The NM-1FE2W, NM-2FE2W, NM-2W, NM-1FE1R2W, NM-1FE2W-V2 and NM-2FE2W-V2 WAN Interface Card carrier modules allow customers using Cisco 2600, 3600, 3700 and 3800 Series Routers to benefit from the increased performance and density capabilities delivered by this family of network modules. Features include auto-sensing 10/100 Mbps Fast Ethernet ports and TDM capabilities.
Figure 1. 10/100 LAN/WAN Combo Network Modules
INTRODUCTION
Table 1. Four different network modules are available to increase LAN/WAN densities for the Cisco 2600, 2691, 3600, 3700 and 3800 series of multi-service and Integrated Services routers.
Part Number
Description
NM-1FE2W/ and NM-1FE2W-V2
1-port 10/100 Ethernet 2 WAN Card Slot Network Module
NM-2FE2W and NM-2FE2W-V2
2-port 10/100 Ethernet 2 WAN Card Slot Network Module
NM-1FE1R2W
1-port 10/100 Ethernet 1 4/16 Token Ring 2 WAN Card Slot NM
NM-2W
2 WAN Card Slot Network Module (no LAN interface)
FEATURES
• Supported on Cisco 2600 (NM-2W only) 2691, 3600, 3700 and 3800 series Branch office routers
• Supports WICs and VWICs (see below for a complete list)
• Increase WIC density in Cisco 2600, 2691, 3700 and 3800 series
• Support for up to 8Mb throughput on a WIC interface
• 10/100 autosensing full/half duplex
• Full and half duplex Token Ring Support
• TDM enabled
The following WICs and VWICs are supported:
• WIC-1B-S/T
• WIC-1B-S/T-V3
• WIC-1B-U
• WIC-1B-V2
• WIC-1DSU-56K4
• WIC-1DSU-T1
• WIC-1DSU-T1-V2
• WIC-1T
• WIC-2T
• WIC-2A/S
• WIC-1AM
• WIC-2AM
• WIC-1ADSL
• WIC-1ADSL-V2
• WIC-1GSHDSL
• VWIC-1MFT-T1*
• VWIC-1MFT-E1*
• VWIC-1MFT-T1-DI*
• VWIC-1MFT-E1-DI*
• VWIC-2MFT-E1*
• VWIC-2MFT-T1*
• VWIC-2MFT-T1-DI*
• VWIC-2MFT-E1-DI*
• VWICs in data mode only
Table 2. The following table compares supported features and the major enhancements over the current legacy mixed media network modules.
Feature
NM-1E2W and NM-2E2W
NM-1FE2W, NM-2FE2W, NM-1FE1R2W
Max T1/E1 WIC Connections
2
4
VWIC Support
Limited
Full
WIC Support
Limited
Full
WIC Throughput
2Mb
8Mb
TDM Support
No
Yes
Ethernet Support
10Mb
10/100Mb
G.703 WIC Support**
No
Yes
Full Duplex Token Ring
No
Yes
** FCS 2HW/00
Table 3. Maximum number of network modules that are supported in the 2600, 2691, 3600, 3700 and 3800 families is shown below.
2600
2691
3620
3640
3660
3725/3825
3745/3845
NM-1FE2 AND NM-1FE2W-V2
N/A
1
2
4
6
2
4
NM-2FE2W AND NM-2FE2W-V2
N/A
1
2
4
6
2
4
NM-1FE1R2W
N/A
1
2
4
6
2
4
NM-2W
1
1
1
3
6
2
4
ORDERABILITY, AVAILABILITY, COMPATIBILITY, MINIMUM SOFTWARE, AND MEMORY REQUIREMENTS
Table 4. The 10/100 LAN/WAN combo Network Modules product numbers and description are listed below.
Product Number
Description
NM-1FE2W/NM-1FE2W-V2
1-port 10/100 Ethernet with 2 WAN Card Slot Network Module
NM-2FE2W/NM-2FE2W-V2
2-port 10/100 Ethernet with 2 WAN Card Slot Network Module
NM-1FE1R2W
1-port 10/100 Ethernet 1 4/16 Token Ring 2 WAN Card Slot NM
For the NM-1FE2W, NM-2FE2W, NM-1FE1R2W, and NM-2W the minimum level of IOS is 12.0(7)XK or 12.1(1)T.
For the NM-1FE2W-V2 and NM-2FE2W-V2 the minimum level IOS is 12.2(12)M and 12.2(13)T.
Table 5. 10/100 LAN/WAN combo Network Modules (NM-1FE2W, NM-2FE2W, NM-1FE1R2W, and NM-2W) platforms supported, minimum Cisco IOS® Release, minimum Memory and Maximum Number Supported.
Product
Minimum Cisco IOS Software Required
IOS Feature Set
Minimum DRAM Memory*
Maximum Supported
Cisco 2600 Series
12.0(7)XK
All Cisco IOS Feature Sets
32 MB
1
Cisco 2600XM Series
12.2(8)T
All Cisco IOS Feature Sets
32 MB
1
Cisco 2691
12.2(8)T
All Cisco IOS Feature Sets
64 MB
1
Cisco 2811, 2821, 2851
N/A
N/A
N/A
Not supported
Cisco 3620
12.0(7)XK
Any Cisco IOS Feature Set
32 MB
2**
Cisco 3640
12.0(7)XK
All Cisco IOS Feature Sets
32 MB
4**
Cisco 3660
12.0(7)XK
All Cisco IOS Feature Sets
32 MB
6
Cisco 3725
12.2(8)T
All Cisco IOS Feature Sets
N/A
2
Cisco 3825
12.3(11)T
All Cisco IOS feature sets
N/A
2
Cisco 3745
12.2(8)T
All Cisco IOS Feature Sets
N/A
4
Cisco 3845
12.3(11)T
All Cisco IOS Feature sets
N/A
4
* The NM-1FE2W-V2 and NM-2FE2W-V2 have the same memory requirements as the non-V2 network modules.
** Only 1 of the NM-2W is supported in the 3620, and only 3 NM-2W are supported in the 3640.
PHYSICAL SPECIFICATIONS
Table 6. Standards and Compliance Support
Product Feature
Product Specifications
Dimensions
1.55 x 7.10 x 7.2 in (H x W x D)
Weight
2.5 lbs. Maximum
Environmental Conditions
• Operating temp. 32°-104° F (0° -40° C)
• Nonoperating temp. -13° to -158° F (-25 to 70° C)
Power Requirements
15 watts Maximum
Relative Humidity
5 to 95%
MTBF
• NM-2W-1,720,096 hours
• NM-1FE2W and NM-1FE2W-V2-846,192 hours
• NM-2FE2W and NM-2FE2W-V2-569,302 hours
• NM-1FE1R2W-507,634 hours
Protocols Supported
Full Cisco IOS Software as of 12.0(7)XK
WIC Performance
Up to 8Mb/s per network module
EMI
FCC Part 15 Class B-CISPR 22 Class B
Cabling
WAN cables dependant on WICs. LAN interfaces have 10/100BaseT cables for Ethernet and STP/UTP cables for Token Ring
LEDs
Token ring 4/16 speed indication. Ethernet 10/100 Speed Indication. Link and full Duplex LEDS
Network Interfaces
Compatible with all existing network modules and WICS supported by Cisco 2600/2691/3600/3700/3800 routers
SUPPORTED MANAGEMENT INFORMATION BASE (MLBS)
The 10/100 LAN/WAN network modules support the standard Management Information Base (MIBs).
For descriptions of supported MIBs and how to use MIBs, see the Cisco MIB web site at:
