Document ID: 12313
Contents
Introduction
Prerequisites
Requirements
Components Used
Conventions
Configure
Network Diagram
Configurations
Verify
Troubleshoot
Related Information
Introduction
This document provides information on running TCP/IP datagram, TCP/IP offload, Cisco Systems Network Architecture (SNA), and Cisco TN3270 Server concurrently on the same Channel Interface Processor (CIP).
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
This document is not restricted to specific software and hardware versions.
Conventions
For more information on document conventions, refer to Cisco Technical Tips Conventions.
Configure
In this section, you are presented with the information to configure the features described in this document.
Note: To find additional information on the commands used in this document, use the Command Lookup Tool (registered customers only) .
Network Diagram
This document uses the network setup shown in the diagram below.
Configurations
This document uses the configurations shown below.
|
IOCP |
|---|
RESOURCE PARTITION=((HOST10,1),(HOST11,2),(HOST20,3)) CHPID PATH=((0A)),TYPE=CNC,SHARED,PARTITION=((HOST10,HOST11,HOST20)) CNTLUNIT CUNUMBR=0581,PATH=(0A),UNITADD=((10,32)),UNIT=SCTC,CUADD=1 CNTLUNIT CUNUMBR=0582,PATH=(0A),UNITADD=((10,32)),UNIT=SCTC,CUADD=2 CNTLUNIT CUNUMBR=0583,PATH=(0A),UNITADD=((10,32)),UNIT=SCTC,CUADD=3 IODEVICE ADDRESS=(100,32),CUNUMBR=(0581),UNIT=SCTC,PARTITION=HOST10 IODEVICE ADDRESS=(200,32),CUNUMBR=(0582),UNIT=SCTC,PARTITION=HOST11 IODEVICE ADDRESS=(300,32),CUNUMBR=(0583),UNIT=SCTC,PARTITION=HOST20 |
|
MVS and VTAM XCA Major Node |
|---|
TSTP5BE VBUILD TYPE=XCA
PRTP5BE PORT ADAPNO=1,CUADDR=206,SAPADDR=04,MEDIUM=RING,TIMER=60
*
* DIAL=YES on GROUP macro defines PU2.0/PU2.1 devices
*
GRPP5BE GROUP ANSWER=ON, X
AUTOGEN=(100,L,P), X
CALL=INOUT, X
DIAL=YES, X
ISTATUS=ACTIVE
|
|
MVS and VTAM LUGROUP Major Node |
|---|
VBUILD TYPE=LUGROUP
DDDLUGMP LUGROUP
327905E LU DLOGMOD=SNX32705,LOGAPPL=VTPPROD, X
MODETAB=ISTINCLM,USSTAB=ISTINCDT, X
SSCPFM=USS3270
327904E LU DLOGMOD=SNX32704,LOGAPPL=VTPPROD, X
MODETAB=ISTINCLM,USSTAB=ISTINCDT, X
SSCPFM=USS3270
327903E LU DLOGMOD=SNX32703,LOGAPPL=VTPPROD, X
MODETAB=ISTINCLM,USSTAB=ISTINCDT, X
SSCPFM=USS3270
327902E LU DLOGMOD=SNX32702,LOGAPPL=VTPPROD, X
MODETAB=ISTINCLM,USSTAB=ISTINCDT, X
SSCPFM=USS3270
327805E LU DLOGMOD=SNX32705,LOGAPPL=VTPPROD, X
MODETAB=ISTINCLM,USSTAB=ISTINCDT, X
SSCPFM=USS3270
327804E LU DLOGMOD=SNX32704,LOGAPPL=VTPPROD, X
MODETAB=ISTINCLM,USSTAB=ISTINCDT, X
SSCPFM=USS3270
327803E LU DLOGMOD=SNX32703,LOGAPPL=VTPPROD, X
MODETAB=ISTINCLM,USSTAB=ISTINCDT, X
SSCPFM=USS3270
327802E LU DLOGMOD=SNX32702,LOGAPPL=VTPPROD, X
MODETAB=ISTINCLM,USSTAB=ISTINCDT, X
SSCPFM=USS3270
327802 LU DLOGMOD=D4C32782,LOGAPPL=VTPPROD, X
MODETAB=ISTINCLM,USSTAB=ISTINCDT, X
SSCPFM=USS3270
327803 LU DLOGMOD=D4C32783,LOGAPPL=VTPPROD, X
MODETAB=ISTINCLM,USSTAB=ISTINCDT, X
SSCPFM=USS3270
327804 LU DLOGMOD=D4C32784,LOGAPPL=VTPPROD, X
MODETAB=ISTINCLM,USSTAB=ISTINCDT, X
SSCPFM=USS3270
327805 LU DLOGMOD=D4C32785,LOGAPPL=VTPPROD, X
MODETAB=ISTINCLM,USSTAB=ISTINCDT, X
SSCPFM=USS3270
327806 LU DLOGMOD=D4C32782,LOGAPPL=VTPPROD, X
MODETAB=ISTINCLM,USSTAB=ISTINCDT, X
SSCPFM=USS3270
|
|
MVS and VTAM Switched Major Node |
|---|
VBUILD TYPE=SWNET,MAXNO=15,MAXGRP=5
* STATOPT='TOKEN RING PUS'
E194TRV0 PU IDBLK=05D, X
IDNUM=49974, X
DISCNT=NO, X
DLOGMOD=A3278M2, X
MAXOUT=7, X
ADDR=01, X
MAXPATH=2, X
MAXDATA=521, X
LUGROUP=DDDLUGMP, X
LUSEED=T10V0###, X
PACING=2, X
PUTYPE=2, X
VPACING=0, X
SSCPFM=USS3270, X
ISTATUS=ACTIVE, X
MODETAB=ISTINCLM, X
LOGAPPL=VTPPROD, X
USSTAB=ISTINCDT
* STATOPT='CISCO CIP 194'
*
E194TRV1 PU IDBLK=05D, X
IDNUM=49975, X
DISCNT=NO, X
DLOGMOD=A3278M2, X
MAXOUT=7, X
ADDR=01, X
MAXPATH=2, X
MAXDATA=521, X
LUGROUP=DDDLUGMP, X
LUSEED=T10V1###, X
PACING=2, X
PUTYPE=2, X
VPACING=0, X
SSCPFM=USS3270, X
ISTATUS=ACTIVE, X
MODETAB=ISTINCLM, X
LOGAPPL=VTPPROD, X
USSTAB=ISTINCDT
* STATOPT='CISCO CIP 194'
*
*
E194TRV2 PU IDBLK=05D, X
IDNUM=49976, X
DISCNT=NO, X
DLOGMOD=A3278M2, X
MAXOUT=7, X
ADDR=01, X
MAXPATH=2, X
MAXDATA=521, X
LUGROUP=DDDLUGMP, X
LUSEED=T10V2###, X
PACING=2, X
PUTYPE=2, X
VPACING=0, X
SSCPFM=USS3270, X
ISTATUS=ACTIVE, X
MODETAB=ISTINCLM, X
LOGAPPL=VTPPROD, X
USSTAB=ISTINCDT
* STATOPT='CISCO CIP 194'
*
E194TRV3 PU IDBLK=05D, X
IDNUM=49977, X
DISCNT=NO, X
DLOGMOD=A3278M2, X
MAXOUT=7, X
ADDR=01, X
MAXPATH=2, X
MAXDATA=521, X
LUGROUP=DDDLUGMP, X
LUSEED=T10V3###, X
PACING=2, X
PUTYPE=2, X
VPACING=0, X
SSCPFM=USS3270, X
ISTATUS=ACTIVE, X
MODETAB=ISTINCLM, X
LOGAPPL=VTPPROD, X
USSTAB=ISTINCDT
* STATOPT='CISCO CIP 194'
*
E194TRV4 PU IDBLK=05D, X
IDNUM=49978, X
DISCNT=NO, X
DLOGMOD=A3278M2, X
MAXOUT=7, X
ADDR=01, X
MAXPATH=2, X
MAXDATA=521, X
LUGROUP=DDDLUGMP, X
LUSEED=T10V4###, X
PACING=2, X
PUTYPE=2, X
VPACING=0, X
SSCPFM=USS3270, X
ISTATUS=ACTIVE, X
MODETAB=ISTINCLM, X
LOGAPPL=VTPPROD, X
USSTAB=ISTINCDT
* STATOPT='CISCO CIP 194'
|
|
Router Configuration for MVS and VTAM |
|---|
Router#wr t Building configuration... .. .. interface Channel3/0 description CISCO Channel Interface Processor ip address 163.241.167.6 255.255.255.248 no ip redirects ip route-cache same-interface ip route-cache cbus no keepalive offload 0133 10 163.241.167.3 Host20 C7000 TCPIP TCPIP TCPIP API broadcast claw 0111 10 163.241.167.1 Host10 C7000 TCPIP TCPIP broadcast claw 0122 10 163.241.167.2 Host11 C7000 TCPIP TCPIP broadcast csna 0133 16 maxpiu 8192 !--- The above is used for a regular Cisco SNA session. csna 0122 16 maxpiu 8192 !--- The above is used for a TN3270 session in this example. ! interface Channel3/2 description TN3270 Server ip address 163.241.167.17 255.255.255.248 no keepalive max-llc2-sessions 4000 lan TokenRing 1 adapter 0 4000.6195.9980 adapter 1 4000.6194.9981 tn3270-server maximum-lus 1000 pu E194TRV0 05D49974 163.241.167.18 token-adap 1 70 rmac 4000.6195.9981 rsap 04 lu-seed T10V0### pu E194TRV1 05D49975 163.241.167.18 token-adap 1 74 rmac 4000.6195.9981 rsap 04 lu-seed T10V1### pu E194TRV2 05D49976 163.241.167.18 token-adap 1 78 rmac 4000.6195.9981 rsap 04 lu-seed T10V2### pu E194TRV3 05D49977 163.241.167.18 token-adap 1 82 rmac 4000.6195.9981 rsap 04 lu-seed T10V3### pu E194TRV4 05D49978 163.241.167.18 token-adap 1 86 rmac 4000.6195.9981 rsap 04 lu-seed T10V4### logging buffered 50000 |
In issuing the maximum-lus 1000 command in the Router Configuration for MVS and VTAM above, the maximum number of TN3270 sessions that are supported on this adapter is limited. Each Physical Unit (PU) supports 255 Logical Units (LUs). In defining 5 PUs, 1275 LUs remain available. However, because of the maximum-lus 1000 command, no more than 1000 LUs may be used.
Verify
There is currently no verification procedure available for this configuration.
Troubleshoot
There is currently no specific troubleshooting information available for this configuration.
Related Information
| Updated: Sep 09, 2005 | Document ID: 12313 |