Table Of Contents

Using Reports

Using the Device Center

Viewing the Fault Summary Report

Viewing Device History

Viewing Config History

Viewing Firmware History

Displaying Wireless Client Reports

Displaying a Client Detail Report

Displaying a Client Statistics Report

Displaying a Client Historical Association Report

Displaying Current Reports

Displaying a Group Report

Displaying a Group Security Report

Displaying a Group SSID Report

Displaying a Group VLAN Report

Displaying a Per VLAN Client Report

Displaying a Group Policy Report

Displaying an AP Summary Report

Displaying a Detailed Report

Displaying a Current Client Association Report

Displaying an EAP Authentication Report

Displaying an AP Ethertype Protocol Filters Report

Displaying an AP IP Protocol Filters Report

Displaying an AP IP Port Filters Report

Displaying an AP Policy Report

Displaying an AP QBSS QoS Report

Displaying an AP SSID Report

Displaying an AP VLAN Report

Displaying a Per VLAN Client Report

Displaying a Switch Summary Report

Displaying an AP and Bridge Connected to Switch Report

Displaying a Router Summary Report

Displaying an AP and Bridge Connected to Router Report

Displaying a Server Summary Report

Displaying Trends

Displaying a Group Performance Report: RF Utilization

Displaying a Group Performance Report: Ethernet Utilization

Displaying a Top N Number of Associations Report

Displaying a Top N Percentage Errors

Displaying an AP and Bridge RF Transmission Statistics Report

Displaying an AP and Bridge Ethernet Transmission Statistics Report

Displaying an AP and Bridge Performance Graph

Displaying an AP and Bridge Performance: Tabular

Displaying Top N Busiest Clients

Displaying Top N Client Error Rate

Displaying a Server Response Time Graph

Exporting a Report

Emailing a Report

Scheduling Email Jobs

Viewing Email Job Details

Using Reports

---

The Reports tab displays information about your devices. You can save and email reports. You can also set specific times for emailed reports to be run and sent automatically.

The reports available are dependent on the groups of devices and individual devices you choose from the selector in the left pane.

Following are the subtabs under Reports:

---

Note Some of the subtabs may not be visible to some users.

---

•Device Center—See Using the Device Center

•Wireless Clients—See Displaying Wireless Client Reports

•Current—See Displaying Current Reports

•Trends—See Displaying Trends

•Scheduled Email Jobs—See Scheduling Email Jobs

Using the Device Center

The device center enables you to quickly access various types of reports for a particular device.

---

Note Your login determines whether you can use this option.

---

Procedure

---

Step 1 Select Reports > Device Center. The Device Center appears above the device selector in the left pane.

Step 2 If you want to search for the device, use the dialog box in the left pane above the device selector:

a. From the list, select the method you want to use to search for the device: by name or by IP address.

b. Enter the IP address or name, or use an asterisk (*) as a wildcard to denote numbers and letters, then click Search. The requested device appears in the Search Results folder.

Step 3 Select the device from the folder in the left pane, and the right pane displays the Summary Report for the device.

Step 4 Click on the buttons for different report types:

•For access points and bridges:

–Summary report—See Displaying an AP Summary Report

–Detailed report—See Displaying a Detailed Report

–Fault Status—See Viewing the Fault Summary Report

–Device History—See Viewing Device History

–Config History—See Viewing Config History

–Firmware History—See Viewing Firmware History

–AP Web Page—Opens up a browser window to the AP Summary Status.

•For switches:

–Summary report —SeeDisplaying a Switch Summary Report

–Fault Status—See Viewing the Fault Summary Report

–Device History—See Viewing Device History

•For routers:

–Summary Report—See Displaying a Router Summary Report

–Fault Status—See Viewing the Fault Summary Report

–Device History—See Viewing Device History

•For servers—See Displaying a Server Response Time Graph.

Viewing the Fault Summary Report

The following table is displayed for the device's fault summary:

Table 5-1 Device Fault Summary 

Column	Description
Type	The fault type.
Description	A description of the fault. Click to see fault details. See Viewing Fault Details.
Severity	The fault severity level.
State	The current state of the fault.
Timestamp	The time the fault was reported. Click to see fault details. See Viewing Fault Details. For more information, see Time Display.

To sort table data, click on the column heading by which you want to sort the data:

•A triangle indicates ascending order.

•An upside-down triangle indicates descending order.

•No triangle indicates that the data is not sorted.

Viewing Device History

The following table is displayed for the device's history:

Table 5-2 Device History  

Column	Description
Timestamp	The time the device's state last changed. For more information, see Time Display.
Device Name	The name of the device.
IP Address	The IP address of the device.
State	The current state of the device.

To sort table data, click on the column heading by which you want to sort the data:

•A triangle indicates ascending order.

•An upside-down triangle indicates descending order.

•No triangle indicates that the data is not sorted.

Viewing Config History

The following table is displayed for the device's configuration history:

Table 5-3 Device Configuration History  

Column	Description
Start Time	The start time for the device's configuration.
End Time	The end time for the device's configuration.
Job Status	The state of the configuration job.
Template Name	The name of the configuration template used.
Job Protocol	The protocol used for the configuration job.
Job Name	The name of the configuration job.
Job Type	The type of configuration job.

To sort table data, click on the column heading by which you want to sort the data:

•A triangle indicates ascending order.

•An upside-down triangle indicates descending order.

•No triangle indicates that the data is not sorted.

Viewing Firmware History

The following table is displayed for the device's firmware history:

Table 5-4 Device Firmware History  

Column	Description
Start Time	The start time for the device's firmware upgrade job.
End Time	The end time for the device's firmware upgrade job.
Job Status	The state of the firmware job.
Image Name	The name of the firmware image.
Image Version	The version of the firmware.
Image Device Type	The device type.
Job Protocol	The protocol used for the firmware job.
Job Name	The name of the firmware job.

To sort table data, click on the column heading by which you want to sort the data:

•A triangle indicates ascending order.

•An upside-down triangle indicates descending order.

•No triangle indicates that the data is not sorted.

Displaying Wireless Client Reports

Wireless client reports provide information about the type of client that is associating with an access point, information about how much bandwidth the client is using, and a history of which access points the client has been associated with.

Using this window, you can search for a wireless client based on its MAC address or name.

The frequency with which the Wireless Clients reports are updated is 5 minutes by default. To change the default setting, see Managing System Parameters.

---

Note Your login determines whether you can use this option.

---

Following are the report types you can view:

•Client Detail Report—See Displaying a Client Detail Report

•Client Statistics Report—See Displaying a Client Statistics Report

•Client Historical Association Report—See Displaying a Client Historical Association Report

Displaying a Client Detail Report

Procedure

---

Step 1 Select Reports > Wireless Clients. The Wireless Clients selector appears in the left pane.

Step 2 From the list, select the method you want to use to search for clients: by MAC address or name.

Step 3 Enter the MAC address or name. You can use an asterisk (*) as a wildcard to denote numbers and letters.

---

Note The MAC address must be entered in hexadecimal, for example 0070eb37c90.

---

Step 4 Click Search. A list appears in the left pane.

If you chose MAC address in the previous step, MAC addresses are listed; if you chose name, names are listed.

Step 5 Click the MAC address or name. The right pane refreshes and displays the Client Detail Report, which is the default report, with the following information:

Table 5-5 Client Detail Report  

Column	Description
Name	The name assigned to the wireless client device.
IP Address	The IP address of the wireless client device.
Classification	The type of wireless client device.
Associated with	The name or IP of the access point with which it was last associated.
State	The operational state of the wireless client device.
Time last seen	The time the client was last seen by the system.
Software Version	The version of wireless client software.
MAC Address	The MAC address of the wireless client.

Step 6 To export the report, click Export. (See Exporting a Report.)

Step 7 To email the report, click Email Report. (See Emailing a Report.)

---

Displaying a Client Statistics Report

Procedure

---

Step 1 Select Reports > Wireless Clients. The Wireless Clients selector appears in the left pane.

Step 2 From the list, select the method you want to use to search for clients: by MAC address or name.

Step 3 Enter the MAC address or name. You can use an asterisk (*) as a wildcard to denote numbers and letters.

Step 4 Click Search. A list appears in the left pane.

Step 5 Select the MAC address or name. The right pane refreshes.

Step 6 From the Report Name list, select Client Statistics Report.

Step 7 Click View. The Client Statistics Report displays in the right pane with the following information:

Table 5-6 Client Statistics Report  

Column	Description
Name	The name of the wireless client.
IP address	The IP address of the wireless client.
Time last seen	The time the wireless client was last seen by the system.
Packets transmitted	The number of packets transmitted.
Octets transmitted	The number of octets transmitted.
Packets received	The number of packets received.
Octets received	The number of octets received.
Latest received signal strength	A tally of the received signal quality.
Latest signal quality	The current index of radio signal quality.
Sleep time in power save mode	The number of beacon intervals across which the station will sleep in power-save mode, or 1 if the station will never be in power-save mode.
Preferred transmission rate	The preferred data transmission rate.
Short retries	The number of times the RTS (request to send) packet had to be retried.
Latest short retries	A tally of the number of retries.
Long retries	The number of times the data packet had to be retried.
Latest long retries	A tally of the number of retries.
Received WEP errors	The number of received encryption errors.
Errors in transmitted packets	The number of errors in transmitted packets.
Errors in received packets	The number of errors in received packets.
Errors in received octets	The number of errors in received octets.
Announcements sent	The total number of announcement packets sent since the device was reset.

Step 8 To export the report, click Export. (See Exporting a Report.)

Step 9 To email the report, click Email Report. (See Emailing a Report.)

---

Displaying a Client Historical Association Report

Procedure

---

Step 1 Select Reports > Wireless Clients. The Wireless Clients selector appears in the left pane.

Step 2 From the list, select the method you want to use to search for clients: by MAC address or name.

Step 3 Enter the MAC address or name. You can use an asterisk (*) as a wildcard to denote numbers and letters.

Step 4 Click Search. A list appears in the left pane.

Step 5 Select the MAC address or name. The right pane refreshes.

Step 6 From the Report Name list, select Client Historical Association Report.

Step 7 Click View. The Client Historical Association Report displays in the right pane with the following information:

Table 5-7 Client Historical Association Report  

Column	Description
Associated with	The name or IP address of the AP. Click on this link to view the AP Summary Report and the Fault Summary. For more information, see Displaying an AP Summary Report.
Client IP Address	The IP address of the wireless client device.
Software Version	The software version of the wireless client device.
Associated Time	The time when the WLSE has polled the access point to retrieve the client association time. Tip To ensure that you are viewing the most up-to-date information, verify when the last inventory cycle occurred. Client inventory status can be seen by selecting Administration > Discover > Tasks History > Inventory.

Step 8 To sort table data, click on the column heading you want to use to sort the data:

•A triangle indicates ascending order.

•An upside-down triangle indicates descending order.

•No triangle indicates that the data is not sorted.

Step 9 To export the report, click Export. (See Exporting a Report.)

Step 10 To email the report, click Email Report. (See Emailing a Report.)

---

Displaying Current Reports

This window allows you to view current information about the monitored devices in your network. You can view, export, and email the reports.

The frequency with which configuration data is collected from the devices is 15 minutes by default. To change the default setting, see Managing System Parameters.

---

Note Your login determines whether you can use this option.

---

Using this option, you can view the following types of current reports:

•Group Reports

•Individual Access Point and Bridge Reports

•Individual Switch Reports

•Individual Router Reports

•Individual Server Reports

Group Reports

•Group Report—See Displaying a Group Report

•Group Security Report—See Displaying a Group Security Report

•Group SSID Report—See Displaying a Group SSID Report

•Group VLAN Report—See Displaying a Group VLAN Report

•Per VLAN Client Report—See Displaying a Per VLAN Client Report

•Group Policy Report—See Displaying a Group Policy Report

Individual Access Point and Bridge Reports

•Summary Report—See Displaying an AP Summary Report

•Detailed Report—See Displaying a Detailed Report

•Current Client Association—See Displaying a Current Client Association Report

•EAP Authentication Report—See Displaying an EAP Authentication Report

•AP Ethertype Protocol Filters—See Displaying an AP Ethertype Protocol Filters Report

•AP IP Protocol Filters—See Displaying an AP IP Protocol Filters Report

•AP IP Port Filters—See Displaying an AP IP Port Filters Report

•AP Policy Report—See Displaying an AP Policy Report

•AP QBSS QoS Report—Displaying an AP QBSS QoS Report

•AP SSID Report—Displaying an AP SSID Report

•AP VLAN Report—Displaying an AP VLAN Report

•Per VLAN Client Report—Displaying a Per VLAN Client Report

Individual Switch Reports

•Switch Summary Report—See Displaying a Switch Summary Report

•AP and Bridge Connected to Switch Report—See Displaying an AP and Bridge Connected to Switch Report

Individual Router Reports

•Router Summary Report—See Displaying a Router Summary Report

•AP and Bridge Connected to Router Report—See Displaying an AP and Bridge Connected to Router Report

Individual Server Reports

•Server Summary Report—See Displaying a Server Summary Report

Displaying a Group Report

This report lists all the currently connected access points and bridges in a given group and the total number of clients connected to them. It shows the last polled values and the overall status for the group.

Procedure

---

Step 1 Select Reports > Current. The window refreshes with a device selector in the left pane.

Step 2 From the device selector in the left pane, click to expand the folder for the group reports you want to view. The right pane refreshes.

Step 3 From the Report Name list, select Group Report.

Step 4 Click View. The group report is displayed with the following headings:

Table 5-8 Group Report  

Column	Description
Number of Clients Associated to this Group	The total number of clients currently associated with the group of access points or bridges.
Count of Active Stations in this Group	The number of access points or bridges currently in the group.
As Of	The time the state of the group last changed. For more information, see Time Display.
AP Name	The name of the access point. Click to view the following: •AP Detailed Report—See Displaying a Detailed Report. •Fault Summary—See Viewing the Fault Summary Report. •EAP Authentication Report—See Displaying an EAP Authentication Report.
AP IP Address	The IP address of the access point. Click to open up a browser window to the AP Summary Status.
Number of Clients Connected	The number of wireless clients connected to the device.
Number of Bridges Connected	The number of bridges connected to the access point.
Number of AP-Repeaters Connected	The number of repeaters connected to the access point.
Status (Fault)	Click to view the Fault Summary. For more information, see Viewing the Fault Summary Report.
As Of	The time the access point's state last changed. For more information, see Time Display.

Step 5 To sort table data, click on the column heading you want to use to sort the data:

•A triangle indicates ascending order.

•An upside-down triangle indicates descending order.

•No triangle indicates that the data is not sorted.

Step 6 To export the report, click Export. (See Exporting a Report.)

Step 7 To email the report, click Email Report. (See Emailing a Report.)

---

Displaying a Group Security Report

Procedure

---

Step 1 Select Reports > Current. The window refreshes with a device selector in the left pane.

Step 2 From the device selector in the left pane, click to expand the folder for the group security reports you want to view.

Step 3 From the Report Name list, select Group Security Report.

Step 4 Click View. The group report is displayed with the following headings:

Table 5-9 Group Security Report  

Column	Description
AP Name	The name of the device. Click to view the following: •AP Detailed Report—Displaying a Detailed Report. •Fault Summary—Viewing the Fault Summary Report. •EAP Authentication Report—Displaying an EAP Authentication Report.
AP IP Address	The IP address of the device. Click to open up a browser window to the AP Summary Status.
RF Interface	The radio frequency interface.
Encryption type	Indicates the type of encryption used: No Encryption, Optional, or Full Encryption.
Length of WEP Key1 through 4 (in bits)	The WEP key length.
Authentication Type - Open System	Indicates whether any device, regardless of its WEP keys, can authenticate and attempt to associate.
Authentication Type - Shared Key	Indicates whether an access point sends a query to any device attempting to associate with the access point.
Status (Fault)	Click to view the Fault Summary. For more information, see Viewing the Fault Summary Report.
Link to EAP Authentication Report	Click to view the EAP Authentication report. For more information, see Displaying an EAP Authentication Report.
As Of	The time the fault was reported. For more information, see Time Display.

Step 5 To sort table data, click on the column heading you want to use to sort the data:

•A triangle indicates ascending order.

•An upside-down triangle indicates descending order.

•No triangle indicates that the data is not sorted.

Step 6 To export the report, click Export. (See Exporting a Report.)

Step 7 To email the report, click Email Report. (See Emailing a Report.)

---

Displaying a Group SSID Report

This report displays all the configured SSIDs (both primary and auxiliary) and their corresponding properties in all the devices in the group.

Procedure

---

Step 1 Select Reports > Current. The window refreshes with a device selector in the left pane. From the device selector in the left pane, click the group folder for which you want to see a report. The right pane refreshes.

Step 2 From the Report Name list, select Group SSID Report.

Step 3 Click View. The following report displays the following:

Table 5-10 Group SSID Report  

Column	Description
SSID	The unique identifier the client device uses to associate with the access point.
VLAN ID	The identification number of the VLAN.
VLAN Name	The name of the VLAN.
AP Name	The name of the access point. Click to view the following: •AP Detailed Report—See Displaying a Detailed Report. •Fault Summary—See Viewing the Fault Summary Report. •EAP Authentication Report—See Displaying an EAP Authentication Report.
AP IP Address	The IP address of the access point. Click to open up a browser window to the AP Summary Status.
Number of Clients Connected	The number of wireless clients connected to the device.
Priority	The priority configuration based on the traffic type.
Default Policy Group	The number of the default policy group (which contains access parameters). Click to view the Policy Report—See Displaying a Group Policy Report.
As Of	The time the access point's state last changed. For more information, see Time Display.

Step 4 To sort table data, click on the column heading you want to use to sort the data:

•A triangle indicates ascending order.

•An upside-down triangle indicates descending order.

•No triangle indicates that the data is not sorted.

Step 5 To export the report, click Export. (See Exporting a Report.)

Step 6 To email the report, click Email Report. (See Emailing a Report.)

---

Displaying a Group VLAN Report

This report displays all the configured VLANs and their corresponding properties in the group.

Procedure

---

Step 1 Select Reports > Current. The window refreshes with a device selector in the left pane. From the device selector in the left pane, click the group folder for which you want to see a report. The right pane refreshes.

Step 2 From the Report Name list, select Group VLAN Report.

Step 3 Click View. The following report displays the following:

Table 5-11 Group VLAN Report  

Column	Description
VLAN ID	The identification number of the VLAN.
VLAN Name	The name of the VLAN.
AP Name	The name of the access point. Click to view the following: •AP Detailed Report—See Displaying a Detailed Report. •Fault Summary—See Viewing the Fault Summary Report. •EAP Authentication Report—See Displaying an EAP Authentication Report.
AP IP Address	The IP address of the access point. Click to open up a browser window to the AP Summary Status.
SSID	The unique identifier the client device uses to associate with the access point.
Number of Clients Connected	The number of wireless clients connected to the device.
Priority	The priority configuration based on the traffic type.
Default Policy Group	The number of the default policy group (which contains access parameters). Click to view the Policy Report—See Displaying a Group Policy Report.
As Of	The time the access point's state last changed. For more information, see Time Display.

Step 4 To sort table data, click on the column heading you want to use to sort the data:

•A triangle indicates ascending order.

•An upside-down triangle indicates descending order.

•No triangle indicates that the data is not sorted.

Step 5 To export the report, click Export. (See Exporting a Report.)

Step 6 To email the report, click Email Report. (See Emailing a Report.)

---

Displaying a Per VLAN Client Report

Procedure

---

Step 1 Select Reports > Current. The window refreshes with a device selector in the left pane. From the device selector in the left pane, click the group folder for which you want to see a report. The right pane refreshes.

Step 2 From the Report Name list, select Per VLAN Client Report.

Step 3 Click View. The following report displays the following:

Table 5-12 Per VLAN Client Report  

Column	Description
VLAN ID	The identification number of the VLAN.
VLAN Name	The name of the VLAN.
AP Name	The name of the access point. Click to view the following: •AP Detailed Report—See Displaying a Detailed Report. •Fault Summary—See Viewing the Fault Summary Report. •EAP Authentication Report—See Displaying an EAP Authentication Report.
Client MAC Address	The MAC address of the client.
Client Name	The name of the client.
Client IP Address	The IP address of the client.
SSID	The unique identifier the client device uses to associate with the access point.
Client Type	The type of client.
As Of	The time the access point's state last changed. For more information, see Time Display.

Step 4 To sort table data, click on the column heading you want to use to sort the data:

•A triangle indicates ascending order.

•An upside-down triangle indicates descending order.

•No triangle indicates that the data is not sorted.

Step 5 To export the report, click Export. (See Exporting a Report.)

Step 6 To email the report, click Email Report. (See Emailing a Report.)

---

Displaying a Group Policy Report

This report lists all the policy groups configured on each of the access points in this group.

Procedure

---

Step 1 Select Reports > Current. The window refreshes with a device selector in the left pane. From the device selector in the left pane, click the group folder for which you want to see a report. The right pane refreshes.

Step 2 From the Report Name list, select Group Policy Report.

Step 3 Click View. The following report displays the following:

Table 5-13 Group Policy Report  

Column	Description
AP Name	The name of the access point. Click to view the following: •AP Detailed Report—See Displaying a Detailed Report. •Fault Summary—See Viewing the Fault Summary Report. •EAP Authentication Report—See Displaying an EAP Authentication Report.
AP IP Address	The IP address of the access point. Click to open up a browser window to the AP Summary Status.
Policy Group Id	The identification number of the policy group.
Policy Group Name	The name of the policy group.
Ethertype Filter Id (In)	The identification number of the (receive) Ethertype filter. Click to view the AP Ethertype Protocol Filters Report—See Displaying an AP Ethertype Protocol Filters Report.
Ethertype Filter Id (Out)	The identification number of the (transmit) Ethertype filter. Click to view the AP Ethertype Protocol Filters Report—See Displaying an AP Ethertype Protocol Filters Report.
IP Protocol Filter Id (In)	The identification number of the (receive) IP protocol filter. Click to view the AP IP Protocol Filters Report—See Displaying an AP IP Protocol Filters Report.
IP Protocol Filter Id (Out)	The identification number of the (transmit) IP protocol filter Click to view the AP IP Protocol Filters Report—See Displaying an AP IP Protocol Filters Report.
IP Port Filter Id (In)	The identification number of the (receive) IP port filter. Click to view the AP IP Port Filters Report—See Displaying an AP IP Port Filters Report.
IP Port Filter Id (Out)	The identification number of the (transmit) IP port filter. Click to view the AP IP Port Filters Report—See Displaying an AP IP Port Filters Report.
As Of	The time the device's state last changed. For more information, see Time Display.

Step 4 To sort table data, click on the column heading you want to use to sort the data:

•A triangle indicates ascending order.

•An upside-down triangle indicates descending order.

•No triangle indicates that the data is not sorted.

Step 5 To export the report, click Export. (See Exporting a Report.)

Step 6 To email the report, click Email Report. (See Emailing a Report.)

---

Displaying an AP Summary Report

Procedure

---

Step 1 Select Reports > Current. The window refreshes with a device selector in the left pane.

Step 2 If you want to search for the device, use the dialog box in the left pane above the device selector:

a. From the list, select the method you want to use to search for the device: by name or by IP address.

b. Enter the IP address or name, or use an asterisk (*) as a wildcard to denote numbers and letters, then click Search. The requested device appears in the Search Results folder.

Step 3 From the device selector in the left pane, click to expand the folder and select the device for which you want a report. The right pane refreshes.

Step 4 From the Report Name list, select Summary Report.

Step 5 Click View. Two tables are displayed: the AP Summary Report and the Fault Summary.

---

Note If the selected device has dual interfaces, two summary reports are displayed, one for each interface.

---

Table 5-14 AP Summary Report  

Column	Description
Name	The system name for the device.
As Of	The time the device's state last changed. For more information, see Time Display.
MAC Address	The device's MAC address.
IP Address	The device's IP address. Click to open up a browser window to the AP Summary Status.
Software Version	The version of software running on the device.
Number of Clients connected	The number of wireless clients connected to the device.
Number of Bridges Connected	The number of wireless bridges connected to the device.
Number of AP-Repeaters Connected	The number of AP repeaters connected to the device.
Model	Model number of the device.
SSID	The unique identifier the client device uses to associate with the access point.
Radio Cell Role	Indicates whether the device is used as a root or repeater.
Link to the Detailed Report	Click to see details. For more information, see Displaying a Detailed Report.
Link to the Association Report	Click to see associations. For more information, see Displaying a Current Client Association Report.
Link to the Access Point Web Page	Click to open up a browser window to the AP Summary Status.

For information on the Fault Summary, see Viewing Fault Details.

Step 6 To export the report, click Export. (See Exporting a Report.)

Step 7 To email the report, click Email Report. (See Emailing a Report.)

---

Displaying a Detailed Report

Procedure

---

Step 1 Select Reports > Current. The window refreshes with a device selector in the left pane.

Step 2 If you want to search for the device, use the dialog box in the left pane above the device selector:

a. From the list, select the method you want to use to search for the device: by name or by IP address.

b. Enter the IP address or name, or use an asterisk (*) as a wildcard to denote numbers and letters, then click Search. The requested device appears in the Search Results folder.

Step 3 From the device selector in the left pane, click to expand the folder and select the device for which you want a report. The right pane refreshes.

Step 4 From the Report Name list, select Detailed Report.

Step 5 Click View. In addition to the Detailed Report, the Fault Summary, and the EAP Authentication Report are also displayed.

---

Note If the selected device has dual interfaces, two summary reports are displayed, one for each interface.

---

Table 5-15 Detailed Report  

Column	Description
System Name	The system name for the device.
As Of	The time the device's state last changed. For more information, see Time Display.
MAC Address	The device's MAC address.
IP Address	The device's IP address. Click to open up a browser window to the AP Summary Status.
Software Version	The device's software version.
Number of Clients Connected	The number of wireless clients connected to the device.
Number of Bridges Connected	The number of bridges connected to the device.
Number of AP-Repeaters Connected	The number of AP repeaters connected to the device.
Model	The hardware model of the device.
SSID	The unique identifier the client device uses to associate with the access point.
Radio Cell Role	Indicates the role of the device.
Subnet Mask	The subnet mask.
Ensure Compatibility With 2Mbps Clients	Indicates whether it is compatible with 2Mbps clients.
Ensure Compatibility With non-Aironet 802.11	Indicates whether it is compatible with 802.11.
SNMP Trap Destination	The IP address or host name of the server running the SNMP Management software.
HTTP Port	The device's HTTP setting.
Hot StandBy	Indicates whether the hot standby unit is in monitoring mode. If true, the current unit is in monitoring mode.
Count of Access Point observed by this AP	Number of access points seen by the access points.
Current operating frequency channel	The radio channel being used.
Ethernet Port Status	The operational status of the Ethernet port.
Radio Port Status	The operational status of the radio port.
Transmit Power (mW)	The access point's transmission power setting in milliwatts.
Switch IP (to which this AP is attached)	The IP address of the switch to which this access point is attached.
Switch Name (to which this AP is attached)	The name of the switch to which this access point is attached.
Encryption type	Indicates that devices using WEP are allowed to communicate with the access point.
Length of WEP key 1 through 4 (in bits)	The WEP key length.
Authentication Type - Open System	Indicates whether any device, regardless of its WEP keys, can authenticate and attempt to associate.
Authentication Type - Shared Key	Indicates whether an access point sends a query to any device attempting to associate with the access point.
Link to the Access Point Web Page	Click to open up a browser window to the AP Summary Status.

•For Fault Summary information, see Viewing Fault Details.

•For EAP Authentication Report, see Displaying an EAP Authentication Report.

Step 6 To export the report, click Export. (See Exporting a Report.)

Step 7 To email the report, click Email Report. (See Emailing a Report.)

---

Displaying a Current Client Association Report

Procedure

---

Step 1 Select Reports > Current. The window refreshes with a device selector in the left pane.

Step 2 If you want to search for the device, use the dialog box in the left pane above the device selector:

a. From the list, select the method you want to use to search for the device: by name or by IP address.

b. Enter the IP address or name, or use an asterisk (*) as a wildcard to denote numbers and letters, then click Search. The requested device appears in the Search Results folder.

Step 3 From the device selector in the left pane, click to expand the folder and select the access point for which you want a report. The right pane refreshes.

Step 4 From the Report Name list, select Current Client Association Report.

Step 5 Click View. The group report is displayed with the following headings:

Table 5-16 Current Client Association Report  

Column	Description
Name	The name of the client associated with the access point.
IP Address	The IP address of the wireless client.
MAC Address	The wireless client's MAC address.
Device Type	The wireless client device type.
As Of	The time the device was last seen by the system. For more information, see Time Display.
State	The operational state of the device.