link at the specified interval (intvl).

Syntax

dspimalnkbucketcnt <link> <intvl>

Syntax Description

link	The bay number (1-2) and the IMA link number (1-16) in the format bay.link. For example: 1.16
intvl	The time interval to display (0-96). 0 is the current 15-minute interval. 1 is the most recent 15-minute interval. 2 is the next most recent 15-minute interval, and so on. 96 being the oldest 15-minute interval.

Related Commands

clrimagrpalmcnt, clrimagrpalmcnts, clrimagrpcnts, clrimalnkcnts, dspimagrpalmcnt, dspimagrpbucketcnt

Attributes

Log: no

State: active, standby

Privilege: ANYUSER

Example

MGX8850.6.AXSME.a > dspimalnkbucketcnt 2.1 1

  Link Number               : 2.1       

  Interval Number           : 1         

                              Near End           Far End

  SESs                      : 0                  0

  Unavailable Seconds       : 900                900

  Tx Unusable Seconds       : 900                900

  Rx Unusable Seconds       : 900                900

  Tx Stuffs                 : 1592           

  Rx Stuffs                 : 0              

  IMA Violations            : 0              

  OIF Anomalies             : 0 

dspimalnkcnt

Display IMA Link Counters—AXSM-32-T1E1-E

Displays the following performance and statistic counter information for an IMA link (bay.link).

Information	Description
IMA Link Number	The number that identifies the IMA link (imaLinkIndex).
IMA Group Number	The number that identifies the IMA group (imaGroupIndex).
IMA Link Violations	The count of errored, invalid, or missing ICP cells, except during SES-IMA or UAS-IMA conditions.
IMA Link OIF Anomalies	The number of OIF anomalies, except during SES-IMA or UAS-IMA conditions, at the near-end. This is an optional attribute.
IMA Link NE SES	The count of one-second intervals containing less than 30 percent of the ICP cells counted as IV-IMAs, or one or more link defects (such as LOS, OOF/LOF, AIS, LIF, LODS, or LCD) except during UAS-IMA condition.
IMA Link FE SES	The count of one-second intervals containing one or more RDI-IMA defects, except during UAS-IMA-FE condition.
IMA Link NE UnavSec	The count of unavailable seconds at the near-end: unavailability begins at the onset of 10 contiguous SES-IMA and ends at the onset of 10 contiguous seconds with no SES-IMA.
IMA Link FE UnavSec	The count of unavailable seconds at the far-end: unavailability begins at the onset of 10 contiguous SES-IMA-FE and ends at the onset of 10 contiguous seconds with no SES-IMA-FE.
IMA Link NE Tx UnusSec	The count of unusable seconds for transmitting at the near-end Tx LSM.
IMA Link NE Rx UnusSec	The count of unusable seconds for receiving at the near-end Rx LSM.
IMA Link FE Tx UnusSec	The count of seconds with unusable indications for transmitting from the far-end Tx LSM.
IMA Link FE Rx UnusSec	The count of seconds with unusable indications for receiving from the far-end Rx LSM.
IMA Link NE Tx Num Fail	The number of times a near-end transmit failure alarm condition has been entered on this link.
IMA Link NE Rx Num Fail	The number of times a near-end receive failure alarm condition has been entered on this link.
IMA Link FE Tx Num Fail	The number of times a far-end transmit failure alarm condition has been entered on this link.
IMA Link FE Rx Num Fail	The number of times a far-end receive failure alarm condition has been entered on this link.
IMA Link Tx Stuffs	The count of stuffed events inserted in the transmit direction. This is an optional attribute.
IMA Link Rx Stuffs	The count of stuffed events detected in the receive direction. This is an optional attribute.
IMA Link Rx Error Free ICP Cells	The count of ICP cells received with no errors.

Syntax

dspimalnkcnt <link>

Syntax Description

link	The bay number (1-2) and the IMA link number (1-16) in the format bay.link. For example: 1.16

Related Commands

dspimalnk

Attributes

Log: no

State: active

Privilege: ANYUSER

Example

MGX8850.2.AXSME.a > dspimalnkcnt 1.2

   IMA Link Number                  : 1.2

   IMA Group Number                 : 1.2

   IMA Link Violations              : 0

   IMA Link OIF Anomalies           : 0

   IMA Link NE SES                  : 0

   IMA Link FE SES                  : 0

   IMA Link NE UnavSec              : 0

   IMA Link FE UnavSec              : 0

   IMA Link NE Tx UnusSec           : 0

   IMA Link NE Rx UnusSec           : 0

   IMA Link FE Tx UnusSec           : 0

   IMA Link FE Rx UnusSec           : 0

   IMA Link NE Tx Num Fail          : 0

   IMA Link NE Rx Num Fail          : 0

   IMA Link FE Tx Num Fail          : 0

   IMA Link FE Rx Num Fail          : 0

   IMA Link Tx Stuffs               : 2059

   IMA Link Rx Stuffs               : 2059

   IMA Link Rx Error Free ICP cells : 0

dspingbucketcnt

Display Ping Bucket Counters—AXSM-E, AXSM-32-T1E1-E, AXSM-XG

Displays selected statistical counters for the specified 15-minute interval (intvl) for all the lines on card.

Syntax

dspingbucketcnt <intvl>

Syntax Description

intvl

The time interval to display (0-96). 0 is the current 15-minute interval. 1 is the most recent 15-minute interval. 2 is the next most recent 15-minute interval, and so on. 96 is the oldest 15-minute interval.

Related Commands

dspegrbucketcnt

Attributes

Log: nolog

State: active, standby

Privilege: ANYUSER

Example

MGX8850.1.10.AXSME.a > dspingbucketcnt 

Line        Total Cells     Total Cells

               Received       Discarded

------- --------------- ---------------

1.1                   0               0

1.2                   0               0

1.3                   0               0

1.4                   0               0

1.5                   0               0

1.6                   0               0

1.7                   0               0

1.8                   0               0

2.1                   0               0

2.2                   0               0

2.3                   0               0

2.4                   0               0

dsplmi

Display Local Management Interface—AXSM

The dsplmi command lets you display details about an extended LMI on an AXSM logical interface. See also description of the addlmi command. Each LMI can support one of the following items:

•A feeder (Cisco MGX 8850 PXM1-based switch)

•A Service Expansion Shelf (SES)

Syntax

dsplmi <ifNum>

Syntax Description

ifNum

The logical interface number has a range of 1-60.

Related Command

dellmi, uplmi, dnlmi, uplmi, clrlmistat, addlmi, dsplmis, dsplmistat

Attributes

Log: yes

State: active

Privilege: ANYUSER

Example

Display the LMI on AXSM port 2.

MGX8850.1.AXSM.a > dsplmi 2

  LMI Interface Number        : 2

  LMI Remote Name             : MGX8850

  LMI IP Address              : 10.10.10.56

  LMI Remote Shelf            : 1

  LMI Remote Slot             : 1

  LMI Remote Port             : 1

  LMI Type                    : AXSM

  LMI Model Number            : 8850

  LMI Configuration           : Up

  LMI Link Status             : Up

LMI Alarms : Clear

dsplmis

Display Local Management Interfaces—AXSM

The dsplmis command lets you display general information about all extended LMIs (XLMIs) on an AXSM card. See also description of the addlmi command. Each LMI can support one of the following items:

•A feeder (Cisco MGX 8850 PXM1-based switch)

•A Service Expansion Shelf (SES)

Syntax

dsplmis

Syntax Description

No parameters

Related Command

dellmi, uplmi, dnlmi, uplmi, clrlmistat, addlmi, dsplmi, dsplmistat

Attributes

Log: yes

State: active

Privilege: ANYUSER

Example

Display all LMIs on the current AXSM. The display shows that only one LMI exists.

MGX8850.1.AXSM.a > dsplmis

 IF     Remote    Remote         Rmt      Rmt      LMI     LMI    LMI 

 No.    Name      IP             Slot     Port     Admin   Oper   Alarms

 ---    -------   ------------   -----    -----    -----   ----   ------

   2 MGX8850    10.10.10.56      1        1        Up       Up     Clear

dsplmistat

Display Local Management Interface Statistics—AXSM

The dsplmistat command lets you display general statistics about an LMIs (XLMIs) on an AXSM interface. See also description of the addlmi command.

Syntax

dsplmistat <ifNum>

Syntax Description

ifNum

The logical interface number has a range of 1-60.

Related Command

dellmi, uplmi, dnlmi, uplmi, clrlmistat, addlmi, dsplmi, dsplmis

Attributes

Log: yes

State: active, standby

Privilege: ANYUSER

Example

Display LMI statistics on AXSM port 2.

MGX8850.1.AXSM.a > dsplmistat 2

STATUS REPORT ENQUIRY transmitted : 1 

STATUS REPORT ENQUIRY received    : 1 

STATUS REPORT transmitted         : 1 

STATUS REPORT received            : 1 

UPDATE STATUS transmitted         : 0 

UPDATE STATUS received            : 0 

UPDATE STATUS ACK transmitted     : 0 

UPDATE STATUS ACK received        : 0 

Invalid PDU received              : 0 

Invalid PDU length received       : 0 

Invalid PDU IEs received          : 0 

Invalid Transaction Num received  : 0 

Unknown PDU type received         : 0 

NODE STATUS enquiry transmitted   : 2748 

NODE STATUS enquiry received      : 2748 

NODE STATUS ack transmitted       : 2748 

NODE STATUS ack received          : 2748 

NODE STATUS degrade transmitted   : 0 

NODE STATUS degrade received      : 0 

NODE STATUS delete transmitted    : 0 

NODE STATUS delete received       : 0 

NODE STATUS unknown received      : 0 

MGX8850.1.AXSM.a >

dspln

Display Line—AXSM, AXSM-E, AXSM-XG

Display the characteristics of a physical line on an AXSM, AXSM-E, or AXSM-XG.

---

Note The alarm status for standby cards is reported as N/A because the alarm status of the standby card may not be the same as the active card.

---

Syntax (AXSM, AXSM-XG)

dspln <-ds3 | -sonet> <bay.line>

Syntax Description (AXSM, AXSM-XG)

bay.line

Identifies the bay (1 or 2) and the line number. The line number is from 1 to the highest numbered line on the back card.

Syntax (AXSM-E, AXSM-XG)

dspln <-ds3|-e3|-sonet|-ds1|-e1> <bay.line>

(AXSM-E, AXSM-XG)

bay.line

Identifies the bay (1 or 2) and the line number. The line number is from 1 to the highest numbered line on the back card.

Related Commands

upln, cnfln

Attributes

Log: no

State: active, standby

Privilege: ANYUSER

Example

Display T3 line 1 on the current AXSM.

MGX8850.11.AXSM.a > dspln -ds3 1.1

  Line Number         : 1.1

  Admin Status        : Down              Alarm Status        : Clear

  Line Type           : ds3cbitadm        Number of ports     : 0

  Line Coding         : ds3B3ZS           Number of partitions: 0

  Line Length(meters) : 0                 Number of SPVC      : 0

  OOFCriteria         : 3Of8Bits          Number of SPVP      : 0

  AIS c-Bits Check    : Check             Number of SVC       : 0

  Loopback            : NoLoop

  Xmt. Clock source   : localTiming

  Rcv FEAC Validation : 4 out of 5 FEAC codes

Display OC-48 line on the current OC-12 AXSM.

MGX8850.1.AXSM.a > dspln -sonet 2.1

  Line Number            : 2.1

  Admin Status           : Up                Alarm Status        : Clear

  Loopback               : NoLoop            APS enabled         : Disable

  Frame Scrambling       : Enable            Number of ports     : 1

  Xmt Clock source       : localTiming       Number of partitions: 1

  Line Type              : sonetSts12c       Number of SPVC      : 0

  Medium Type(SONET/SDH) : SONET             Number of SVC       : 4

  Medium Time Elapsed    : 506223

  Medium Valid Intervals : 96

  Medium Line Type       : ShortSMF 

Display DS3 line 1 on the current AXSM-E.

MGX8850.5.AXSME.a > dspln -ds3 1.1 

  Line Number         : 1.1

  Admin Status        : Up                Alarm Status        : Critical

  Line Type           : ds3cbitadm        Number of ports     : 1

  Line Coding         : ds3B3ZS           Number of partitions: 1

  Line Length(meters) : 0                 Number of SPVC      : 0

  OOFCriteria         : 3Of16Bits         Number of SPVP      : 0

  AIS c-Bits Check    : Check             Number of SVC       : 0

  Loopback            : NoLoop

  Xmt. Clock source   : localTiming

  Rcv FEAC Validation : 8 out of 10 FEAC codes

Display SONET line 1 on the current AXSM-E.

MGX8850.11.AXSME.a > dspln -sonet 1.1

  Line Number            : 1.1

  Admin Status           : Up                Alarm Status        : Critical

  Loopback               : NoLoop            APS enabled         : Disable

  Frame Scrambling       : Enable            Number of ports     : 1

  Xmt Clock source       : localTiming       Number of partitions: 1

  Line Type              : sonetSts3c        Number of SPVC      : 2

  Medium Type(SONET/SDH) : SONET             Number of SPVP      : 0

  Medium Time Elapsed    : 488               Number of SVC       : 0

  Medium Valid Intervals : 96

  Medium Line Type       : Other

Display DS1 line 1 on the current AXSM-E.

MGX8850.9.AXSME.a > dspln -ds1 1.1

Line Number         : 1.1

  Admin Status        : Up                Alarm Status        : Clear

  Line Type           : dsx1ESF           Number of ports     : 0

  Line Coding         : dsx1B8ZS          Number of partitions: 0

  Line Length(meters) : 40                Number of SPVC      : 0

  Loopback            : NoLoop            Number of SPVP      : 0

  Xmt. Clock source   : localTiming       Number of SVC       : 0

  Valid Intervals     : 7

  Circuit Identifier  : line 1.1, slot 10, Node 222, Rack 21, SJ-3-3-1, Cisco Sys. Inc.