Contents
Configuring Quality of Service
This chapter includes the following sections:
- Quality of Service
- System Classes
- Quality of Service Policies
- Flow Control Policies
- Configuring a System Class
- Disabling a System Class
- Configuring a QoS Policy
- Deleting a QoS Policy
- Configuring a Flow Control Policy
- Deleting a Flow Control Policy
System Classes
Cisco UCS uses Data Center Ethernet (DCE) to handle all traffic inside a Cisco UCS instance. This industry standard enhancement to Ethernet divides the bandwidth of the Ethernet pipe into eight virtual lanes. System classes determine how the DCE bandwidth in these virtual lanes is allocated across the entire Cisco UCS instance.
Each system class reserves a specific segment of the bandwidth for a specific type of traffic. This provides a level of traffic management, even in an oversubscribed system. For example, you can configure the Fibre Channel Priority system class to determine the percentage of DCE bandwidth allocated to FCoE traffic.
The following table describes the system classes:
System Class
Description
Platinum Priority
Gold Priority
Silver Priority
Bronze Priority
A configurable set of system classes that you can include in the QoS policy for a service profile. Each system class manages one lane of traffic.
All properties of these system classes are available for you to assign custom settings and policies.
Best Effort Priority
A system class that sets the quality of service for the lane reserved for Basic Ethernet traffic.
Some properties of this system class are preset and cannot be modified. For example, this class has a drop policy that allows it to drop data packets if required.
Fibre Channel Priority
A system class that sets the quality of service for the lane reserved for Fibre Channel over Ethernet traffic.
Some properties of this system class are preset and cannot be modified. For example, this class has a no-drop policy that ensures it never drops data packets.
Quality of Service Policies
QoS policies assign a system class to the outgoing traffic for a vNIC or vHBA. This system class determines the quality of service for that traffic.
You must include a QoS policy in a vNIC policy or vHBA policy and then include that policy in a service profile to configure the vNIC or vHBA.
Flow Control Policies
Flow control policies determine whether the uplink Ethernet ports in a Cisco UCS instance send and receive IEEE 802.3x pause frames when the receive buffer for a port fills. These pause frames request that the transmitting port stop sending data for a few milliseconds until the buffer clears.
For flow control to work between a LAN port and an uplink Ethernet port, you must enable the corresponding receive and send flow control parameters for both ports. For Cisco UCS, the flow control policies configure these parameters.
When you enable the send function, the uplink Ethernet port sends a pause request to the network port if the incoming packet rate becomes too high. The pause remains in effect for a few milliseconds before traffic is reset to normal levels. If you enable the receive function, the uplink Ethernet port honors all pause requests from the network port. All traffic is halted on that uplink port until the network port cancels the pause request.
Because you assign the flow control policy to the port, changes to the policy have an immediate effect on how the port reacts to a pause frame or a full receive buffer.
Configuring a System Class
ProcedureThe following example enables the platinum system class, allows the channel to drop packets, sets the class of service to 6, sets the MTU to normal, optimizes the class for sending multicast packets, sets the relative weight to 5, and commits the transaction:
UCS-A# scope eth-server UCS-A /eth-server # scope qos UCS-A /eth-server/qos # scope eth-classified platinum UCS-A /eth-server/qos/eth-classified # enable UCS-A /eth-server/qos/eth-classified* # set drop drop UCS-A /eth-server/qos/eth-classified* # set cos 6 UCS-A /eth-server/qos/eth-classified* # set mtu normal UCS-A /eth-server/qos/eth-classified* # set multicast-optimize yes UCS-A /eth-server/qos/eth-classified* # set weight 5 UCS-A /eth-server/qos/eth-classified* # commit-buffer UCS-A /eth-server/qos/eth-classified #Disabling a System Class
Procedure
Command or Action Purpose Step 1 UCS-A# scope eth-server Enters Ethernet server mode.
Step 2 UCS-A /eth-server # scope qos Enters Ethernet server QoS mode.
Step 3 UCS-A /eth-server/qos # scope eth-classified {bronze | gold | platinum silver} Enters Ethernet server QoS Ethernet classified mode for the specified system class.
Step 4 UCS-A /eth-server/qos/eth-classified # disable Disables the specified system class.
Step 5 UCS-A /eth-server/qos/eth-classified # commit-buffer Commits the transaction to the system configuration.
The following example disables the platinum system class and commits the transaction:
UCS-A# scope eth-server UCS-A /eth-server # scope qos UCS-A /eth-server/qos # scope eth-classified platinum UCS-A /eth-server/qos/eth-classified # disable UCS-A /eth-server/qos/eth-classified* # commit-buffer UCS-A /eth-server/qos/eth-classified #Configuring a QoS Policy
Procedure
Command or Action Purpose Step 1 UCS-A# scope org org-name Enters organization mode for the specified organization. To enter the root organization mode, type / as the org-name.
Step 2 UCS-A /org # create qos-policy policy-name Creates a QoS policy with the specified policy name, and enters organization QoS policy mode.
Step 3 UCS-A /org/qos-policy # create vnic-egress-policy Creates a vNIC egress policy to be used for the QoS policy and enters organization QoS policy vNIC egress policy mode.
Step 4 UCS-A /org/qos-policy/vnic-egress-policy # set prio {best-effort | bronze | gold | platinum | silver} Specifies the name of the system class to be used for the vNIC egress policy.
Step 5 UCS-A /org/qos-policy/vnic-egress-policy # commit-buffer Commits the transaction to the system configuration.
What to Do NextThe following example assigns the best effort system class to the vNIC egress policy of the QoS policy and commits the transaction:
UCS-A# scope org / UCS-A /org # create qos-policy QosPolicy34 UCS-A /org/qos-policy* # create vnic-egress-policy UCS-A /org/qos-policy/vnic-egress-policy* # set prio best-effort UCS-A /org/qos-policy/vnic-egress-policy* # commit-buffer UCS-A /org/qos-policy/vnic-egress-policy #
Include the QoS policy in a vNIC template.
Deleting a QoS Policy
ProcedureIf you delete a QoS policy that is in use or disable a system class that is used in a QoS policy, any vNIC which uses that QoS policy is assigned to the Best Effort Priority system class. In a system that implements multi-tenancy, Cisco UCS Manager first attempts to find a matching QoS policy in the organization hierarchy.
Command or Action Purpose Step 1 UCS-A# scope org org-name Enters organization mode for the specified organization. To enter the root organization mode, type / as the org-name.
Step 2 UCS-A /org # delete qos-policy policy-name Deletes the specified QoS policy.
Step 3 UCS-A /org # commit-buffer Commits the transaction to the system configuration.
Configuring a Flow Control Policy
Before You BeginProcedureConfigure the network port with the corresponding setting for the flow control that you need. For example, if you enable the send setting for flow-control pause frames in the policy, make sure that the receive parameter in the network port is set to on or desired. If you want the Cisco UCS port to receive flow-control frames, make sure that the network port has a send parameter set to on or desired. If you do not want to use flow control, you can set the send and receive parameters on the network port to off.
Command or Action Purpose Step 1 UCS-A# scope eth-uplink Enters Ethernet uplink mode.
Step 2 UCS-A /eth-uplink # scope flow-control Enters Ethernet uplink flow control mode.
Step 3 UCS-A /eth-uplink/flow-control # create policy policy-name Creates the specified flow control policy.
Step 4 UCS-A /eth-uplink/flow-control/policy # set prio prio-option Specifies one of the following flow control priority options:
Step 5 UCS-A /eth-uplink/flow-control/policy # set receive receive-option Specifies one of the following flow control receive options:
Step 6 UCS-A /eth-uplink/flow-control/policy # set send send-option Specifies one of the following flow control send options:
Step 7 UCS-A /org/qos-policy/vnic-egress-policy # commit-buffer Commits the transaction to the system configuration.
What to Do NextThe following configures a flow control policy and commits the transaction:
UCS-A# scope eth-uplink UCS-A /eth-uplink* # scope flow-control UCS-A /eth-uplink/flow-control* # create policy FlowControlPolicy23 UCS-A /eth-uplink/flow-control/policy* # set prio auto UCS-A /eth-uplink/flow-control/policy* # set receive on UCS-A /eth-uplink/flow-control/policy* # set send on UCS-A /eth-uplink/flow-control/policy* # commit-buffer UCS-A /eth-uplink/flow-control/policy #
Associate the flow control policy with an uplink Ethernet port or port channel.
Deleting a Flow Control Policy
Procedure
Command or Action Purpose Step 1 UCS-A# scope eth-uplink Enters Ethernet uplink mode.
Step 2 UCS-A /eth-uplink # scope flow-control Enters Ethernet uplink flow control mode.
Step 3 UCS-A /eth-uplink/flow-control # delete policy policy-name Deletes the specified flow control policy.
Step 4 UCS-A /eth-uplink/flow-control # commit-buffer Commits the transaction to the system configuration.
The following example deletes the flow control policy named FlowControlPolicy23 and commits the transaction:
UCS-A# scope eth-uplink UCS-A /eth-uplink* # scope flow-control UCS-A /eth-uplink/flow-control* # delete policy FlowControlPolicy23 UCS-A /eth-uplink/flow-control* # commit-buffer UCS-A /eth-uplink/flow-control #